| Message ID | 20140707214340.GA29061@amd.pavel.ucw.cz (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi! Pavel Machek <pavel@denx.de> writes: > Hi! > >> > I made this, but ethernet problems I currently see are not frequent >> > enough to allow easy debugging. If link takes long to estabilish for >> > you, could you test the patch below? > >> > +static int ksz9021rn_phy_fixup(struct phy_device *phydev) >> > +{ >> > + if (IS_BUILTIN(CONFIG_PHYLIB)) { >> > + printk("------------- running phy fixup\n"); >> > + >> > + /* min rx data delay */ >> > + phy_write(phydev, MICREL_KSZ9021_EXTREG_CTRL, >> > + 0x8000 | MICREL_KSZ9021_RGMII_RX_DATA_PAD_SKEW); >> > + phy_write(phydev, MICREL_KSZ9021_EXTREG_DATA_WRITE, 0x0000); >> > + >> > + phy_write(phydev, MICREL_KSZ9021_EXTREG_CTRL, >> > + 0x8000 | MICREL_KSZ9021_RGMII_TX_DATA_PAD_SKEW); >> > + phy_write(phydev, MICREL_KSZ9021_EXTREG_DATA_WRITE, 0x0000); >> > + >> > + /* max rx/tx clock delay, min rx/tx control delay */ >> > + phy_write(phydev, MICREL_KSZ9021_EXTREG_CTRL, >> > + 0x8000 | MICREL_KSZ9021_RGMII_CLK_CTRL_PAD_SKEW); >> > + phy_write(phydev, MICREL_KSZ9021_EXTREG_DATA_WRITE, 0xf0f0); >> > + phy_write(phydev, MICREL_KSZ9021_EXTREG_CTRL, >> > + MICREL_KSZ9021_RGMII_CLK_CTRL_PAD_SKEW); >> > + } >> > + >> > + return 0; >> > +} >> > + >> >> All of this stuff is not needed as it's already taken care of by the >> Micrel phy driver. The clock skew values are now represented in the DTS. >> Please look at: >> >> Documentation/devicetree/bindings/net/micrel-ksz90x1.txt > > Aah, thanks for the pointer. > > At least socfpga_cyclone5_socrates.dts is in the mainline, but it does > not have any skew configuration. That may explain why the board seems > to have problems with ethernet... (or not). > The socrates does not have these values, because it does not have a Micrel PHY... > Are there suitable default values? > > u-boot uses these defaults: > > include/configs/socfpga_common.h:#define CONFIG_KSZ9021_CLK_SKEW_VAL > 0xf0f0 > include/configs/socfpga_common.h:#define CONFIG_KSZ9021_DATA_SKEW_VAL > 0x0 > > ...that should correspond to txc-skew-ps == rxc-skew-ps == 3000, all > other skew values == 0? > > Could someone with socrates board and network problems test if this > makes any difference? > ...so, would this even apply to the socrates then? Regards, Steffen
Hi! On 07.07.2014 23:43, Pavel Machek wrote: >> All of this stuff is not needed as it's already taken care of by the >> Micrel phy driver. The clock skew values are now represented in the DTS. >> Please look at: >> >> Documentation/devicetree/bindings/net/micrel-ksz90x1.txt > > Aah, thanks for the pointer. > > At least socfpga_cyclone5_socrates.dts is in the mainline, but it does > not have any skew configuration. That may explain why the board seems > to have problems with ethernet... (or not). > > Are there suitable default values? > > u-boot uses these defaults: > > include/configs/socfpga_common.h:#define CONFIG_KSZ9021_CLK_SKEW_VAL > 0xf0f0 > include/configs/socfpga_common.h:#define CONFIG_KSZ9021_DATA_SKEW_VAL > 0x0 > > ...that should correspond to txc-skew-ps == rxc-skew-ps == 3000, all > other skew values == 0? > > Could someone with socrates board and network problems test if this > makes any difference? SoCrates uses a different PHY, the Lantiq PEF7071 (PHY11G). So those dts additions have no effect on SoCrates. Thanks, Stefan
Hi! > >Are there suitable default values? > > > >u-boot uses these defaults: > > > >include/configs/socfpga_common.h:#define CONFIG_KSZ9021_CLK_SKEW_VAL > >0xf0f0 > >include/configs/socfpga_common.h:#define CONFIG_KSZ9021_DATA_SKEW_VAL > >0x0 > > > >...that should correspond to txc-skew-ps == rxc-skew-ps == 3000, all > >other skew values == 0? > > > >Could someone with socrates board and network problems test if this > >makes any difference? > > SoCrates uses a different PHY, the Lantiq PEF7071 (PHY11G). So those > dts additions have no effect on SoCrates. Oops, I guess I was confused. Pavel
Hi! > >> All of this stuff is not needed as it's already taken care of by the > >> Micrel phy driver. The clock skew values are now represented in the DTS. > >> Please look at: > >> > >> Documentation/devicetree/bindings/net/micrel-ksz90x1.txt > > > > Aah, thanks for the pointer. > > > > At least socfpga_cyclone5_socrates.dts is in the mainline, but it does > > not have any skew configuration. That may explain why the board seems > > to have problems with ethernet... (or not). > > The socrates does not have these values, because it does not have a > Micrel PHY... Hmm, that is not it, then :-(. Is there any other setup that needs to be done? Because from the experience with the socrates boards, they are quite picky about cabling used. Thanks and best regards, Pavel
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts b/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts index a1814b4..eba8eea 100644 --- a/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts +++ b/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts @@ -34,6 +34,16 @@ &gmac1 { status = "okay"; + phy-mode = "rgmii"; + + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txen-skew-ps = <0>; + txc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <3000>; }; &i2c0 {