@@ -4,7 +4,9 @@ This driver follows the usual GPIO bindings found in
Documentation/devicetree/bindings/gpio/gpio.txt
Required properties:
-- compatible: Should be "x-powers,axp209-gpio"
+- compatible: Should be one of:
+ - "x-powers,axp209-gpio"
+ - "x-powers,axp813-gpio"
- #gpio-cells: Should be two. The first cell is the pin number and the
second is the GPIO flags.
- gpio-controller: Marks the device node as a GPIO controller.
@@ -49,8 +51,17 @@ Example:
GPIOs and their functions
-------------------------
+axp209
+------
GPIO | Functions
------------------------
GPIO0 | gpio_in, gpio_out, ldo, adc
GPIO1 | gpio_in, gpio_out, ldo, adc
GPIO2 | gpio_in, gpio_out
+
+axp813
+------
+GPIO | Functions
+------------------------
+GPIO0 | gpio_in, gpio_out, ldo, adc
+GPIO1 | gpio_in, gpio_out, ldo
@@ -19,6 +19,7 @@
#include <linux/mfd/axp20x.h>
#include <linux/module.h>
#include <linux/of.h>
+#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
#include <linux/slab.h>
@@ -70,6 +71,11 @@ static const struct pinctrl_pin_desc axp209_pins[] = {
PINCTRL_PIN(2, "GPIO2"),
};
+static const struct pinctrl_pin_desc axp813_pins[] = {
+ PINCTRL_PIN(0, "GPIO0"),
+ PINCTRL_PIN(1, "GPIO1"),
+};
+
static const struct axp20x_pctrl_desc axp20x_data = {
.pins = axp209_pins,
.npins = ARRAY_SIZE(axp209_pins),
@@ -78,6 +84,14 @@ static const struct axp20x_pctrl_desc axp20x_data = {
.gpio_status_offset = 4,
};
+static const struct axp20x_pctrl_desc axp813_data = {
+ .pins = axp813_pins,
+ .npins = ARRAY_SIZE(axp813_pins),
+ .ldo_mask = BIT(0) | BIT(1),
+ .adc_mask = BIT(0),
+ .gpio_status_offset = 0,
+};
+
static int axp20x_gpio_get_reg(unsigned offset)
{
switch (offset) {
@@ -341,10 +355,18 @@ static void axp20x_build_funcs_groups(struct platform_device *pdev)
pctl->desc->pins);
}
+static const struct of_device_id axp20x_pctl_match[] = {
+ { .compatible = "x-powers,axp209-gpio", .data = &axp20x_data, },
+ { .compatible = "x-powers,axp813-gpio", .data = &axp813_data, },
+ { }
+};
+MODULE_DEVICE_TABLE(of, axp20x_pctl_match);
+
static int axp20x_pctl_probe(struct platform_device *pdev)
{
struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
struct axp20x_pctl *pctl;
+ struct device *dev = &pdev->dev;
struct pinctrl_desc *pctrl_desc;
int ret;
@@ -372,9 +394,9 @@ static int axp20x_pctl_probe(struct platform_device *pdev)
pctl->chip.set = axp20x_gpio_set;
pctl->chip.direction_input = axp20x_gpio_input;
pctl->chip.direction_output = axp20x_gpio_output;
- pctl->chip.ngpio = 3;
+ pctl->chip.ngpio = pctl->desc->npins;
- pctl->desc = &axp20x_data;
+ pctl->desc = (struct axp20x_pctrl_desc *)of_device_get_match_data(dev);
pctl->regmap = axp20x->regmap;
@@ -421,12 +443,6 @@ static int axp20x_pctl_probe(struct platform_device *pdev)
return 0;
}
-static const struct of_device_id axp20x_pctl_match[] = {
- { .compatible = "x-powers,axp209-gpio" },
- { }
-};
-MODULE_DEVICE_TABLE(of, axp20x_pctl_match);
-
static struct platform_driver axp20x_pctl_driver = {
.probe = axp20x_pctl_probe,
.driver = {
The AXP813 has only two GPIOs. GPIO0 can either be used as a GPIO, an LDO regulator or an ADC. GPIO1 can be used either as a GPIO or an LDO regulator. Moreover, the status bit of the GPIOs when in input mode is not offset by 4 unlike the AXP209. Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com> --- .../devicetree/bindings/pinctrl/pinctrl-axp209.txt | 13 ++++++++- drivers/pinctrl/pinctrl-axp209.c | 32 ++++++++++++++++------ 2 files changed, 36 insertions(+), 9 deletions(-)