diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
index 9f4e3824e71e..56c1dc8f92bc 100644
--- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
@@ -9,6 +9,7 @@ document for it just like any other devices.
 
 Compatible		Vendor / Chip
 ==========		=============
+abcn,abb5zes3		AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface
 ad,ad7414		SMBus/I2C Digital Temperature Sensor in 6-Pin SOT with SMBus Alert and Over Temperature Pin
 ad,adm9240		ADM9240:  Complete System Hardware Monitor for uProcessor-Based Systems
 adi,adt7461		+/-1C TDM Extended Temp Range I.C
diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index f15cddfeb897..1b19f327f35f 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -153,6 +153,17 @@ config RTC_DRV_88PM80X
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-88pm80x.
 
+config RTC_DRV_ABB5ZES3
+       depends on I2C
+       select REGMAP_I2C
+       tristate "Abracon AB-RTCMC-32.768kHz-B5ZE-S3"
+       help
+	  If you say yes here you get support for the Abracon
+	  AB-RTCMC-32.768kHz-B5ZE-S3 I2C RTC chip.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called rtc-ab-b5ze-s3.
+
 config RTC_DRV_AS3722
 	tristate "ams AS3722 RTC driver"
 	depends on MFD_AS3722
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index c8ef3e1e6ccd..855c4e364058 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -24,6 +24,7 @@ obj-$(CONFIG_RTC_DRV_88PM860X)  += rtc-88pm860x.o
 obj-$(CONFIG_RTC_DRV_88PM80X)	+= rtc-88pm80x.o
 obj-$(CONFIG_RTC_DRV_AB3100)	+= rtc-ab3100.o
 obj-$(CONFIG_RTC_DRV_AB8500)	+= rtc-ab8500.o
+obj-$(CONFIG_RTC_DRV_ABB5ZES3)	+= rtc-ab-b5ze-s3.o
 obj-$(CONFIG_RTC_DRV_AS3722)	+= rtc-as3722.o
 obj-$(CONFIG_RTC_DRV_AT32AP700X)+= rtc-at32ap700x.o
 obj-$(CONFIG_RTC_DRV_AT91RM9200)+= rtc-at91rm9200.o
diff --git a/drivers/rtc/rtc-ab-b5ze-s3.c b/drivers/rtc/rtc-ab-b5ze-s3.c
new file mode 100644
index 000000000000..6b73051cfef7
--- /dev/null
+++ b/drivers/rtc/rtc-ab-b5ze-s3.c
@@ -0,0 +1,792 @@
+/*
+ * rtc-ab-b5ze-s3 - Driver for Abracon AB-RTCMC-32.768Khz-B5ZE-S3
+ *                  I2C RTC / Alarm chip
+ *
+ * Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * Detailed datasheet of the chip is available here:
+ *
+ *  http://www.abracon.com/realtimeclock/AB-RTCMC-32.768kHz-B5ZE-S3-Application-Manual.pdf
+ *
+ * This work is based on ISL12057 driver (drivers/rtc/rtc-isl12057.c).
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/rtc.h>
+#include <linux/i2c.h>
+#include <linux/bcd.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/interrupt.h>
+
+#define DRV_NAME "rtc-ab-b5ze-s3"
+
+/* Control section */
+#define ABB5ZES3_REG_CTRL1	   0x00	   /* Control 1 register */
+#define ABB5ZES3_REG_CTRL1_CIE	   BIT(0)  /* Pulse interrupt enable */
+#define ABB5ZES3_REG_CTRL1_AIE	   BIT(1)  /* Alarm interrupt enable */
+#define ABB5ZES3_REG_CTRL1_SIE	   BIT(2)  /* Second interrupt enable */
+#define ABB5ZES3_REG_CTRL1_PM	   BIT(3)  /* 24h/12h mode */
+#define ABB5ZES3_REG_CTRL1_SR	   BIT(4)  /* Software reset */
+#define ABB5ZES3_REG_CTRL1_STOP	   BIT(5)  /* RTC circuit enable */
+#define ABB5ZES3_REG_CTRL1_CAP	   BIT(7)
+
+#define ABB5ZES3_REG_CTRL2	   0x01	   /* Control 2 register */
+#define ABB5ZES3_REG_CTRL2_CTBIE   BIT(0)  /* Countdown timer B int. enable */
