| Message ID | 1598651234-29826-1-git-send-email-stefan.wahren@i2se.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | mmc: sdhci-iproc: Enable eMMC DDR 3.3V support for bcm2711 | expand |
On Fri, 28 Aug 2020 at 23:48, Stefan Wahren <stefan.wahren@i2se.com> wrote: > > The emmc2 interface on the bcm2711 supports DDR modes for eMMC devices > running at 3.3V. This allows to run eMMC module with 3.3V signaling voltage > at DDR52 mode on the Raspberry Pi 4 using a SD adapter: > > clock: 52000000 Hz > actual clock: 50000000 Hz > vdd: 21 (3.3 ~ 3.4 V) > bus mode: 2 (push-pull) > chip select: 0 (don't care) > power mode: 2 (on) > bus width: 2 (4 bits) > timing spec: 8 (mmc DDR52) > signal voltage: 0 (3.30 V) > driver type: 0 (driver type B) > > Link: https://github.com/raspberrypi/linux/issues/3802 > Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Applied for next, thanks! Kind regards Uffe > --- > drivers/mmc/host/sdhci-iproc.c | 1 + > 1 file changed, 1 insertion(+) > > diff --git a/drivers/mmc/host/sdhci-iproc.c b/drivers/mmc/host/sdhci-iproc.c > index e2d8dfe..b540aa6 100644 > --- a/drivers/mmc/host/sdhci-iproc.c > +++ b/drivers/mmc/host/sdhci-iproc.c > @@ -283,6 +283,7 @@ static const struct sdhci_pltfm_data sdhci_bcm2711_pltfm_data = { > > static const struct sdhci_iproc_data bcm2711_data = { > .pdata = &sdhci_bcm2711_pltfm_data, > + .mmc_caps = MMC_CAP_3_3V_DDR, > }; > > static const struct of_device_id sdhci_iproc_of_match[] = { > -- > 2.7.4 >
diff --git a/drivers/mmc/host/sdhci-iproc.c b/drivers/mmc/host/sdhci-iproc.c index e2d8dfe..b540aa6 100644 --- a/drivers/mmc/host/sdhci-iproc.c +++ b/drivers/mmc/host/sdhci-iproc.c @@ -283,6 +283,7 @@ static const struct sdhci_pltfm_data sdhci_bcm2711_pltfm_data = { static const struct sdhci_iproc_data bcm2711_data = { .pdata = &sdhci_bcm2711_pltfm_data, + .mmc_caps = MMC_CAP_3_3V_DDR, }; static const struct of_device_id sdhci_iproc_of_match[] = {
The emmc2 interface on the bcm2711 supports DDR modes for eMMC devices running at 3.3V. This allows to run eMMC module with 3.3V signaling voltage at DDR52 mode on the Raspberry Pi 4 using a SD adapter: clock: 52000000 Hz actual clock: 50000000 Hz vdd: 21 (3.3 ~ 3.4 V) bus mode: 2 (push-pull) chip select: 0 (don't care) power mode: 2 (on) bus width: 2 (4 bits) timing spec: 8 (mmc DDR52) signal voltage: 0 (3.30 V) driver type: 0 (driver type B) Link: https://github.com/raspberrypi/linux/issues/3802 Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> --- drivers/mmc/host/sdhci-iproc.c | 1 + 1 file changed, 1 insertion(+)