diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index 4b6de70..6f496df 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -30,7 +30,7 @@
 #include <plat/tc.h>
 #include <mach/mux.h>
 #include <mach/flash.h>
-#include <plat/fpga.h>
+#include <../plat-omap/fpga.h>
 #include <linux/platform_data/keypad-omap.h>
 
 #include <mach/hardware.h>
@@ -123,9 +123,9 @@ static struct resource smc91x_resources[] = {
 
 static void __init fsample_init_smc91x(void)
 {
-	fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
+	__raw_writeb(1, H2P2_DBG_FPGA_LAN_RESET);
 	mdelay(50);
-	fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
+	__raw_writeb(__raw_readb(H2P2_DBG_FPGA_LAN_RESET) & ~1,
 		   H2P2_DBG_FPGA_LAN_RESET);
 	mdelay(50);
 }
diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c
index db5f7d2..5804da7 100644
--- a/arch/arm/mach-omap1/board-innovator.c
+++ b/arch/arm/mach-omap1/board-innovator.c
@@ -33,7 +33,7 @@
 
 #include <mach/mux.h>
 #include <mach/flash.h>
-#include <plat/fpga.h>
+#include <../plat-omap/fpga.h>
 #include <plat/tc.h>
 #include <linux/platform_data/keypad-omap.h>
 #include <plat/mmc.h>
@@ -215,7 +215,7 @@ static struct platform_device *innovator1510_devices[] __initdata = {
 
 static int innovator_get_pendown_state(void)
 {
-	return !(fpga_read(OMAP1510_FPGA_TOUCHSCREEN) & (1 << 5));
+	return !(__raw_readb(OMAP1510_FPGA_TOUCHSCREEN) & (1 << 5));
 }
 
 static const struct ads7846_platform_data innovator1510_ts_info = {
@@ -279,7 +279,7 @@ static struct platform_device *innovator1610_devices[] __initdata = {
 static void __init innovator_init_smc91x(void)
 {
 	if (cpu_is_omap1510()) {
-		fpga_write(fpga_read(OMAP1510_FPGA_RST) & ~1,
+		__raw_writeb(__raw_readb(OMAP1510_FPGA_RST) & ~1,
 			   OMAP1510_FPGA_RST);
 		udelay(750);
 	} else {
@@ -335,10 +335,10 @@ static int mmc_set_power(struct device *dev, int slot, int power_on,
 				int vdd)
 {
 	if (power_on)
-		fpga_write(fpga_read(OMAP1510_FPGA_POWER) | (1 << 3),
+		__raw_writeb(__raw_readb(OMAP1510_FPGA_POWER) | (1 << 3),
 				OMAP1510_FPGA_POWER);
 	else
-		fpga_write(fpga_read(OMAP1510_FPGA_POWER) & ~(1 << 3),
+		__raw_writeb(__raw_readb(OMAP1510_FPGA_POWER) & ~(1 << 3),
 				OMAP1510_FPGA_POWER);
 
 	return 0;
@@ -390,14 +390,14 @@ static void __init innovator_init(void)
 		omap_cfg_reg(UART3_TX);
 		omap_cfg_reg(UART3_RX);
 
-		reg = fpga_read(OMAP1510_FPGA_POWER);
+		reg = __raw_readb(OMAP1510_FPGA_POWER);
 		reg |= OMAP1510_FPGA_PCR_COM1_EN;
-		fpga_write(reg, OMAP1510_FPGA_POWER);
+		__raw_writeb(reg, OMAP1510_FPGA_POWER);
 		udelay(10);
 
-		reg = fpga_read(OMAP1510_FPGA_POWER);
+		reg = __raw_readb(OMAP1510_FPGA_POWER);
 		reg |= OMAP1510_FPGA_PCR_COM2_EN;
-		fpga_write(reg, OMAP1510_FPGA_POWER);
+		__raw_writeb(reg, OMAP1510_FPGA_POWER);
 		udelay(10);
 
 		platform_add_devices(innovator1510_devices, ARRAY_SIZE(innovator1510_devices));
@@ -437,6 +437,7 @@ static void __init innovator_init(void)
  */
 static void __init innovator_map_io(void)
 {
+#ifdef CONFIG_ARCH_OMAP15XX
 	omap15xx_map_io();
 
 	iotable_init(innovator1510_io_desc, ARRAY_SIZE(innovator1510_io_desc));
@@ -444,9 +445,10 @@ static void __init innovator_map_io(void)
 
 	/* Dump the Innovator FPGA rev early - useful info for support. */
 	pr_debug("Innovator FPGA Rev %d.%d Board Rev %d\n",
-			fpga_read(OMAP1510_FPGA_REV_HIGH),
-			fpga_read(OMAP1510_FPGA_REV_LOW),
-			fpga_read(OMAP1510_FPGA_BOARD_REV));
+			__raw_readb(OMAP1510_FPGA_REV_HIGH),
+			__raw_readb(OMAP1510_FPGA_REV_LOW),
+			__raw_readb(OMAP1510_FPGA_BOARD_REV));
+#endif
 }
 