+#define ABB5ZES3_REG_CTRL2_CTAIE   BIT(1)  /* Countdown timer A int. enable */
+#define ABB5ZES3_REG_CTRL2_WTAIE   BIT(2)  /* Watchdog timer A int. enable */
+#define ABB5ZES3_REG_CTRL2_AF	   BIT(3)  /* Alarm interrupt status */
+#define ABB5ZES3_REG_CTRL2_SF	   BIT(4)  /* Second interrupt status */
+#define ABB5ZES3_REG_CTRL2_CTBF	   BIT(5)  /* Countdown timer B int. status */
+#define ABB5ZES3_REG_CTRL2_CTAF	   BIT(6)  /* Countdown timer A int. status */
+#define ABB5ZES3_REG_CTRL2_WTAF	   BIT(7)  /* Watchdog timer A int. status */
+
+#define ABB5ZES3_REG_CTRL3	   0x02	   /* Control 3 register */
+#define ABB5ZES3_REG_CTRL3_PM2	   BIT(7)  /* Power Management bit 2 */
+#define ABB5ZES3_REG_CTRL3_PM1	   BIT(6)  /* Power Management bit 1 */
+#define ABB5ZES3_REG_CTRL3_PM0	   BIT(5)  /* Power Management bit 0 */
+#define ABB5ZES3_REG_CTRL3_BSF	   BIT(3)  /* Battery switchover int. status */
+#define ABB5ZES3_REG_CTRL3_BLF	   BIT(2)  /* Battery low int. status */
+#define ABB5ZES3_REG_CTRL3_BSIE	   BIT(1)  /* Battery switchover int. enable */
+#define ABB5ZES3_REG_CTRL3_BLIE	   BIT(0)  /* Battery low int. enable */
+
+#define ABB5ZES3_CTRL_SEC_LEN	   3
+
+/* RTC section */
+#define ABB5ZES3_REG_RTC_SC	   0x03	   /* RTC Seconds register */
+#define ABB5ZES3_REG_RTC_SC_OSC	   BIT(7)  /* Clock integrity status */
+#define ABB5ZES3_REG_RTC_MN	   0x04	   /* RTC Minutes register */
+#define ABB5ZES3_REG_RTC_HR	   0x05	   /* RTC Hours register */
+#define ABB5ZES3_REG_RTC_HR_PM	   BIT(5)  /* RTC Hours PM bit */
+#define ABB5ZES3_REG_RTC_DT	   0x06	   /* RTC Date register */
+#define ABB5ZES3_REG_RTC_DW	   0x07	   /* RTC Day of the week register */
+#define ABB5ZES3_REG_RTC_MO	   0x08	   /* RTC Month register */
+#define ABB5ZES3_REG_RTC_YR	   0x09	   /* RTC Year register */
+
+#define ABB5ZES3_RTC_SEC_LEN	   7
+
+/* Alarm section (enable bits are all active low) */
+#define ABB5ZES3_REG_ALRM_MN	   0x0A	   /* Alarm - minute register */
+#define ABB5ZES3_REG_ALRM_MN_AE	   BIT(7)  /* Minute enable */
+#define ABB5ZES3_REG_ALRM_HR	   0x0B	   /* Alarm - hours register */
+#define ABB5ZES3_REG_ALRM_HR_AE	   BIT(7)  /* Hour enable */
+#define ABB5ZES3_REG_ALRM_DT	   0x0C	   /* Alarm - date register */
+#define ABB5ZES3_REG_ALRM_DT_AE	   BIT(7)  /* Date (day of the month) enable */
+#define ABB5ZES3_REG_ALRM_DW	   0x0D	   /* Alarm - day of the week reg. */
+#define ABB5ZES3_REG_ALRM_DW_AE	   BIT(7)  /* Day of the week enable */
+
+#define ABB5ZES3_ALRM_SEC_LEN	   4
+
+/* Frequency offset section */
+#define ABB5ZES3_REG_FREQ_OF	   0x0E	   /* Frequency offset register */
+#define ABB5ZES3_REG_FREQ_OF_MODE  0x0E	   /* Offset mode: 2 hours / minute */
+
+/* CLOCKOUT section */
+#define ABB5ZES3_REG_TIM_CLK	   0x0F	   /* Timer & Clockout register */
+#define ABB5ZES3_REG_TIM_CLK_TAM   BIT(7)  /* Permanent/pulsed timer A/int. 2 */
+#define ABB5ZES3_REG_TIM_CLK_TBM   BIT(6)  /* Permanent/pulsed timer B */
+#define ABB5ZES3_REG_TIM_CLK_COF2  BIT(5)  /* Clkout Freq bit 2 */
+#define ABB5ZES3_REG_TIM_CLK_COF1  BIT(4)  /* Clkout Freq bit 1 */
+#define ABB5ZES3_REG_TIM_CLK_COF0  BIT(3)  /* Clkout Freq bit 0 */
+#define ABB5ZES3_REG_TIM_CLK_TAC1  BIT(2)  /* Timer A: - 01 : countdown */
+#define ABB5ZES3_REG_TIM_CLK_TAC0  BIT(1)  /*	       - 10 : timer	*/
