@@ -17,7 +17,6 @@ config OMAP_REMOTEPROC
depends on HAS_DMA
depends on ARCH_OMAP4 || SOC_OMAP5
depends on OMAP_IOMMU
- depends on REMOTEPROC
select MAILBOX
select OMAP2PLUS_MBOX
select RPMSG_VIRTIO
@@ -37,7 +36,6 @@ config OMAP_REMOTEPROC
config WKUP_M3_RPROC
tristate "AMx3xx Wakeup M3 remoteproc support"
depends on SOC_AM33XX || SOC_AM43XX
- depends on REMOTEPROC
help
Say y here to support Wakeup M3 remote processor on TI AM33xx
and AM43xx family of SoCs.
@@ -50,7 +48,6 @@ config WKUP_M3_RPROC
config DA8XX_REMOTEPROC
tristate "DA8xx/OMAP-L13x remoteproc support"
depends on ARCH_DAVINCI_DA8XX
- depends on REMOTEPROC
depends on DMA_CMA
select RPMSG_VIRTIO
help
@@ -74,7 +71,6 @@ config KEYSTONE_REMOTEPROC
tristate "Keystone Remoteproc support"
depends on ARCH_KEYSTONE
depends on RESET_CONTROLLER
- depends on REMOTEPROC
select RPMSG_VIRTIO
help
Say Y here here to support Keystone remote processors (DSP)
@@ -86,7 +82,6 @@ config KEYSTONE_REMOTEPROC
config QCOM_ADSP_PIL
tristate "Qualcomm ADSP Peripheral Image Loader"
depends on OF && ARCH_QCOM
- depends on REMOTEPROC
depends on QCOM_SMEM
depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
select MFD_SYSCON
@@ -104,7 +99,6 @@ config QCOM_Q6V5_PIL
tristate "Qualcomm Hexagon V5 Peripherial Image Loader"
depends on OF && ARCH_QCOM
depends on QCOM_SMEM
- depends on REMOTEPROC
depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
select MFD_SYSCON
select QCOM_RPROC_COMMON
@@ -118,7 +112,6 @@ config QCOM_WCNSS_PIL
depends on OF && ARCH_QCOM
depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
depends on QCOM_SMEM
- depends on REMOTEPROC
select QCOM_MDT_LOADER
select QCOM_RPROC_COMMON
select QCOM_SCM
@@ -129,7 +122,6 @@ config QCOM_WCNSS_PIL
config ST_REMOTEPROC
tristate "ST remoteproc support"
depends on ARCH_STI
- depends on REMOTEPROC
select MAILBOX
select STI_MBOX
select RPMSG_VIRTIO
@@ -140,7 +132,6 @@ config ST_REMOTEPROC
config ST_SLIM_REMOTEPROC
tristate
- depends on REMOTEPROC
endif # REMOTEPROC
All the remoteproc platform driver Kconfig symbols are defined and included under an if REMOTEPROC condition, so the dependency on REMOTEPROC is implicit and they do not need an explicit 'depends on REMOTEPROC' line. So, clean these up. Signed-off-by: Suman Anna <s-anna@ti.com> --- drivers/remoteproc/Kconfig | 9 --------- 1 file changed, 9 deletions(-)