| Message ID | 20170120132650.9784-3-martin.blumenstingl@googlemail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 01/20/2017 02:26 PM, Martin Blumenstingl wrote: > This resets the ethernet PHY during boot to get the PHY into a "clean" > state. > While here also specify the phy-handle of the ethmac node to make the > PHY configuration similar to the one we have on GXL devices. This will > allow us to specify OF-properties for the PHY itself. > > Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> > --- > arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts | 24 ++++++++++++++++++++++++ > 1 file changed, 24 insertions(+) > > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts > index 39bb037a3e47..5d2cd2ecfdc4 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts > +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts > @@ -50,3 +50,27 @@ > compatible = "amlogic,p201", "amlogic,meson-gxbb"; > model = "Amlogic Meson GXBB P201 Development Board"; > }; > + > +ðmac { > + status = "okay"; > + pinctrl-0 = <ð_rgmii_pins>; > + pinctrl-names = "default"; > + phy-handle = <ð_phy0>; > + phy-mode = "rgmii"; > + > + snps,reset-gpio = <&gpio GPIOZ_14 0>; > + snps,reset-delays-us = <0 10000 1000000>; > + snps,reset-active-low; > + > + mdio { > + compatible = "snps,dwmac-mdio"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + eth_phy0: ethernet-phy@0 { > + compatible = "ethernet-phy-id0022.1620", > + "ethernet-phy-ieee802.3-c22"; > + reg = <3>; > + }; > + }; > +}; > Hi Martin, It seems you mismatched the p200 and the p201, it's the p201 nobody has and uses a rmii link. Neil
On Fri, Jan 20, 2017 at 2:31 PM, Neil Armstrong <narmstrong@baylibre.com> wrote: > On 01/20/2017 02:26 PM, Martin Blumenstingl wrote: >> This resets the ethernet PHY during boot to get the PHY into a "clean" >> state. >> While here also specify the phy-handle of the ethmac node to make the >> PHY configuration similar to the one we have on GXL devices. This will >> allow us to specify OF-properties for the PHY itself. >> >> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> >> --- >> arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts | 24 ++++++++++++++++++++++++ >> 1 file changed, 24 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts >> index 39bb037a3e47..5d2cd2ecfdc4 100644 >> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts >> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts >> @@ -50,3 +50,27 @@ >> compatible = "amlogic,p201", "amlogic,meson-gxbb"; >> model = "Amlogic Meson GXBB P201 Development Board"; >> }; >> + >> +ðmac { >> + status = "okay"; >> + pinctrl-0 = <ð_rgmii_pins>; >> + pinctrl-names = "default"; >> + phy-handle = <ð_phy0>; >> + phy-mode = "rgmii"; >> + >> + snps,reset-gpio = <&gpio GPIOZ_14 0>; >> + snps,reset-delays-us = <0 10000 1000000>; >> + snps,reset-active-low; >> + >> + mdio { >> + compatible = "snps,dwmac-mdio"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + eth_phy0: ethernet-phy@0 { >> + compatible = "ethernet-phy-id0022.1620", >> + "ethernet-phy-ieee802.3-c22"; >> + reg = <3>; >> + }; >> + }; >> +}; >> > > Hi Martin, > > It seems you mismatched the p200 and the p201, it's the p201 nobody has and uses a rmii link. ouch, good catch. I'll send a fix for that later - thanks for spotting!
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts index 39bb037a3e47..5d2cd2ecfdc4 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts @@ -50,3 +50,27 @@ compatible = "amlogic,p201", "amlogic,meson-gxbb"; model = "Amlogic Meson GXBB P201 Development Board"; }; + +ðmac { + status = "okay"; + pinctrl-0 = <ð_rgmii_pins>; + pinctrl-names = "default"; + phy-handle = <ð_phy0>; + phy-mode = "rgmii"; + + snps,reset-gpio = <&gpio GPIOZ_14 0>; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-active-low; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + eth_phy0: ethernet-phy@0 { + compatible = "ethernet-phy-id0022.1620", + "ethernet-phy-ieee802.3-c22"; + reg = <3>; + }; + }; +};
This resets the ethernet PHY during boot to get the PHY into a "clean" state. While here also specify the phy-handle of the ethmac node to make the PHY configuration similar to the one we have on GXL devices. This will allow us to specify OF-properties for the PHY itself. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> --- arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+)