+#define ABB5ZES3_REG_TIM_CLK_TBC   BIT(0)  /* Timer B enable */
+
+/* Timer A Section */
+#define ABB5ZES3_REG_TIMA_CLK	   0x10	   /* Timer A clock register */
+#define ABB5ZES3_REG_TIMA_CLK_TAQ2 BIT(2)  /* Freq bit 2 */
+#define ABB5ZES3_REG_TIMA_CLK_TAQ1 BIT(1)  /* Freq bit 1 */
+#define ABB5ZES3_REG_TIMA_CLK_TAQ0 BIT(0)  /* Freq bit 0 */
+#define ABB5ZES3_REG_TIMA	   0x11	   /* Timer A register */
+
+#define ABB5ZES3_TIMA_SEC_LEN	   2
+
+/* Timer B Section */
+#define ABB5ZES3_REG_TIMB_CLK	   0x12	   /* Timer B clock register */
+#define ABB5ZES3_REG_TIMB_CLK_TBW2 BIT(6)
+#define ABB5ZES3_REG_TIMB_CLK_TBW1 BIT(5)
+#define ABB5ZES3_REG_TIMB_CLK_TBW0 BIT(4)
+#define ABB5ZES3_REG_TIMB_CLK_TAQ2 BIT(2)
+#define ABB5ZES3_REG_TIMB_CLK_TAQ1 BIT(1)
+#define ABB5ZES3_REG_TIMB_CLK_TAQ0 BIT(0)
+#define ABB5ZES3_REG_TIMB	   0x13	   /* Timer B register */
+#define ABB5ZES3_TIMB_SEC_LEN	   2
+
+#define ABB5ZES3_MEM_MAP_LEN	   0x14
+
+struct abb5zes3_rtc_data {
+	struct rtc_device *rtc;
+	struct regmap *regmap;
+	struct mutex lock;
+
+	int irq;
+
+	bool battery_low;
+};
+
+/*
+ * Try and match register bits w/ fixed null values to see whether we
+ * are dealing with an ABB5ZES3. Note: this function is called early
+ * during init and hence does need mutex protection.
+ */
+static int abb5zes3_i2c_validate_chip(struct regmap *regmap)
+{
+	u8 regs[ABB5ZES3_MEM_MAP_LEN];
+	static const u8 mask[ABB5ZES3_MEM_MAP_LEN] = { 0x00, 0x00, 0x10, 0x00,
+						       0x80, 0xc0, 0xc0, 0xf8,
+						       0xe0, 0x00, 0x00, 0x40,
+						       0x40, 0x78, 0x00, 0x00,
+						       0xf8, 0x00, 0x88, 0x00 };
+	int ret, i;
+
+	ret = regmap_bulk_read(regmap, 0, regs, ABB5ZES3_MEM_MAP_LEN);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < ABB5ZES3_MEM_MAP_LEN; ++i) {
+		if (regs[i] & mask[i]) /* check if bits are cleared */
+			return -ENODEV;
+	}
+
+	return 0;
+}
+
+/* Clear alarm status bit. */
+static int _abb5zes3_rtc_clear_alarm(struct device *dev)
+{
+	struct abb5zes3_rtc_data *data = dev_get_drvdata(dev);
+	int ret;
+
+	ret = regmap_update_bits(data->regmap, ABB5ZES3_REG_CTRL2,
+				 ABB5ZES3_REG_CTRL2_AF, 0);
+	if (ret)
+		dev_err(dev, "%s: clearing alarm failed (%d)\n", __func__, ret);
+
+	return ret;
+}
+
+/* Enable or disable alarm (i.e. alarm interrupt generation) */
+static int _abb5zes3_rtc_update_alarm(struct device *dev, bool enable)
+{
+	struct abb5zes3_rtc_data *data = dev_get_drvdata(dev);
+	int ret;
+
+	ret = regmap_update_bits(data->regmap, ABB5ZES3_REG_CTRL1,
+				 ABB5ZES3_REG_CTRL1_AIE,
+				 enable ? ABB5ZES3_REG_CTRL1_AIE : 0);
+	if (ret)
+		dev_err(dev, "%s: writing alarm INT failed (%d)\n",
+			__func__, ret);
+
+	return ret;
+}
+
+/*
+ * Note: we only read, so regmap inner lock protection is sufficient, i.e.
+ * we do not need driver's main lock protection.
+ */
+static int _abb5zes3_rtc_read_time(struct device *dev, struct rtc_time *tm)
+{
+	struct abb5zes3_rtc_data *data = dev_get_drvdata(dev);
+	u8 regs[ABB5ZES3_REG_RTC_SC + ABB5ZES3_RTC_SEC_LEN];
+	int ret;
+
+	/*
+	 * As we need to read CTRL1 register anyway to access 24/12h
+	 * mode bit, we do a single bulk read of both control and RTC
+	 * sections (they are consecutive). This also ease indexing
+	 * of register values after bulk read.