 MACHINE_START(OMAP_INNOVATOR, "TI-Innovator")
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index 198b054..a1cdeeb 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -30,7 +30,7 @@
 
 #include <plat/tc.h>
 #include <mach/mux.h>
-#include <plat/fpga.h>
+#include <../plat-omap/fpga.h>
 #include <mach/flash.h>
 
 #include <mach/hardware.h>
@@ -231,9 +231,9 @@ static struct omap_lcd_config perseus2_lcd_config __initdata = {
 
 static void __init perseus2_init_smc91x(void)
 {
-	fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
+	__raw_writeb(1, H2P2_DBG_FPGA_LAN_RESET);
 	mdelay(50);
-	fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
+	__raw_writeb(__raw_readb(H2P2_DBG_FPGA_LAN_RESET) & ~1,
 		   H2P2_DBG_FPGA_LAN_RESET);
 	mdelay(50);
 }
diff --git a/arch/arm/mach-omap1/common.h b/arch/arm/mach-omap1/common.h
index 9f2d8b6..26e19d3 100644
--- a/arch/arm/mach-omap1/common.h
+++ b/arch/arm/mach-omap1/common.h
@@ -41,6 +41,7 @@ static inline void omap7xx_map_io(void)
 #endif
 
 #ifdef CONFIG_ARCH_OMAP15XX
+void omap1510_fpga_init_irq(void);
 void omap15xx_map_io(void);
 #else
 static inline void omap15xx_map_io(void)
diff --git a/arch/arm/mach-omap1/fpga.c b/arch/arm/mach-omap1/fpga.c
index 29ec50f..4ec220d 100644
--- a/arch/arm/mach-omap1/fpga.c
+++ b/arch/arm/mach-omap1/fpga.c
@@ -27,7 +27,7 @@
 #include <asm/irq.h>
 #include <asm/mach/irq.h>
 
-#include <plat/fpga.h>
+#include <../plat-omap/fpga.h>
 
 #include <mach/hardware.h>
 
diff --git a/arch/arm/mach-omap1/include/mach/omap1510.h b/arch/arm/mach-omap1/include/mach/omap1510.h
index 8fe05d6..3d23524 100644
--- a/arch/arm/mach-omap1/include/mach/omap1510.h
+++ b/arch/arm/mach-omap1/include/mach/omap1510.h
@@ -45,5 +45,118 @@
 
 #define OMAP1510_DSP_MMU_BASE	(0xfffed200)
 
