@@ -56,7 +56,7 @@
};
/* 24 MHz chrystal on the Integrator/AP development board */
- xtal24mhz: xtal24mhz@24M {
+ xtal24mhz: xtal24mhz@24m {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
@@ -71,7 +71,7 @@
};
/* The UART clock is 14.74 MHz divided by an ICS525 */
- uartclk: uartclk@14.74M {
+ uartclk: uartclk@14.74m {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <14745600>;
@@ -80,14 +80,14 @@
core-module@10000000 {
/* 24 MHz chrystal on the core module */
- cm24mhz: cm24mhz@24M {
+ cm24mhz: cm24mhz@24m {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
};
/* Oscillator on the core module, clocks the CPU core */
- cmosc: cmosc@24M {
+ cmosc: cmosc@24m {
compatible = "arm,syscon-icst525-integratorap-cm";
#clock-cells = <0>;
lock-offset = <0x14>;
@@ -96,7 +96,7 @@
};
/* Auxilary oscillator on the core module, 32.369MHz at boot */
- auxosc: auxosc@24M {
+ auxosc: auxosc@24m {
compatible = "arm,syscon-icst525";
#clock-cells = <0>;
lock-offset = <0x14>;
@@ -116,7 +116,7 @@
* SYSCLK clocks PCIv3 bridge, system controller and the
* logic modules.
*/
- sysclk: apsys@24M {
+ sysclk: apsys@24m {
compatible = "arm,syscon-icst525-integratorap-sys";
#clock-cells = <0>;
lock-offset = <0x1c>;
@@ -125,7 +125,7 @@
};
/* One-bit control for the PCI bus clock (33 or 25 MHz) */
- pciclk: pciclk@24M {
+ pciclk: pciclk@24m {
compatible = "arm,syscon-icst525-integratorap-pci";
#clock-cells = <0>;
lock-offset = <0x1c>;
@@ -47,14 +47,14 @@
*/
/* The codec chrystal operates at 24.576 MHz */
- xtal_codec: xtal24.576@24.576M {
+ xtal_codec: xtal24.576@24.576m {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24576000>;
};
/* The chrystal is divided by 2 by the codec for the AACI bit clock */
- aaci_bitclk: aaci_bitclk@12.288M {
+ aaci_bitclk: aaci_bitclk@12.288m {
#clock-cells = <0>;
compatible = "fixed-factor-clock";
clock-div = <2>;
@@ -63,14 +63,14 @@
};
/* This is a 25MHz chrystal on the base board */
- xtal25mhz: xtal25mhz@25M {
+ xtal25mhz: xtal25mhz@25m {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <25000000>;
};
/* The UART clock is 14.74 MHz divided from 25MHz by an ICS525 */
- uartclk: uartclk@14.74M {
+ uartclk: uartclk@14.74m {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <14745600>;
@@ -85,14 +85,14 @@
core-module@10000000 {
/* 24 MHz chrystal on the core module */
- cm24mhz: cm24mhz@24M {
+ cm24mhz: cm24mhz@24m {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
};
/* Oscillator on the core module, clocks the CPU core */
- cmcore: cmosc@24M {
+ cmcore: cmosc@24m {
compatible = "arm,syscon-icst525-integratorcp-cm-core";
#clock-cells = <0>;
lock-offset = <0x14>;
@@ -101,7 +101,7 @@
};
/* Oscillator on the core module, clocks the memory bus */
- cmmem: cmosc@24M {
+ cmmem: cmosc@24m {
compatible = "arm,syscon-icst525-integratorcp-cm-mem";
#clock-cells = <0>;
lock-offset = <0x14>;
@@ -110,7 +110,7 @@
};
/* Auxilary oscillator on the core module, clocks the CLCD */
- auxosc: auxosc@24M {
+ auxosc: auxosc@24m {
compatible = "arm,syscon-icst525";
#clock-cells = <0>;
lock-offset = <0x14>;
@@ -119,7 +119,7 @@
};
/* The KMI clock is the 24 MHz oscillator divided to 8MHz */
- kmiclk: kmiclk@1M {
+ kmiclk: kmiclk@1m {
#clock-cells = <0>;
compatible = "fixed-factor-clock";
clock-div = <3>;
@@ -128,7 +128,7 @@
};
/* The timer clock is the 24 MHz oscillator divided to 1MHz */
- timclk: timclk@1M {
+ timclk: timclk@1m {
#clock-cells = <0>;
compatible = "fixed-factor-clock";
clock-div = <24>;
Improve the DTS files by removing all the leading "0x" and zeros to fix the following dtc warnings: Warning (unit_address_format): Node /XXX unit name should not have leading "0x" and Warning (unit_address_format): Node /XXX unit name should not have leading 0s Converted using the following command: find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C For simplicity, two sed expressions were used to solve each warnings separately. To make the regex expression more robust a few other issues were resolved, namely setting unit-address to lower case, and adding a whitespace before the the opening curly brace: https://elinux.org/Device_Tree_Linux#Linux_conventions This will solve as a side effect warning: Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>" This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation") Reported-by: David Daney <ddaney@caviumnetworks.com> Suggested-by: Rob Herring <robh@kernel.org> Signed-off-by: Mathieu Malaterre <malat@debian.org> --- arch/arm/boot/dts/integratorap.dts | 14 +++++++------- arch/arm/boot/dts/integratorcp.dts | 20 ++++++++++---------- 2 files changed, 17 insertions(+), 17 deletions(-)