+	 */
+	ret = regmap_bulk_read(data->regmap, ABB5ZES3_REG_CTRL1, regs,
+			       sizeof(regs));
+	if (ret) {
+		dev_err(dev, "%s: reading RTC time failed (%d)\n",
+			__func__, ret);
+		goto err;
+	}
+
+	/* If clock integrity is not guaranteed, do not return a time value */
+	if (regs[ABB5ZES3_REG_RTC_SC] & ABB5ZES3_REG_RTC_SC_OSC) {
+		ret = -ENODATA;
+		goto err;
+	}
+
+	tm->tm_sec = bcd2bin(regs[ABB5ZES3_REG_RTC_SC] & 0x7F);
+	tm->tm_min = bcd2bin(regs[ABB5ZES3_REG_RTC_MN]);
+
+	if (regs[ABB5ZES3_REG_CTRL1] & ABB5ZES3_REG_CTRL1_PM) { /* 12hr mode */
+		tm->tm_hour = bcd2bin(regs[ABB5ZES3_REG_RTC_HR] & 0x1f);
+		if (regs[ABB5ZES3_REG_RTC_HR] & ABB5ZES3_REG_RTC_HR_PM) /* PM */
+			tm->tm_hour += 12;
+	} else {						/* 24hr mode */
+		tm->tm_hour = bcd2bin(regs[ABB5ZES3_REG_RTC_HR]);
+	}
+
+	tm->tm_mday = bcd2bin(regs[ABB5ZES3_REG_RTC_DT]);
+	tm->tm_wday = bcd2bin(regs[ABB5ZES3_REG_RTC_DW]);
+	tm->tm_mon  = bcd2bin(regs[ABB5ZES3_REG_RTC_MO]) - 1; /* starts at 1 */
+	tm->tm_year = bcd2bin(regs[ABB5ZES3_REG_RTC_YR]) + 100;
+
+	ret = rtc_valid_tm(tm);
+
+err:
+	return ret;
+}
+
+static int abb5zes3_rtc_set_time(struct device *dev, struct rtc_time *tm)
+{
+	struct abb5zes3_rtc_data *data = dev_get_drvdata(dev);
+	u8 regs[ABB5ZES3_REG_RTC_SC + ABB5ZES3_RTC_SEC_LEN];
+	int ret;
+
+	/*
+	 * Year register is 8-bit wide and bcd-coded, i.e records values
+	 * between 0 and 99. tm_year is an offset from 1900 and we are
+	 * interested in the 2000-2099 range, so any value less than 100
+	 * is invalid.
+	 */
+	if (tm->tm_year < 100)
+		return -EINVAL;
+
+	regs[ABB5ZES3_REG_RTC_SC] = bin2bcd(tm->tm_sec); /* MSB=0 clears OSC */
+	regs[ABB5ZES3_REG_RTC_MN] = bin2bcd(tm->tm_min);
+	regs[ABB5ZES3_REG_RTC_HR] = bin2bcd(tm->tm_hour); /* 24-hour format */
+	regs[ABB5ZES3_REG_RTC_DT] = bin2bcd(tm->tm_mday);
+	regs[ABB5ZES3_REG_RTC_DW] = bin2bcd(tm->tm_wday);
+	regs[ABB5ZES3_REG_RTC_MO] = bin2bcd(tm->tm_mon + 1);
+	regs[ABB5ZES3_REG_RTC_YR] = bin2bcd(tm->tm_year - 100);
+
+	mutex_lock(&data->lock);
+	ret = regmap_bulk_write(data->regmap, ABB5ZES3_REG_RTC_SC,
+				regs + ABB5ZES3_REG_RTC_SC,
+				ABB5ZES3_RTC_SEC_LEN);
+	mutex_unlock(&data->lock);
+
+
+	return ret;
+}
+
+static int abb5zes3_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alarm)
+{
+	struct abb5zes3_rtc_data *data = dev_get_drvdata(dev);
+	struct rtc_time rtc_tm, *alarm_tm = &alarm->time;
+	unsigned long rtc_secs, alarm_secs;
+	u8 regs[ABB5ZES3_ALRM_SEC_LEN];
+	unsigned int reg;
+	int ret;
+
+	mutex_lock(&data->lock);
+	ret = regmap_bulk_read(data->regmap, ABB5ZES3_REG_ALRM_MN, regs,
+			       ABB5ZES3_ALRM_SEC_LEN);
+	if (ret) {
+		dev_err(dev, "%s: reading alarm section failed (%d)\n",
+			__func__, ret);
+		goto err;
+	}
+
+	alarm_tm->tm_sec  = 0;
+	alarm_tm->tm_min  = bcd2bin(regs[0] & 0x7f);
+	alarm_tm->tm_hour = bcd2bin(regs[1] & 0x3f);
+	alarm_tm->tm_mday = bcd2bin(regs[2] & 0x3f);
+	alarm_tm->tm_wday = -1;
+
+	/*
+	 * The alarm section does not store year/month. We use the ones in rtc
+	 * section as a basis and increment month and then year if needed to get
+	 * alarm after current time.
