| Message ID | 1602087290-18020-1-git-send-email-hugues.fruchet@st.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | media: stm32-dcmi: add support of BT656 bus | expand |
Hi Hugues, On Wed, Oct 07, 2020 at 06:14:50PM +0200, Hugues Fruchet wrote: > Add support of BT656 embedded synchronization bus. > This mode allows to save hardware synchro lines hsync & vsync > by replacing them with synchro codes embedded in data stream. > This bus type is only compatible with 8 bits width data bus. > Due to reserved values 0x00 & 0xff used for synchro codes, > valid data only vary from 0x1 to 0xfe, this is up to sensor > to clip accordingly pixel data. As a consequence of this > clipping, JPEG is not supported when using this bus type. > DCMI crop feature is also not available with this bus type. You can have more than 62 characters per line. In fact, 75 is the recommended maximum. You should also amend the bindings to cover BT.656 mode. Also bus-type should probably be made mandatory, too. > > Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> > --- > drivers/media/platform/stm32/stm32-dcmi.c | 37 +++++++++++++++++++++++++++++-- > 1 file changed, 35 insertions(+), 2 deletions(-) > > diff --git a/drivers/media/platform/stm32/stm32-dcmi.c b/drivers/media/platform/stm32/stm32-dcmi.c > index fd1c41c..d7d7cdb 100644 > --- a/drivers/media/platform/stm32/stm32-dcmi.c > +++ b/drivers/media/platform/stm32/stm32-dcmi.c > @@ -157,6 +157,7 @@ struct stm32_dcmi { > struct vb2_queue queue; > > struct v4l2_fwnode_bus_parallel bus; > + enum v4l2_mbus_type bus_type; > struct completion complete; > struct clk *mclk; > enum state state; > @@ -777,6 +778,23 @@ static int dcmi_start_streaming(struct vb2_queue *vq, unsigned int count) > if (dcmi->bus.flags & V4L2_MBUS_PCLK_SAMPLE_RISING) > val |= CR_PCKPOL; > > + /* > + * BT656 embedded synchronisation bus mode. > + * > + * Default SAV/EAV mode is supported here with default codes > + * SAV=0xff000080 & EAV=0xff00009d. > + * With DCMI this means LSC=SAV=0x80 & LEC=EAV=0x9d. > + */ > + if (dcmi->bus_type == V4L2_MBUS_BT656) { > + val |= CR_ESS; > + > + /* Unmask all codes */ > + reg_write(dcmi->regs, DCMI_ESUR, 0xffffffff);/* FEC:LEC:LSC:FSC */ > + > + /* Trig on LSC=0x80 & LEC=0x9d codes, ignore FSC and FEC */ > + reg_write(dcmi->regs, DCMI_ESCR, 0xff9d80ff);/* FEC:LEC:LSC:FSC */ > + } > + > reg_write(dcmi->regs, DCMI_CR, val); > > /* Set crop */ > @@ -1067,8 +1085,9 @@ static int dcmi_set_fmt(struct stm32_dcmi *dcmi, struct v4l2_format *f) > if (ret) > return ret; > > - /* Disable crop if JPEG is requested */ > - if (pix->pixelformat == V4L2_PIX_FMT_JPEG) > + /* Disable crop if JPEG is requested or BT656 bus is selected */ > + if (pix->pixelformat == V4L2_PIX_FMT_JPEG && > + dcmi->bus_type != V4L2_MBUS_BT656) > dcmi->do_crop = false; > > /* pix to mbus format */ > @@ -1592,6 +1611,11 @@ static int dcmi_formats_init(struct stm32_dcmi *dcmi) > if (dcmi_formats[i].mbus_code != mbus_code.code) > continue; > > + /* Exclude JPEG if BT656 bus is selected */ > + if (dcmi_formats[i].fourcc == V4L2_PIX_FMT_JPEG && > + dcmi->bus_type == V4L2_MBUS_BT656) > + continue; > + > /* Code supported, have we got this fourcc yet? */ > for (j = 0; j < num_fmts; j++) > if (sd_fmts[j]->fourcc == > @@ -1873,9 +1897,18 @@ static int dcmi_probe(struct platform_device *pdev) > dev_err(&pdev->dev, "CSI bus not supported\n"); > return -ENODEV; > } > + > + if (ep.bus_type == V4L2_MBUS_BT656 && > + ep.bus.parallel.bus_width != 8) { > + dev_err(&pdev->dev, "BT656 bus conflicts with %d bits bus width (8 bits required)\n", > + ep.bus.parallel.bus_width); bus_width is unsigned here. > + return -ENODEV; > + } > + > dcmi->bus.flags = ep.bus.parallel.flags; > dcmi->bus.bus_width = ep.bus.parallel.bus_width; > dcmi->bus.data_shift = ep.bus.parallel.data_shift; > + dcmi->bus_type = ep.bus_type; > > irq = platform_get_irq(pdev, 0); > if (irq <= 0)
Hi Sakari, Thanks for reviewing, On 10/13/20 11:07 AM, Sakari Ailus wrote: > Hi Hugues, > > On Wed, Oct 07, 2020 at 06:14:50PM +0200, Hugues Fruchet wrote: >> Add support of BT656 embedded synchronization bus. >> This mode allows to save hardware synchro lines hsync & vsync >> by replacing them with synchro codes embedded in data stream. >> This bus type is only compatible with 8 bits width data bus. >> Due to reserved values 0x00 & 0xff used for synchro codes, >> valid data only vary from 0x1 to 0xfe, this is up to sensor >> to clip accordingly pixel data. As a consequence of this >> clipping, JPEG is not supported when using this bus type. >> DCMI crop feature is also not available with this bus type. > > You can have more than 62 characters per line. In fact, 75 is the > recommended maximum. > > You should also amend the bindings to cover BT.656 mode. Also bus-type > should probably be made mandatory, too. Will do both. > >> >> Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> >> --- >> drivers/media/platform/stm32/stm32-dcmi.c | 37 +++++++++++++++++++++++++++++-- >> 1 file changed, 35 insertions(+), 2 deletions(-) >> >> diff --git a/drivers/media/platform/stm32/stm32-dcmi.c b/drivers/media/platform/stm32/stm32-dcmi.c >> index fd1c41c..d7d7cdb 100644 >> --- a/drivers/media/platform/stm32/stm32-dcmi.c >> +++ b/drivers/media/platform/stm32/stm32-dcmi.c >> @@ -157,6 +157,7 @@ struct stm32_dcmi { >> struct vb2_queue queue; >> >> struct v4l2_fwnode_bus_parallel bus; >> + enum v4l2_mbus_type bus_type; >> struct completion complete; >> struct clk *mclk; >> enum state state; >> @@ -777,6 +778,23 @@ static int dcmi_start_streaming(struct vb2_queue *vq, unsigned int count) >> if (dcmi->bus.flags & V4L2_MBUS_PCLK_SAMPLE_RISING) >> val |= CR_PCKPOL; >> >> + /* >> + * BT656 embedded synchronisation bus mode. >> + * >> + * Default SAV/EAV mode is supported here with default codes >> + * SAV=0xff000080 & EAV=0xff00009d. >> + * With DCMI this means LSC=SAV=0x80 & LEC=EAV=0x9d. >> + */ >> + if (dcmi->bus_type == V4L2_MBUS_BT656) { >> + val |= CR_ESS; >> + >> + /* Unmask all codes */ >> + reg_write(dcmi->regs, DCMI_ESUR, 0xffffffff);/* FEC:LEC:LSC:FSC */ >> + >> + /* Trig on LSC=0x80 & LEC=0x9d codes, ignore FSC and FEC */ >> + reg_write(dcmi->regs, DCMI_ESCR, 0xff9d80ff);/* FEC:LEC:LSC:FSC */ >> + } >> + >> reg_write(dcmi->regs, DCMI_CR, val); >> >> /* Set crop */ >> @@ -1067,8 +1085,9 @@ static int dcmi_set_fmt(struct stm32_dcmi *dcmi, struct v4l2_format *f) >> if (ret) >> return ret; >> >> - /* Disable crop if JPEG is requested */ >> - if (pix->pixelformat == V4L2_PIX_FMT_JPEG) >> + /* Disable crop if JPEG is requested or BT656 bus is selected */ >> + if (pix->pixelformat == V4L2_PIX_FMT_JPEG && >> + dcmi->bus_type != V4L2_MBUS_BT656) >> dcmi->do_crop = false; >> >> /* pix to mbus format */ >> @@ -1592,6 +1611,11 @@ static int dcmi_formats_init(struct stm32_dcmi *dcmi) >> if (dcmi_formats[i].mbus_code != mbus_code.code) >> continue; >> >> + /* Exclude JPEG if BT656 bus is selected */ >> + if (dcmi_formats[i].fourcc == V4L2_PIX_FMT_JPEG && >> + dcmi->bus_type == V4L2_MBUS_BT656) >> + continue; >> + >> /* Code supported, have we got this fourcc yet? */ >> for (j = 0; j < num_fmts; j++) >> if (sd_fmts[j]->fourcc == >> @@ -1873,9 +1897,18 @@ static int dcmi_probe(struct platform_device *pdev) >> dev_err(&pdev->dev, "CSI bus not supported\n"); >> return -ENODEV; >> } >> + >> + if (ep.bus_type == V4L2_MBUS_BT656 && >> + ep.bus.parallel.bus_width != 8) { >> + dev_err(&pdev->dev, "BT656 bus conflicts with %d bits bus width (8 bits required)\n", >> + ep.bus.parallel.bus_width); > > bus_width is unsigned here. I will fix it. > >> + return -ENODEV; >> + } >> + >> dcmi->bus.flags = ep.bus.parallel.flags; >> dcmi->bus.bus_width = ep.bus.parallel.bus_width; >> dcmi->bus.data_shift = ep.bus.parallel.data_shift; >> + dcmi->bus_type = ep.bus_type; >> >> irq = platform_get_irq(pdev, 0); >> if (irq <= 0) > BR, Hugues.
Hi Sakari, I have questions about "bus-type" handling below. On 10/15/20 5:41 PM, Hugues FRUCHET wrote: > Hi Sakari, > > Thanks for reviewing, > > On 10/13/20 11:07 AM, Sakari Ailus wrote: >> Hi Hugues, >> >> On Wed, Oct 07, 2020 at 06:14:50PM +0200, Hugues Fruchet wrote: >>> Add support of BT656 embedded synchronization bus. >>> This mode allows to save hardware synchro lines hsync & vsync >>> by replacing them with synchro codes embedded in data stream. >>> This bus type is only compatible with 8 bits width data bus. >>> Due to reserved values 0x00 & 0xff used for synchro codes, >>> valid data only vary from 0x1 to 0xfe, this is up to sensor >>> to clip accordingly pixel data. As a consequence of this >>> clipping, JPEG is not supported when using this bus type. >>> DCMI crop feature is also not available with this bus type. >> >> You can have more than 62 characters per line. In fact, 75 is the >> recommended maximum. >> >> You should also amend the bindings to cover BT.656 mode. Also bus-type >> should probably be made mandatory, too. > Will do both. > My understanding was that parallel BT656 bus is handled by the absence of hsync/vsync-active, as stated in Documentation/devicetree/bindings/media/video-interfaces.txt: " Note, that if HSYNC and VSYNC polarities are not specified, embedded synchronization may be required, where supported. " Do you want to enforce usage of "bus-type" now in order to be more explicit on parallel or bt656 ? If I change binding to make "bus-type" required, I have to change the current board devicetree files to add support of it, and I would prefer to not do that. Is there a way to put "bus-type" as not mandatory and rely on absence of hsync/vysnc to trig BT656 ? I will nevertheless amend