+/*
+ * ---------------------------------------------------------------------------
+ *  OMAP-1510 FPGA
+ * ---------------------------------------------------------------------------
+ */
+#define OMAP1510_FPGA_BASE		0xE8000000		/* VA */
+#define OMAP1510_FPGA_SIZE		SZ_4K
+#define OMAP1510_FPGA_START		0x08000000		/* PA */
+
+/* Revision */
+#define OMAP1510_FPGA_REV_LOW			IOMEM(OMAP1510_FPGA_BASE + 0x0)
+#define OMAP1510_FPGA_REV_HIGH			IOMEM(OMAP1510_FPGA_BASE + 0x1)
+#define OMAP1510_FPGA_LCD_PANEL_CONTROL		IOMEM(OMAP1510_FPGA_BASE + 0x2)
+#define OMAP1510_FPGA_LED_DIGIT			IOMEM(OMAP1510_FPGA_BASE + 0x3)
+#define INNOVATOR_FPGA_HID_SPI			IOMEM(OMAP1510_FPGA_BASE + 0x4)
+#define OMAP1510_FPGA_POWER			IOMEM(OMAP1510_FPGA_BASE + 0x5)
+
+/* Interrupt status */
+#define OMAP1510_FPGA_ISR_LO			IOMEM(OMAP1510_FPGA_BASE + 0x6)
+#define OMAP1510_FPGA_ISR_HI			IOMEM(OMAP1510_FPGA_BASE + 0x7)
+
+/* Interrupt mask */
+#define OMAP1510_FPGA_IMR_LO			IOMEM(OMAP1510_FPGA_BASE + 0x8)
+#define OMAP1510_FPGA_IMR_HI			IOMEM(OMAP1510_FPGA_BASE + 0x9)
+
+/* Reset registers */
+#define OMAP1510_FPGA_HOST_RESET		IOMEM(OMAP1510_FPGA_BASE + 0xa)
+#define OMAP1510_FPGA_RST			IOMEM(OMAP1510_FPGA_BASE + 0xb)
+
+#define OMAP1510_FPGA_AUDIO			IOMEM(OMAP1510_FPGA_BASE + 0xc)
+#define OMAP1510_FPGA_DIP			IOMEM(OMAP1510_FPGA_BASE + 0xe)
+#define OMAP1510_FPGA_FPGA_IO			IOMEM(OMAP1510_FPGA_BASE + 0xf)
+#define OMAP1510_FPGA_UART1			IOMEM(OMAP1510_FPGA_BASE + 0x14)
+#define OMAP1510_FPGA_UART2			IOMEM(OMAP1510_FPGA_BASE + 0x15)
+#define OMAP1510_FPGA_OMAP1510_STATUS		IOMEM(OMAP1510_FPGA_BASE + 0x16)
+#define OMAP1510_FPGA_BOARD_REV			IOMEM(OMAP1510_FPGA_BASE + 0x18)
+#define INNOVATOR_FPGA_CAM_USB_CONTROL		IOMEM(OMAP1510_FPGA_BASE + 0x20c)
+#define OMAP1510P1_PPT_DATA			IOMEM(OMAP1510_FPGA_BASE + 0x100)
+#define OMAP1510P1_PPT_STATUS			IOMEM(OMAP1510_FPGA_BASE + 0x101)
+#define OMAP1510P1_PPT_CONTROL			IOMEM(OMAP1510_FPGA_BASE + 0x102)
+
+#define OMAP1510_FPGA_TOUCHSCREEN		IOMEM(OMAP1510_FPGA_BASE + 0x204)
+
+#define INNOVATOR_FPGA_INFO			IOMEM(OMAP1510_FPGA_BASE + 0x205)
+#define INNOVATOR_FPGA_LCD_BRIGHT_LO		IOMEM(OMAP1510_FPGA_BASE + 0x206)
+#define INNOVATOR_FPGA_LCD_BRIGHT_HI		IOMEM(OMAP1510_FPGA_BASE + 0x207)
+#define INNOVATOR_FPGA_LED_GRN_LO		IOMEM(OMAP1510_FPGA_BASE + 0x208)
+#define INNOVATOR_FPGA_LED_GRN_HI		IOMEM(OMAP1510_FPGA_BASE + 0x209)
+#define INNOVATOR_FPGA_LED_RED_LO		IOMEM(OMAP1510_FPGA_BASE + 0x20a)
+#define INNOVATOR_FPGA_LED_RED_HI		IOMEM(OMAP1510_FPGA_BASE + 0x20b)
+#define INNOVATOR_FPGA_EXP_CONTROL		IOMEM(OMAP1510_FPGA_BASE + 0x20d)
+#define INNOVATOR_FPGA_ISR2			IOMEM(OMAP1510_FPGA_BASE + 0x20e)
+#define INNOVATOR_FPGA_IMR2			IOMEM(OMAP1510_FPGA_BASE + 0x210)
+