+	 */
+	ret = _abb5zes3_rtc_read_time(dev, &rtc_tm);
+	if (ret)
+		goto err;
+
+	alarm_tm->tm_year = rtc_tm.tm_year;
+	alarm_tm->tm_mon = rtc_tm.tm_mon;
+
+	ret = rtc_tm_to_time(&rtc_tm, &rtc_secs);
+	if (ret)
+		goto err;
+
+	ret = rtc_tm_to_time(alarm_tm, &alarm_secs);
+	if (ret)
+		goto err;
+
+	if (alarm_secs < rtc_secs) {
+		if (alarm_tm->tm_mon == 11) {
+			alarm_tm->tm_mon = 0;
+			alarm_tm->tm_year += 1;
+		} else {
+			alarm_tm->tm_mon += 1;
+		}
+	}
+
+	ret = regmap_read(data->regmap, ABB5ZES3_REG_CTRL1, &reg);
+	if (ret) {
+		dev_err(dev, "%s: reading ctrl reg failed (%d)\n",
+			__func__, ret);
+		goto err;
+	}
+
+	alarm->enabled = !!(reg & ABB5ZES3_REG_CTRL1_AIE);
+
+err:
+	mutex_unlock(&data->lock);
+
+	return ret;
+}
+
+/* ALARM is only accurate to the minute (not the second) */
+static int abb5zes3_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alarm)
+{
+	struct abb5zes3_rtc_data *data = dev_get_drvdata(dev);
+	struct rtc_time *alarm_tm = &alarm->time;
+	unsigned long rtc_secs, alarm_secs;
+	u8 regs[ABB5ZES3_ALRM_SEC_LEN];
+	struct rtc_time rtc_tm;
+	int ret, enable = 1;
+
+	mutex_lock(&data->lock);
+	ret = _abb5zes3_rtc_read_time(dev, &rtc_tm);
+	if (ret)
+		goto err;
+
+	ret = rtc_tm_to_time(&rtc_tm, &rtc_secs);
+	if (ret)
+		goto err;
+
+	ret = rtc_tm_to_time(alarm_tm, &alarm_secs);
+	if (ret)
+		goto err;
+
+	/* If alarm time is before current time, disable the alarm */
+	if (!alarm->enabled || alarm_secs <= rtc_secs) {
+		enable = 0;
+	} else {
+		/*
+		 * Chip only support alarms up to one month in the future. Let's
+		 * return an error if we get something after that limit.
+		 * Comparison is done by incrementing rtc_tm month field by one
+		 * and checking alarm value is still below.
+		 */
+		if (rtc_tm.tm_mon == 11) { /* handle year wrapping */
+			rtc_tm.tm_mon = 0;
+			rtc_tm.tm_year += 1;
+		} else {
+			rtc_tm.tm_mon += 1;
+		}
+
+		ret = rtc_tm_to_time(&rtc_tm, &rtc_secs);
+		if (ret)
+			goto err;
+
+		if (alarm_secs > rtc_secs) {
+			dev_err(dev, "%s: alarm maximum is one month in the "
+				"future (%d)\n", __func__, ret);
+			ret = -EINVAL;
+			goto err;
+		}
+	}
+
+	/* Disable the alarm before modifying it */
+	ret = _abb5zes3_rtc_update_alarm(dev, 0);
+	if (ret < 0) {
+		dev_err(dev, "%s: unable to disable the alarm (%d)\n",
+			__func__, ret);
+		goto err;
+	}
+
+	/* Program alarm registers */
+	regs[0] = bin2bcd(alarm_tm->tm_min) & 0x7f;  /* minute */
+	regs[1] = bin2bcd(alarm_tm->tm_hour) & 0x3f; /* hour */
+	regs[2] = bin2bcd(alarm_tm->tm_mday) & 0x3f; /* day of the month */
+	regs[3] = ABB5ZES3_REG_ALRM_DW_AE; /* do not match day of the week */
+
+	ret = regmap_bulk_write(data->regmap, ABB5ZES3_REG_ALRM_MN, regs,
+				ABB5ZES3_ALRM_SEC_LEN);
+	if (ret < 0) {
+		dev_err(dev, "%s: writing ALARM section failed (%d)\n",
+			__func__, ret);
+		goto err;
+	}
+
+	/* Enable or disable alarm */
+	ret = _abb5zes3_rtc_update_alarm(dev, enable);
+
+err:
+	mutex_unlock(&data->lock);
+
+	return ret;
+}
+
+
+/* Enable or disable battery low irq generation */
+static inline int _abb5zes3_rtc_battery_low_irq_enable(struct regmap *regmap,
+						       bool enable)
+{
+	return regmap_update_bits(regmap, ABB5ZES3_REG_CTRL3,
+				  ABB5ZES3_REG_CTRL3_BLIE,
+				  enable ? ABB5ZES3_REG_CTRL3_BLIE : 0);
+}
+
+/*
+ * Check current RTC status and enable/disable what needs to be. Return 0 if
+ * everything went ok and a negative value upon error. Note: this function
+ * is called early during init and hence does need mutex protection.