bindings in order to document that. What do you suggest ? >> >>> >>> Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> >>> --- >>> drivers/media/platform/stm32/stm32-dcmi.c | 37 >>> +++++++++++++++++++++++++++++-- >>> 1 file changed, 35 insertions(+), 2 deletions(-) >>> >>> diff --git a/drivers/media/platform/stm32/stm32-dcmi.c >>> b/drivers/media/platform/stm32/stm32-dcmi.c >>> index fd1c41c..d7d7cdb 100644 >>> --- a/drivers/media/platform/stm32/stm32-dcmi.c >>> +++ b/drivers/media/platform/stm32/stm32-dcmi.c >>> @@ -157,6 +157,7 @@ struct stm32_dcmi { >>> struct vb2_queue queue; >>> struct v4l2_fwnode_bus_parallel bus; >>> + enum v4l2_mbus_type bus_type; >>> struct completion complete; >>> struct clk *mclk; >>> enum state state; >>> @@ -777,6 +778,23 @@ static int dcmi_start_streaming(struct vb2_queue >>> *vq, unsigned int count) >>> if (dcmi->bus.flags & V4L2_MBUS_PCLK_SAMPLE_RISING) >>> val |= CR_PCKPOL; >>> + /* >>> + * BT656 embedded synchronisation bus mode. >>> + * >>> + * Default SAV/EAV mode is supported here with default codes >>> + * SAV=0xff000080 & EAV=0xff00009d. >>> + * With DCMI this means LSC=SAV=0x80 & LEC=EAV=0x9d. >>> + */ >>> + if (dcmi->bus_type == V4L2_MBUS_BT656) { >>> + val |= CR_ESS; >>> + >>> + /* Unmask all codes */ >>> + reg_write(dcmi->regs, DCMI_ESUR, 0xffffffff);/* >>> FEC:LEC:LSC:FSC */ >>> + >>> + /* Trig on LSC=0x80 & LEC=0x9d codes, ignore FSC and FEC */ >>> + reg_write(dcmi->regs, DCMI_ESCR, 0xff9d80ff);/* >>> FEC:LEC:LSC:FSC */ >>> + } >>> + >>> reg_write(dcmi->regs, DCMI_CR, val); >>> /* Set crop */ >>> @@ -1067,8 +1085,9 @@ static int dcmi_set_fmt(struct stm32_dcmi >>> *dcmi, struct v4l2_format *f) >>> if (ret) >>> return ret; >>> - /* Disable crop if JPEG is requested */ >>> - if (pix->pixelformat == V4L2_PIX_FMT_JPEG) >>> + /* Disable crop if JPEG is requested or BT656 bus is selected */ >>> + if (pix->pixelformat == V4L2_PIX_FMT_JPEG && >>> + dcmi->bus_type != V4L2_MBUS_BT656) >>> dcmi->do_crop = false; >>> /* pix to mbus format */ >>> @@ -1592,6 +1611,11 @@ static int dcmi_formats_init(struct stm32_dcmi >>> *dcmi) >>> if (dcmi_formats[i].mbus_code != mbus_code.code) >>> continue; >>> + /* Exclude JPEG if BT656 bus is selected */ >>> + if (dcmi_formats[i].fourcc == V4L2_PIX_FMT_JPEG && >>> + dcmi->bus_type == V4L2_MBUS_BT656) >>> + continue; >>> + >>> /* Code supported, have we got this fourcc yet? */ >>> for (j = 0; j < num_fmts; j++) >>> if (sd_fmts[j]->fourcc == >>> @@ -1873,9 +1897,18 @@ static int dcmi_probe(struct platform_device >>> *pdev) >>> dev_err(&pdev->dev, "CSI bus not supported\n"); >>> return -ENODEV; >>> } >>> + >>> + if (ep.bus_type == V4L2_MBUS_BT656 && >>> + ep.bus.parallel.bus_width != 8) { >>> + dev_err(&pdev->dev, "BT656 bus conflicts with %d bits bus >>> width (8 bits required)\n", >>> + ep.bus.parallel.bus_width); >> >> bus_width is unsigned here. > I will fix it. > >> >>> + return -ENODEV; >>> + } >>> + >>> dcmi->bus.flags = ep.bus.parallel.flags; >>> dcmi->bus.bus_width = ep.bus.parallel.bus_width; >>> dcmi->bus.data_shift = ep.bus.parallel.data_shift; >>> + dcmi->bus_type = ep.bus_type; >>> irq = platform_get_irq(pdev, 0); >>> if (irq <= 0) >> > > BR, > Hugues. BR, Hugues.