+#define OMAP1510_FPGA_ETHR_START		(OMAP1510_FPGA_START + 0x300)
+
+/*
+ * Power up Giga UART driver, turn on HID clock.
+ * Turn off BT power, since we're not using it and it
+ * draws power.
+ */
+#define OMAP1510_FPGA_RESET_VALUE		0x42
+
+#define OMAP1510_FPGA_PCR_IF_PD0		(1 << 7)
+#define OMAP1510_FPGA_PCR_COM2_EN		(1 << 6)
+#define OMAP1510_FPGA_PCR_COM1_EN		(1 << 5)
+#define OMAP1510_FPGA_PCR_EXP_PD0		(1 << 4)
+#define OMAP1510_FPGA_PCR_EXP_PD1		(1 << 3)
+#define OMAP1510_FPGA_PCR_48MHZ_CLK		(1 << 2)
+#define OMAP1510_FPGA_PCR_4MHZ_CLK		(1 << 1)
+#define OMAP1510_FPGA_PCR_RSRVD_BIT0		(1 << 0)
+
+/*
+ * Innovator/OMAP1510 FPGA HID register bit definitions
+ */
+#define OMAP1510_FPGA_HID_SCLK	(1<<0)	/* output */
+#define OMAP1510_FPGA_HID_MOSI	(1<<1)	/* output */
+#define OMAP1510_FPGA_HID_nSS	(1<<2)	/* output 0/1 chip idle/select */
+#define OMAP1510_FPGA_HID_nHSUS	(1<<3)	/* output 0/1 host active/suspended */
+#define OMAP1510_FPGA_HID_MISO	(1<<4)	/* input */
+#define OMAP1510_FPGA_HID_ATN	(1<<5)	/* input  0/1 chip idle/ATN */
+#define OMAP1510_FPGA_HID_rsrvd	(1<<6)
+#define OMAP1510_FPGA_HID_RESETn (1<<7)	/* output - 0/1 USAR reset/run */
+
+/* The FPGA IRQ is cascaded through GPIO_13 */
+#define OMAP1510_INT_FPGA		(IH_GPIO_BASE + 13)
+
+/* IRQ Numbers for interrupts muxed through the FPGA */
+#define OMAP1510_INT_FPGA_ATN		(OMAP_FPGA_IRQ_BASE + 0)
+#define OMAP1510_INT_FPGA_ACK		(OMAP_FPGA_IRQ_BASE + 1)
+#define OMAP1510_INT_FPGA2		(OMAP_FPGA_IRQ_BASE + 2)
+#define OMAP1510_INT_FPGA3		(OMAP_FPGA_IRQ_BASE + 3)
+#define OMAP1510_INT_FPGA4		(OMAP_FPGA_IRQ_BASE + 4)
+#define OMAP1510_INT_FPGA5		(OMAP_FPGA_IRQ_BASE + 5)
+#define OMAP1510_INT_FPGA6		(OMAP_FPGA_IRQ_BASE + 6)
+#define OMAP1510_INT_FPGA7		(OMAP_FPGA_IRQ_BASE + 7)
+#define OMAP1510_INT_FPGA8		(OMAP_FPGA_IRQ_BASE + 8)
+#define OMAP1510_INT_FPGA9		(OMAP_FPGA_IRQ_BASE + 9)
+#define OMAP1510_INT_FPGA10		(OMAP_FPGA_IRQ_BASE + 10)
+#define OMAP1510_INT_FPGA11		(OMAP_FPGA_IRQ_BASE + 11)
+#define OMAP1510_INT_FPGA12		(OMAP_FPGA_IRQ_BASE + 12)
+#define OMAP1510_INT_ETHER		(OMAP_FPGA_IRQ_BASE + 13)
+#define OMAP1510_INT_FPGAUART1		(OMAP_FPGA_IRQ_BASE + 14)
+#define OMAP1510_INT_FPGAUART2		(OMAP_FPGA_IRQ_BASE + 15)
+#define OMAP1510_INT_FPGA_TS		(OMAP_FPGA_IRQ_BASE + 16)
+#define OMAP1510_INT_FPGA17		(OMAP_FPGA_IRQ_BASE + 17)
+#define OMAP1510_INT_FPGA_CAM		(OMAP_FPGA_IRQ_BASE + 18)
+#define OMAP1510_INT_FPGA_RTC_A		(OMAP_FPGA_IRQ_BASE + 19)
+#define OMAP1510_INT_FPGA_RTC_B		(OMAP_FPGA_IRQ_BASE + 20)
+#define OMAP1510_INT_FPGA_CD		(OMAP_FPGA_IRQ_BASE + 21)
+#define OMAP1510_INT_FPGA22		(OMAP_FPGA_IRQ_BASE + 22)
+#define OMAP1510_INT_FPGA23		(OMAP_FPGA_IRQ_BASE + 23)
+
 #endif /*  __ASM_ARCH_OMAP15XX_H */
 