+ */
+static int abb5zes3_rtc_check_setup(struct device *dev)
+{
+	struct abb5zes3_rtc_data *data = dev_get_drvdata(dev);
+	struct regmap *regmap =  data->regmap;
+	unsigned int reg;
+	int ret;
+	u8 mask;
+
+	/*
+	 * By default, the devices generates a 32.768KHz signal on IRQ#1 pin. It
+	 * is disabled here to prevent polluting the interrupt line and
+	 * uselessly triggering the IRQ handler we install for alarm and battery
+	 * low events. Note: this is done before clearing int. status below
+	 * in this function.
+	 * We also disable all timers and set timer interrupt to permanent (not
+	 * pulsed).
+	 */
+	mask = (ABB5ZES3_REG_TIM_CLK_TBC | ABB5ZES3_REG_TIM_CLK_TAC0 |
+		ABB5ZES3_REG_TIM_CLK_TAC1 | ABB5ZES3_REG_TIM_CLK_COF0 |
+		ABB5ZES3_REG_TIM_CLK_COF1 | ABB5ZES3_REG_TIM_CLK_COF2 |
+		ABB5ZES3_REG_TIM_CLK_TBM | ABB5ZES3_REG_TIM_CLK_TAM);
+	ret = regmap_update_bits(regmap, ABB5ZES3_REG_TIM_CLK, mask,
+		ABB5ZES3_REG_TIM_CLK_COF0 | ABB5ZES3_REG_TIM_CLK_COF1 |
+		ABB5ZES3_REG_TIM_CLK_COF2);
+	if (ret < 0) {
+		dev_err(dev, "%s: unable to initialize clkout register (%d)\n",
+			__func__, ret);
+		return ret;
+	}
+
+	/*
+	 * Each component of the alarm (MN, HR, DT, DW) can be enabled/disabled
+	 * individually by clearing/setting MSB of each associated register. So,
+	 * we set all alarm enable bits to disable current alarm setting.
+	 */
+	mask = (ABB5ZES3_REG_ALRM_MN_AE | ABB5ZES3_REG_ALRM_HR_AE |
+		ABB5ZES3_REG_ALRM_DT_AE | ABB5ZES3_REG_ALRM_DW_AE);
+	ret = regmap_update_bits(regmap, ABB5ZES3_REG_CTRL2, mask, mask);
+	if (ret < 0) {
+		dev_err(dev, "%s: unable to disable alarm setting (%d)\n",
+			__func__, ret);
+		return ret;
+	}
+
+	/* Set Control 1 register (RTC enabled, 24hr mode, all int. disabled) */
+	mask = (ABB5ZES3_REG_CTRL1_CIE | ABB5ZES3_REG_CTRL1_AIE |
+		ABB5ZES3_REG_CTRL1_SIE | ABB5ZES3_REG_CTRL1_PM |
+		ABB5ZES3_REG_CTRL1_CAP | ABB5ZES3_REG_CTRL1_STOP);
+	ret = regmap_update_bits(regmap, ABB5ZES3_REG_CTRL1, mask, 0);
+	if (ret < 0) {
+		dev_err(dev, "%s: unable to initialize CTRL1 register (%d)\n",
+			__func__, ret);
+		return ret;
+	}
+
+	/*
+	 * Set Control 2 register (timer int. disabled, alarm status cleared).
+	 * WTAF is read-only and cleared automatically by reading the register.
+	 */
+	mask = (ABB5ZES3_REG_CTRL2_CTBIE | ABB5ZES3_REG_CTRL2_CTAIE |
+		ABB5ZES3_REG_CTRL2_WTAIE | ABB5ZES3_REG_CTRL2_AF |
+		ABB5ZES3_REG_CTRL2_SF | ABB5ZES3_REG_CTRL2_CTBF |
+		ABB5ZES3_REG_CTRL2_CTAF);
+	ret = regmap_update_bits(regmap, ABB5ZES3_REG_CTRL2, mask, 0);
+	if (ret < 0) {
+		dev_err(dev, "%s: unable to initialize CTRL2 register (%d)\n",
+			__func__, ret);
+		return ret;
+	}
+
+	/*
+	 * Enable battery low detection function and battery switchover function
+	 * (standard mode). Disable associated interrupts. Clear battery
+	 * switchover flag but not battery low flag. The latter is checked
+	 * later below.