diff --git a/drivers/media/platform/stm32/stm32-dcmi.c b/drivers/media/platform/stm32/stm32-dcmi.c index fd1c41c..d7d7cdb 100644 --- a/drivers/media/platform/stm32/stm32-dcmi.c +++ b/drivers/media/platform/stm32/stm32-dcmi.c @@ -157,6 +157,7 @@ struct stm32_dcmi { struct vb2_queue queue; struct v4l2_fwnode_bus_parallel bus; + enum v4l2_mbus_type bus_type; struct completion complete; struct clk *mclk; enum state state; @@ -777,6 +778,23 @@ static int dcmi_start_streaming(struct vb2_queue *vq, unsigned int count) if (dcmi->bus.flags & V4L2_MBUS_PCLK_SAMPLE_RISING) val |= CR_PCKPOL; + /* + * BT656 embedded synchronisation bus mode. + * + * Default SAV/EAV mode is supported here with default codes + * SAV=0xff000080 & EAV=0xff00009d. + * With DCMI this means LSC=SAV=0x80 & LEC=EAV=0x9d. + */ + if (dcmi->bus_type == V4L2_MBUS_BT656) { + val |= CR_ESS; + + /* Unmask all codes */ + reg_write(dcmi->regs, DCMI_ESUR, 0xffffffff);/* FEC:LEC:LSC:FSC */ + + /* Trig on LSC=0x80 & LEC=0x9d codes, ignore FSC and FEC */ + reg_write(dcmi->regs, DCMI_ESCR, 0xff9d80ff);/* FEC:LEC:LSC:FSC */ + } + reg_write(dcmi->regs, DCMI_CR, val); /* Set crop */ @@ -1067,8 +1085,9 @@ static int dcmi_set_fmt(struct stm32_dcmi *dcmi, struct v4l2_format *f) if (ret) return ret; - /* Disable crop if JPEG is requested */ - if (pix->pixelformat == V4L2_PIX_FMT_JPEG) + /* Disable crop if JPEG is requested or BT656 bus is selected */ + if (pix->pixelformat == V4L2_PIX_FMT_JPEG && + dcmi->bus_type != V4L2_MBUS_BT656) dcmi->do_crop = false; /* pix to mbus format */ @@ -1592,6 +1611,11 @@ static int dcmi_formats_init(struct stm32_dcmi *dcmi) if (dcmi_formats[i].mbus_code != mbus_code.code) continue; + /* Exclude JPEG if BT656 bus is selected */ + if (dcmi_formats[i].fourcc == V4L2_PIX_FMT_JPEG && + dcmi->bus_type == V4L2_MBUS_BT656) + continue; + /* Code supported, have we got this fourcc yet? */ for (j = 0; j < num_fmts; j++) if (sd_fmts[j]->fourcc == @@ -1873,9 +1897,18 @@ static int dcmi_probe(struct platform_device *pdev) dev_err(&pdev->dev, "CSI bus not supported\n"); return -ENODEV; } + + if (ep.bus_type == V4L2_MBUS_BT656 && + ep.bus.parallel.bus_width != 8) { + dev_err(&pdev->dev, "BT656 bus conflicts with %d bits bus width (8 bits required)\n", + ep.bus.parallel.bus_width); + return -ENODEV; + } + dcmi->bus.flags = ep.bus.parallel.flags; dcmi->bus.bus_width = ep.bus.parallel.bus_width; dcmi->bus.data_shift = ep.bus.parallel.data_shift; + dcmi->bus_type = ep.bus_type; irq = platform_get_irq(pdev, 0); if (irq <= 0)
Add support of BT656 embedded synchronization bus. This mode allows to save hardware synchro lines hsync & vsync by replacing them with synchro codes embedded in data stream. This bus type is only compatible with 8 bits width data bus. Due to reserved values 0x00 & 0xff used for synchro codes, valid data only vary from 0x1 to 0xfe, this is up to sensor to clip accordingly pixel data. As a consequence of this clipping, JPEG is not supported when using this bus type. DCMI crop feature is also not available with this bus type. Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> --- drivers/media/platform/stm32/stm32-dcmi.c | 37 +++++++++++++++++++++++++++++-- 1 file changed, 35 insertions(+), 2 deletions(-)