diff --git a/arch/arm/mach-omap1/serial.c b/arch/arm/mach-omap1/serial.c
index b9d6834..d1ac080 100644
--- a/arch/arm/mach-omap1/serial.c
+++ b/arch/arm/mach-omap1/serial.c
@@ -23,7 +23,6 @@
 #include <asm/mach-types.h>
 
 #include <mach/mux.h>
-#include <plat/fpga.h>
 
 #include "pm.h"
 
diff --git a/arch/arm/plat-omap/debug-leds.c b/arch/arm/plat-omap/debug-leds.c
index ea29bbe..feca128 100644
--- a/arch/arm/plat-omap/debug-leds.c
+++ b/arch/arm/plat-omap/debug-leds.c
@@ -20,7 +20,7 @@
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
 
-#include <plat/fpga.h>
+#include "fpga.h"
 
 /* Many OMAP development platforms reuse the same "debug board"; these
  * platforms include H2, H3, H4, and Perseus2.  There are 16 LEDs on the
diff --git a/arch/arm/plat-omap/fpga.h b/arch/arm/plat-omap/fpga.h
new file mode 100644
index 0000000..54faaa9
--- /dev/null
+++ b/arch/arm/plat-omap/fpga.h
@@ -0,0 +1,74 @@
+/*
+ * arch/arm/plat-omap/include/mach/fpga.h
+ *
+ * Interrupt handler for OMAP-1510 FPGA
+ *
+ * Copyright (C) 2001 RidgeRun, Inc.
+ * Author: Greg Lonnon <glonnon@ridgerun.com>
+ *
+ * Copyright (C) 2002 MontaVista Software, Inc.
+ *
+ * Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
+ * Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_OMAP_FPGA_H
+#define __ASM_ARCH_OMAP_FPGA_H
+
+/*
+ * ---------------------------------------------------------------------------
+ *  H2/P2 Debug board FPGA
+ * ---------------------------------------------------------------------------
+ */
+/* maps in the FPGA registers and the ETHR registers */
+#define H2P2_DBG_FPGA_BASE		0xE8000000		/* VA */
+#define H2P2_DBG_FPGA_SIZE		SZ_4K			/* SIZE */
+#define H2P2_DBG_FPGA_START		0x04000000		/* PA */
+
+#define H2P2_DBG_FPGA_ETHR_START	(H2P2_DBG_FPGA_START + 0x300)
+#define H2P2_DBG_FPGA_FPGA_REV		IOMEM(H2P2_DBG_FPGA_BASE + 0x10)	/* FPGA Revision */
+#define H2P2_DBG_FPGA_BOARD_REV		IOMEM(H2P2_DBG_FPGA_BASE + 0x12)	/* Board Revision */
+#define H2P2_DBG_FPGA_GPIO		IOMEM(H2P2_DBG_FPGA_BASE + 0x14)	/* GPIO outputs */
+#define H2P2_DBG_FPGA_LEDS		IOMEM(H2P2_DBG_FPGA_BASE + 0x16)	/* LEDs outputs */
+#define H2P2_DBG_FPGA_MISC_INPUTS	IOMEM(H2P2_DBG_FPGA_BASE + 0x18)	/* Misc inputs */
+#define H2P2_DBG_FPGA_LAN_STATUS	IOMEM(H2P2_DBG_FPGA_BASE + 0x1A)	/* LAN Status line */
+#define H2P2_DBG_FPGA_LAN_RESET		IOMEM(H2P2_DBG_FPGA_BASE + 0x1C)	/* LAN Reset line */
+
+/* NOTE:  most boards don't have a static mapping for the FPGA ... */
+struct h2p2_dbg_fpga {
+	/* offset 0x00 */
+	u16		smc91x[8];
+	/* offset 0x10 */
+	u16		fpga_rev;
+	u16		board_rev;
+	u16		gpio_outputs;
+	u16		leds;
+	/* offset 0x18 */
+	u16		misc_inputs;
+	u16		lan_status;
+	u16		lan_reset;
+	u16		reserved0;
+	/* offset 0x20 */
+	u16		ps2_data;
+	u16		ps2_ctrl;
+	/* plus also 4 rs232 ports ... */
+};
+
+/* LEDs definition on debug board (16 LEDs, all physically green) */
+#define H2P2_DBG_FPGA_LED_GREEN		(1 << 15)
+#define H2P2_DBG_FPGA_LED_AMBER		(1 << 14)
+#define H2P2_DBG_FPGA_LED_RED		(1 << 13)
+#define H2P2_DBG_FPGA_LED_BLUE		(1 << 12)
+/*  cpu0 load-meter LEDs */
+#define H2P2_DBG_FPGA_LOAD_METER	(1 << 0)	// A bit of fun on our board ...
+#define H2P2_DBG_FPGA_LOAD_METER_SIZE	11
+#define H2P2_DBG_FPGA_LOAD_METER_MASK	((1 << H2P2_DBG_FPGA_LOAD_METER_SIZE) - 1)
+
+#define H2P2_DBG_FPGA_P2_LED_TIMER		(1 << 0)
+#define H2P2_DBG_FPGA_P2_LED_IDLE		(1 << 1)
+
+#endif
diff --git a/arch/arm/plat-omap/include/plat/fpga.h b/arch/arm/plat-omap/include/plat/fpga.h
deleted file mode 100644
index bd3c632..0000000
--- a/arch/arm/plat-omap/include/plat/fpga.h
+++ /dev/null
@@ -1,193 +0,0 @@
-/*
- * arch/arm/plat-omap/include/mach/fpga.h
- *
- * Interrupt handler for OMAP-1510 FPGA
- *
- * Copyright (C) 2001 RidgeRun, Inc.
- * Author: Greg Lonnon <glonnon@ridgerun.com>
- *
- * Copyright (C) 2002 MontaVista Software, Inc.
- *
- * Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
- * Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_OMAP_FPGA_H