+	 */
+	mask = (ABB5ZES3_REG_CTRL3_PM0 | ABB5ZES3_REG_CTRL3_PM1 |
+		ABB5ZES3_REG_CTRL3_PM2 | ABB5ZES3_REG_CTRL3_BLIE |
+		ABB5ZES3_REG_CTRL3_BSIE| ABB5ZES3_REG_CTRL3_BSF);
+	ret = regmap_update_bits(regmap, ABB5ZES3_REG_CTRL3, mask, 0);
+	if (ret < 0) {
+		dev_err(dev, "%s: unable to initialize CTRL3 register (%d)\n",
+			__func__, ret);
+		return ret;
+	}
+
+	/* Check oscillator integrity flag */
+	ret = regmap_read(regmap, ABB5ZES3_REG_RTC_SC, &reg);
+	if (ret < 0) {
+		dev_err(dev, "%s: unable to read osc. integrity flag (%d)\n",
+			__func__, ret);
+		return ret;
+	}
+
+	if (reg & ABB5ZES3_REG_RTC_SC_OSC) {
+		dev_err(dev, "clock integrity not guaranteed. Osc. has stopped "
+			"or has been interrupted.\n");
+		dev_err(dev, "change battery (if not already done) and  "
+			"then set time to reset osc. failure flag.\n");
+	}
+
+	/*
+	 * Check battery low flag at startup: this allows reporting battery
+	 * is low at startup when IRQ line is not connected. Note: we record
+	 * current status to avoid reenabling this interrupt later in probe
+	 * function if battery is low.
+	 */
+	ret = regmap_read(regmap, ABB5ZES3_REG_CTRL3, &reg);
+	if (ret < 0) {
+		dev_err(dev, "%s: unable to read battery low flag (%d)\n",
+			__func__, ret);
+		return ret;
+	}
+
+	data->battery_low = reg & ABB5ZES3_REG_CTRL3_BLF;
+	if (data->battery_low) {
+		dev_err(dev, "RTC battery is low; please, consider "
+			"changing it!\n");
+
+		ret = _abb5zes3_rtc_battery_low_irq_enable(regmap, false);
+		if (ret)
+			dev_err(dev, "%s: disabling battery low interrupt "
+				"generation failed (%d)\n", __func__, ret);
+	}
+
+	return ret;
+}
+
+static int abb5zes3_rtc_alarm_irq_enable(struct device *dev,
+					 unsigned int enable)
+{
+	struct abb5zes3_rtc_data *rtc_data = dev_get_drvdata(dev);
+	int ret = 0;
+
+	if (rtc_data->irq) {
+		mutex_lock(&rtc_data->lock);
+		ret = _abb5zes3_rtc_update_alarm(dev, enable);
+		mutex_unlock(&rtc_data->lock);
+	}
+
+	return ret;
+}
+
+static irqreturn_t _abb5zes3_rtc_interrupt(int irq, void *data)
+{
+	struct i2c_client *client = data;
+	struct device *dev = &client->dev;
+	struct abb5zes3_rtc_data *rtc_data = dev_get_drvdata(dev);
+	struct rtc_device *rtc = rtc_data->rtc;
+	u8 regs[ABB5ZES3_CTRL_SEC_LEN];
+	int ret, handled = IRQ_NONE;
+
+	ret = regmap_bulk_read(rtc_data->regmap, 0, regs,
+			       ABB5ZES3_CTRL_SEC_LEN);
+	if (ret) {
+		dev_err(dev, "%s: unable to read control section (%d)!\n",
+			__func__, ret);
+		return handled;
+	}
+
+	/*
+	 * Check battery low detection flag and disable battery low interrupt
+	 * generation if flag is set (interrupt can only be cleared when
+	 * battery is replaced).
