diff mbox

[v2,11/18] arm64: dts: meson-gxbb-odroidc2: Fix node order

Message ID 20170513143337.14278-12-afaerber@suse.de (mailing list archive)
State New, archived
Headers show

Commit Message

Andreas Färber May 13, 2017, 2:33 p.m. UTC 
Sort nodes referenced by label alphabetically.

Signed-off-by: Andreas Färber <afaerber@suse.de>
---
 v1 -> v2:
 * Rebased (new nodes added)
 
 .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 108 ++++++++++-----------
 1 file changed, 54 insertions(+), 54 deletions(-)

Comments

Neil Armstrong May 15, 2017, 8:17 a.m. UTC | #1 
On 05/13/2017 04:33 PM, Andreas Färber wrote:
> Sort nodes referenced by label alphabetically.
> 
> Signed-off-by: Andreas Färber <afaerber@suse.de>
> ---
>  v1 -> v2:
>  * Rebased (new nodes added)
>  
>  .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 108 ++++++++++-----------
>  1 file changed, 54 insertions(+), 54 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> index 54a9c6a6b392..d147c853ab05 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> @@ -137,16 +137,6 @@
>  	};
>  };
>  
> -&scpi_clocks {
> -	status = "disabled";
> -};
> -
> -&uart_AO {
> -	status = "okay";
> -	pinctrl-0 = <&uart_ao_a_pins>;
> -	pinctrl-names = "default";
> -};
> -
>  &ethmac {
>  	status = "okay";
>  	pinctrl-0 = <&eth_rgmii_pins>;
> @@ -172,6 +162,33 @@
>  	};
>  };
>  
> +&gpio_ao {
> +	/*
> +	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
> +	 * to be turned high in order to be detected by the USB Controller
> +	 * This signal should be handled by a USB specific power sequence
> +	 * in order to reset the Hub when USB bus is powered down.
> +	 */
> +	usb-hub {
> +		gpio-hog;
> +		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "usb-hub-reset";
> +	};
> +};
> +
> +&i2c_A {
> +	status = "okay";
> +	pinctrl-0 = <&i2c_a_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&ir {
> +	status = "okay";
> +	pinctrl-0 = <&remote_input_ao_pins>;
> +	pinctrl-names = "default";
> +};
> +
>  &pinctrl_aobus {
>  	gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
>  			  "USB HUB nRESET", "USB OTG Power En",
> @@ -223,55 +240,15 @@
>  			  "";
>  };
>  
> -&ir {
> -	status = "okay";
> -	pinctrl-0 = <&remote_input_ao_pins>;
> -	pinctrl-names = "default";
> -};
> -
> -&i2c_A {
> -	status = "okay";
> -	pinctrl-0 = <&i2c_a_pins>;
> -	pinctrl-names = "default";
> -};
> -
> -&gpio_ao {
> -	/*
> -	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
> -	 * to be turned high in order to be detected by the USB Controller
> -	 * This signal should be handled by a USB specific power sequence
> -	 * in order to reset the Hub when USB bus is powered down.
> -	 */
> -	usb-hub {
> -		gpio-hog;
> -		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
> -		output-high;
> -		line-name = "usb-hub-reset";
> -	};
> -};
> -
> -&usb0_phy {
> -	status = "okay";
> -	phy-supply = <&usb_otg_pwr>;
> -};
> -
> -&usb1_phy {
> -	status = "okay";
> -};
> -
> -&usb0 {
> -	status = "okay";
> -};
> -
> -&usb1 {
> -	status = "okay";
> -};
> -
>  &saradc {
>  	status = "okay";
>  	vref-supply = <&vcc1v8>;
>  };
>  
> +&scpi_clocks {
> +	status = "disabled";
> +};
> +
>  /* SD */
>  &sd_emmc_b {
>  	status = "okay";
> @@ -309,3 +286,26 @@
>  	vmmc-supply = <&vcc3v3>;
>  	vqmmc-supply = <&vcc1v8>;
>  };
> +
> +&uart_AO {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_a_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&usb0_phy {
> +	status = "okay";
> +	phy-supply = <&usb_otg_pwr>;
> +};
> +
> +&usb1_phy {
> +	status = "okay";
> +};
> +
> +&usb0 {
> +	status = "okay";
> +};
> +
> +&usb1 {
> +	status = "okay";
> +};
> 

Hi Andreas,

Like a previous attempt, I'm not OK with such rework since it will break bisect and add complexity for new patches handling.

The order is not alphabetically ordered, live with it.

Neil
diff mbox

Patch

diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index 54a9c6a6b392..d147c853ab05 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -137,16 +137,6 @@ 
 	};
 };
 
-&scpi_clocks {
-	status = "disabled";
-};
-
-&uart_AO {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_a_pins>;
-	pinctrl-names = "default";
-};
-
 &ethmac {
 	status = "okay";
 	pinctrl-0 = <&eth_rgmii_pins>;
@@ -172,6 +162,33 @@ 
 	};
 };
 
+&gpio_ao {
+	/*
+	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
+	 * to be turned high in order to be detected by the USB Controller
+	 * This signal should be handled by a USB specific power sequence
+	 * in order to reset the Hub when USB bus is powered down.
+	 */
+	usb-hub {
+		gpio-hog;
+		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&i2c_A {
+	status = "okay";
+	pinctrl-0 = <&i2c_a_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
 &pinctrl_aobus {
 	gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
 			  "USB HUB nRESET", "USB OTG Power En",
@@ -223,55 +240,15 @@ 
 			  "";
 };
 
-&ir {
-	status = "okay";
-	pinctrl-0 = <&remote_input_ao_pins>;
-	pinctrl-names = "default";
-};
-
-&i2c_A {
-	status = "okay";
-	pinctrl-0 = <&i2c_a_pins>;
-	pinctrl-names = "default";
-};
-
-&gpio_ao {
-	/*
-	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
-};
-
-&usb0_phy {
-	status = "okay";
-	phy-supply = <&usb_otg_pwr>;
-};
-
-&usb1_phy {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-};
-
-&usb1 {
-	status = "okay";
-};
-
 &saradc {
 	status = "okay";
 	vref-supply = <&vcc1v8>;
 };
 
+&scpi_clocks {
+	status = "disabled";
+};
+
 /* SD */
 &sd_emmc_b {
 	status = "okay";
@@ -309,3 +286,26 @@ 
 	vmmc-supply = <&vcc3v3>;
 	vqmmc-supply = <&vcc1v8>;
 };
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0_phy {
+	status = "okay";
+	phy-supply = <&usb_otg_pwr>;
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};