-#define __ASM_ARCH_OMAP_FPGA_H
-
-extern void omap1510_fpga_init_irq(void);
-
-#define fpga_read(reg)			__raw_readb(reg)
-#define fpga_write(val, reg)		__raw_writeb(val, reg)
-
-/*
- * ---------------------------------------------------------------------------
- *  H2/P2 Debug board FPGA
- * ---------------------------------------------------------------------------
- */
-/* maps in the FPGA registers and the ETHR registers */
-#define H2P2_DBG_FPGA_BASE		0xE8000000		/* VA */
-#define H2P2_DBG_FPGA_SIZE		SZ_4K			/* SIZE */
-#define H2P2_DBG_FPGA_START		0x04000000		/* PA */
-
-#define H2P2_DBG_FPGA_ETHR_START	(H2P2_DBG_FPGA_START + 0x300)
-#define H2P2_DBG_FPGA_FPGA_REV		IOMEM(H2P2_DBG_FPGA_BASE + 0x10)	/* FPGA Revision */
-#define H2P2_DBG_FPGA_BOARD_REV		IOMEM(H2P2_DBG_FPGA_BASE + 0x12)	/* Board Revision */
-#define H2P2_DBG_FPGA_GPIO		IOMEM(H2P2_DBG_FPGA_BASE + 0x14)	/* GPIO outputs */
-#define H2P2_DBG_FPGA_LEDS		IOMEM(H2P2_DBG_FPGA_BASE + 0x16)	/* LEDs outputs */
-#define H2P2_DBG_FPGA_MISC_INPUTS	IOMEM(H2P2_DBG_FPGA_BASE + 0x18)	/* Misc inputs */
-#define H2P2_DBG_FPGA_LAN_STATUS	IOMEM(H2P2_DBG_FPGA_BASE + 0x1A)	/* LAN Status line */
-#define H2P2_DBG_FPGA_LAN_RESET		IOMEM(H2P2_DBG_FPGA_BASE + 0x1C)	/* LAN Reset line */
-
-/* NOTE:  most boards don't have a static mapping for the FPGA ... */
-struct h2p2_dbg_fpga {
-	/* offset 0x00 */
-	u16		smc91x[8];
-	/* offset 0x10 */
-	u16		fpga_rev;
-	u16		board_rev;
-	u16		gpio_outputs;
-	u16		leds;
-	/* offset 0x18 */
-	u16		misc_inputs;
-	u16		lan_status;
-	u16		lan_reset;
-	u16		reserved0;
-	/* offset 0x20 */
-	u16		ps2_data;
-	u16		ps2_ctrl;
-	/* plus also 4 rs232 ports ... */
-};
-
-/* LEDs definition on debug board (16 LEDs, all physically green) */
-#define H2P2_DBG_FPGA_LED_GREEN		(1 << 15)
-#define H2P2_DBG_FPGA_LED_AMBER		(1 << 14)
-#define H2P2_DBG_FPGA_LED_RED		(1 << 13)
-#define H2P2_DBG_FPGA_LED_BLUE		(1 << 12)
-/*  cpu0 load-meter LEDs */
-#define H2P2_DBG_FPGA_LOAD_METER	(1 << 0)	// A bit of fun on our board ...
-#define H2P2_DBG_FPGA_LOAD_METER_SIZE	11
-#define H2P2_DBG_FPGA_LOAD_METER_MASK	((1 << H2P2_DBG_FPGA_LOAD_METER_SIZE) - 1)
-
-#define H2P2_DBG_FPGA_P2_LED_TIMER		(1 << 0)
-#define H2P2_DBG_FPGA_P2_LED_IDLE		(1 << 1)
-
-/*
- * ---------------------------------------------------------------------------
- *  OMAP-1510 FPGA
- * ---------------------------------------------------------------------------
- */
-#define OMAP1510_FPGA_BASE		0xE8000000		/* VA */
-#define OMAP1510_FPGA_SIZE		SZ_4K
-#define OMAP1510_FPGA_START		0x08000000		/* PA */
-
-/* Revision */
-#define OMAP1510_FPGA_REV_LOW			IOMEM(OMAP1510_FPGA_BASE + 0x0)
-#define OMAP1510_FPGA_REV_HIGH			IOMEM(OMAP1510_FPGA_BASE + 0x1)
-
-#define OMAP1510_FPGA_LCD_PANEL_CONTROL		IOMEM(OMAP1510_FPGA_BASE + 0x2)
-#define OMAP1510_FPGA_LED_DIGIT			IOMEM(OMAP1510_FPGA_BASE + 0x3)
-#define INNOVATOR_FPGA_HID_SPI			IOMEM(OMAP1510_FPGA_BASE + 0x4)
-#define OMAP1510_FPGA_POWER			IOMEM(OMAP1510_FPGA_BASE + 0x5)
-
-/* Interrupt status */
-#define OMAP1510_FPGA_ISR_LO			IOMEM(OMAP1510_FPGA_BASE + 0x6)
-#define OMAP1510_FPGA_ISR_HI			IOMEM(OMAP1510_FPGA_BASE + 0x7)
-
-/* Interrupt mask */
-#define OMAP1510_FPGA_IMR_LO			IOMEM(OMAP1510_FPGA_BASE + 0x8)
-#define OMAP1510_FPGA_IMR_HI			IOMEM(OMAP1510_FPGA_BASE + 0x9)
-
-/* Reset registers */
-#define OMAP1510_FPGA_HOST_RESET		IOMEM(OMAP1510_FPGA_BASE + 0xa)
-#define OMAP1510_FPGA_RST			IOMEM(OMAP1510_FPGA_BASE + 0xb)
-
-#define OMAP1510_FPGA_AUDIO			IOMEM(OMAP1510_FPGA_BASE + 0xc)
-#define OMAP1510_FPGA_DIP			IOMEM(OMAP1510_FPGA_BASE + 0xe)
-#define OMAP1510_FPGA_FPGA_IO			IOMEM(OMAP1510_FPGA_BASE + 0xf)
-#define OMAP1510_FPGA_UART1			IOMEM(OMAP1510_FPGA_BASE + 0x14)
-#define OMAP1510_FPGA_UART2			IOMEM(OMAP1510_FPGA_BASE + 0x15)
-#define OMAP1510_FPGA_OMAP1510_STATUS		IOMEM(OMAP1510_FPGA_BASE + 0x16)
-#define OMAP1510_FPGA_BOARD_REV			IOMEM(OMAP1510_FPGA_BASE + 0x18)