+	 */
+	if (regs[ABB5ZES3_REG_CTRL3] & ABB5ZES3_REG_CTRL3_BLF) {
+		dev_err(dev, "RTC battery is low; please change it!\n");
+
+		_abb5zes3_rtc_battery_low_irq_enable(rtc_data->regmap, false);
+
+		handled = IRQ_HANDLED;
+	}
+
+	/* Check alarm flag */
+	if (regs[ABB5ZES3_REG_CTRL2] & ABB5ZES3_REG_CTRL2_AF) {
+		dev_dbg(dev, "RTC alarm!\n");
+
+		rtc_update_irq(rtc, 1, RTC_IRQF | RTC_AF);
+
+		/* Acknowledge and disable the alarm */
+		_abb5zes3_rtc_clear_alarm(dev);
+		_abb5zes3_rtc_update_alarm(dev, 0);
+
+		handled = IRQ_HANDLED;
+	}
+
+	return handled;
+}
+
+static const struct rtc_class_ops rtc_ops = {
+	.read_time = _abb5zes3_rtc_read_time,
+	.set_time = abb5zes3_rtc_set_time,
+	.read_alarm = abb5zes3_rtc_read_alarm,
+	.set_alarm = abb5zes3_rtc_set_alarm,
+	.alarm_irq_enable = abb5zes3_rtc_alarm_irq_enable,
+};
+
+static struct regmap_config abb5zes3_rtc_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+};
+
+static int abb5zes3_probe(struct i2c_client *client,
+			  const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct abb5zes3_rtc_data *data;
+	struct regmap *regmap;
+	int ret;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C |
+				     I2C_FUNC_SMBUS_BYTE_DATA |
+				     I2C_FUNC_SMBUS_I2C_BLOCK))
+		return -ENODEV;
+
+	regmap = devm_regmap_init_i2c(client, &abb5zes3_rtc_regmap_config);
+	if (IS_ERR(regmap)) {
+		ret = PTR_ERR(regmap);
+		dev_err(dev, "%s: regmap allocation failed: %d\n",
+			__func__, ret);
+		return ret;
+	}
+
+	ret = abb5zes3_i2c_validate_chip(regmap);
+	if (ret)
+		return ret;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	mutex_init(&data->lock);
+	data->regmap = regmap;
+	dev_set_drvdata(dev, data);
+
+	ret = abb5zes3_rtc_check_setup(dev);
+	if (ret)
+		return ret;
+
+	if (client->irq > 0) {
+		ret = devm_request_threaded_irq(dev, client->irq, NULL,
+						_abb5zes3_rtc_interrupt,
+						IRQF_SHARED|IRQF_ONESHOT,
+						DRV_NAME, client);
+		if (!ret) {
+			device_init_wakeup(dev, true);
+			data->irq = client->irq;
+			dev_dbg(dev, "%s: irq %d used by RTC\n", __func__,
+				client->irq);
+		} else {
+			dev_err(dev, "%s: irq %d unavailable (%d)\n",
+				__func__, client->irq, ret);
+		}
+	}
+
+	data->rtc = devm_rtc_device_register(dev, DRV_NAME, &rtc_ops,
+					     THIS_MODULE);
+	ret = PTR_ERR_OR_ZERO(data->rtc);
+	if (ret) {
+		dev_err(dev, "%s: unable to register RTC device (%d)\n",
+			__func__, ret);
+		device_init_wakeup(dev, false);
+	}
+
+	/*
+	 * AB-B5Z5E only supports a coarse granularity alarm (one minute
+	 * resolution up to one month) so we cannot support UIE mode
+	 * using the device's alarm. Note it should be feasible to support
+	 * such a feature using one of the two timers the device provides.
+	 */
+	data->rtc->uie_unsupported = 1;
+
+	/* Enable battery low detection interrupt if battery not already low */
+	if (!data->battery_low && data->irq) {
+		ret = _abb5zes3_rtc_battery_low_irq_enable(regmap, true);
+		if (ret)
+			dev_err(dev, "%s: enabling battery low interrupt "
+				"generation failed (%d)\n", __func__, ret);
+	}
+
+	return ret;
+}
+
+static int abb5zes3_remove(struct i2c_client *client)
+{
+	struct abb5zes3_rtc_data *rtc_data = dev_get_drvdata(&client->dev);
+
+	if (rtc_data->irq > 0)
+		device_init_wakeup(&client->dev, false);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int abb5zes3_rtc_suspend(struct device *dev)
+{
+	struct abb5zes3_rtc_data *rtc_data = dev_get_drvdata(dev);
+
+	if (device_may_wakeup(dev))
+		return enable_irq_wake(rtc_data->irq);
+
+	return 0;
+}
+
+static int abb5zes3_rtc_resume(struct device *dev)
+{
+	struct abb5zes3_rtc_data *rtc_data = dev_get_drvdata(dev);
+
+	if (device_may_wakeup(dev))
+		return disable_irq_wake(rtc_data->irq);
+
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(abb5zes3_rtc_pm_ops, abb5zes3_rtc_suspend,
+			 abb5zes3_rtc_resume);
+
+#ifdef CONFIG_OF
+static const struct of_device_id abb5zes3_dt_match[] = {
+	{ .compatible = "abcn,abb5zes3" },
+	{ },
+};
+#endif
+
+static const struct i2c_device_id abb5zes3_id[] = {
+	{ "abb5zes3", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, abb5zes3_id);
+
+static struct i2c_driver abb5zes3_driver = {
+	.driver = {
+		.name = DRV_NAME,
+		.owner = THIS_MODULE,
+		.pm = &abb5zes3_rtc_pm_ops,
+		.of_match_table = of_match_ptr(abb5zes3_dt_match),
+	},
+	.probe	  = abb5zes3_probe,
+	.remove	  = abb5zes3_remove,
+	.id_table = abb5zes3_id,
+};
+module_i2c_driver(abb5zes3_driver);
+
+MODULE_AUTHOR("Arnaud EBALARD <arno@natisbad.org>");
+MODULE_DESCRIPTION("Abracon AB-RTCMC-32.768kHz-B5ZE-S3 RTC/Alarm driver");
+MODULE_LICENSE("GPL");