-#define OMAP1510P1_PPT_DATA			IOMEM(OMAP1510_FPGA_BASE + 0x100)
-#define OMAP1510P1_PPT_STATUS			IOMEM(OMAP1510_FPGA_BASE + 0x101)
-#define OMAP1510P1_PPT_CONTROL			IOMEM(OMAP1510_FPGA_BASE + 0x102)
-
-#define OMAP1510_FPGA_TOUCHSCREEN		IOMEM(OMAP1510_FPGA_BASE + 0x204)
-
-#define INNOVATOR_FPGA_INFO			IOMEM(OMAP1510_FPGA_BASE + 0x205)
-#define INNOVATOR_FPGA_LCD_BRIGHT_LO		IOMEM(OMAP1510_FPGA_BASE + 0x206)
-#define INNOVATOR_FPGA_LCD_BRIGHT_HI		IOMEM(OMAP1510_FPGA_BASE + 0x207)
-#define INNOVATOR_FPGA_LED_GRN_LO		IOMEM(OMAP1510_FPGA_BASE + 0x208)
-#define INNOVATOR_FPGA_LED_GRN_HI		IOMEM(OMAP1510_FPGA_BASE + 0x209)
-#define INNOVATOR_FPGA_LED_RED_LO		IOMEM(OMAP1510_FPGA_BASE + 0x20a)
-#define INNOVATOR_FPGA_LED_RED_HI		IOMEM(OMAP1510_FPGA_BASE + 0x20b)
-#define INNOVATOR_FPGA_CAM_USB_CONTROL		IOMEM(OMAP1510_FPGA_BASE + 0x20c)
-#define INNOVATOR_FPGA_EXP_CONTROL		IOMEM(OMAP1510_FPGA_BASE + 0x20d)
-#define INNOVATOR_FPGA_ISR2			IOMEM(OMAP1510_FPGA_BASE + 0x20e)
-#define INNOVATOR_FPGA_IMR2			IOMEM(OMAP1510_FPGA_BASE + 0x210)
-
-#define OMAP1510_FPGA_ETHR_START		(OMAP1510_FPGA_START + 0x300)
-
-/*
- * Power up Giga UART driver, turn on HID clock.
- * Turn off BT power, since we're not using it and it
- * draws power.
- */
-#define OMAP1510_FPGA_RESET_VALUE		0x42
-
-#define OMAP1510_FPGA_PCR_IF_PD0		(1 << 7)
-#define OMAP1510_FPGA_PCR_COM2_EN		(1 << 6)
-#define OMAP1510_FPGA_PCR_COM1_EN		(1 << 5)
-#define OMAP1510_FPGA_PCR_EXP_PD0		(1 << 4)
-#define OMAP1510_FPGA_PCR_EXP_PD1		(1 << 3)
-#define OMAP1510_FPGA_PCR_48MHZ_CLK		(1 << 2)
-#define OMAP1510_FPGA_PCR_4MHZ_CLK		(1 << 1)
-#define OMAP1510_FPGA_PCR_RSRVD_BIT0		(1 << 0)
-
-/*
- * Innovator/OMAP1510 FPGA HID register bit definitions
- */
-#define OMAP1510_FPGA_HID_SCLK	(1<<0)	/* output */
-#define OMAP1510_FPGA_HID_MOSI	(1<<1)	/* output */
-#define OMAP1510_FPGA_HID_nSS	(1<<2)	/* output 0/1 chip idle/select */
-#define OMAP1510_FPGA_HID_nHSUS	(1<<3)	/* output 0/1 host active/suspended */
-#define OMAP1510_FPGA_HID_MISO	(1<<4)	/* input */
-#define OMAP1510_FPGA_HID_ATN	(1<<5)	/* input  0/1 chip idle/ATN */
-#define OMAP1510_FPGA_HID_rsrvd	(1<<6)
-#define OMAP1510_FPGA_HID_RESETn (1<<7)	/* output - 0/1 USAR reset/run */
-
-/* The FPGA IRQ is cascaded through GPIO_13 */
-#define OMAP1510_INT_FPGA		(IH_GPIO_BASE + 13)
-
-/* IRQ Numbers for interrupts muxed through the FPGA */
-#define OMAP1510_INT_FPGA_ATN		(OMAP_FPGA_IRQ_BASE + 0)
-#define OMAP1510_INT_FPGA_ACK		(OMAP_FPGA_IRQ_BASE + 1)
-#define OMAP1510_INT_FPGA2		(OMAP_FPGA_IRQ_BASE + 2)
-#define OMAP1510_INT_FPGA3		(OMAP_FPGA_IRQ_BASE + 3)
-#define OMAP1510_INT_FPGA4		(OMAP_FPGA_IRQ_BASE + 4)
-#define OMAP1510_INT_FPGA5		(OMAP_FPGA_IRQ_BASE + 5)
-#define OMAP1510_INT_FPGA6		(OMAP_FPGA_IRQ_BASE + 6)
-#define OMAP1510_INT_FPGA7		(OMAP_FPGA_IRQ_BASE + 7)
-#define OMAP1510_INT_FPGA8		(OMAP_FPGA_IRQ_BASE + 8)
-#define OMAP1510_INT_FPGA9		(OMAP_FPGA_IRQ_BASE + 9)
-#define OMAP1510_INT_FPGA10		(OMAP_FPGA_IRQ_BASE + 10)
-#define OMAP1510_INT_FPGA11		(OMAP_FPGA_IRQ_BASE + 11)
-#define OMAP1510_INT_FPGA12		(OMAP_FPGA_IRQ_BASE + 12)
-#define OMAP1510_INT_ETHER		(OMAP_FPGA_IRQ_BASE + 13)
-#define OMAP1510_INT_FPGAUART1		(OMAP_FPGA_IRQ_BASE + 14)
-#define OMAP1510_INT_FPGAUART2		(OMAP_FPGA_IRQ_BASE + 15)
-#define OMAP1510_INT_FPGA_TS		(OMAP_FPGA_IRQ_BASE + 16)
-#define OMAP1510_INT_FPGA17		(OMAP_FPGA_IRQ_BASE + 17)
-#define OMAP1510_INT_FPGA_CAM		(OMAP_FPGA_IRQ_BASE + 18)
-#define OMAP1510_INT_FPGA_RTC_A		(OMAP_FPGA_IRQ_BASE + 19)
-#define OMAP1510_INT_FPGA_RTC_B		(OMAP_FPGA_IRQ_BASE + 20)
-#define OMAP1510_INT_FPGA_CD		(OMAP_FPGA_IRQ_BASE + 21)
-#define OMAP1510_INT_FPGA22		(OMAP_FPGA_IRQ_BASE + 22)
-#define OMAP1510_INT_FPGA23		(OMAP_FPGA_IRQ_BASE + 23)
-
-#endif
diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c
index 4531d03..439e6e4 100644
--- a/drivers/usb/host/ohci-omap.c
+++ b/drivers/usb/host/ohci-omap.c
@@ -25,7 +25,6 @@
 #include <asm/mach-types.h>
 
 #include <mach/mux.h>
-#include <plat/fpga.h>
 
 #include <mach/hardware.h>
 #include <mach/irqs.h>
@@ -93,14 +92,14 @@ static int omap_ohci_transceiver_power(int on)
 {
 	if (on) {
 		if (machine_is_omap_innovator() && cpu_is_omap1510())
-			fpga_write(fpga_read(INNOVATOR_FPGA_CAM_USB_CONTROL)
+			__raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
 				| ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
 			       INNOVATOR_FPGA_CAM_USB_CONTROL);
 		else if (machine_is_omap_osk())
 			tps65010_set_gpio_out_value(GPIO1, LOW);
 	} else {
 		if (machine_is_omap_innovator() && cpu_is_omap1510())
-			fpga_write(fpga_read(INNOVATOR_FPGA_CAM_USB_CONTROL)
+			__raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
 				& ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
 			       INNOVATOR_FPGA_CAM_USB_CONTROL);
 		else if (machine_is_omap_osk())
diff --git a/drivers/video/omap/lcd_inn1510.c b/drivers/video/omap/lcd_inn1510.c
index b38b1dd..2ee4232 100644
--- a/drivers/video/omap/lcd_inn1510.c
+++ b/drivers/video/omap/lcd_inn1510.c
@@ -23,7 +23,8 @@
 #include <linux/platform_device.h>
 #include <linux/io.h>
 
-#include <plat/fpga.h>
+#include <mach/hardware.h>
+
 #include "omapfb.h"
 
 static int innovator1510_panel_init(struct lcd_panel *panel,
@@ -38,13 +39,13 @@ static void innovator1510_panel_cleanup(struct lcd_panel *panel)
 
 static int innovator1510_panel_enable(struct lcd_panel *panel)
 {
-	fpga_write(0x7, OMAP1510_FPGA_LCD_PANEL_CONTROL);
+	__raw_writeb(0x7, OMAP1510_FPGA_LCD_PANEL_CONTROL);
 	return 0;
 }
 
 static void innovator1510_panel_disable(struct lcd_panel *panel)
 {
-	fpga_write(0x0, OMAP1510_FPGA_LCD_PANEL_CONTROL);
+	__raw_writeb(0x0, OMAP1510_FPGA_LCD_PANEL_CONTROL);
 }
 
 static unsigned long innovator1510_panel_get_caps(struct lcd_panel *panel)
