diff mbox

arm64: allwinner: a64-amarula-relic: Enable AP6330 WiFi support

Message ID 20180529172238.9718-1-jagan@amarulasolutions.com (mailing list archive)
State New, archived
Headers show

Commit Message

Jagan Teki May 29, 2018, 5:22 p.m. UTC 
Enable AP6330 WiFi/BT combo chip on Amarula A64-Relic board:
- WiFi SDIO interface is connected to MMC1
- WiFi WL-PMU-EN pin connected to gpio PL2: attach to mmc-pwrseq
- WiFi WL-WAKE-AP pin connected to gpio PL3
- 32kHz external oscillator gate clock from RTC

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
 .../dts/allwinner/sun50i-a64-amarula-relic.dts     | 37 ++++++++++++++++++++++
 1 file changed, 37 insertions(+)

Comments

Maxime Ripard May 31, 2018, 9:39 a.m. UTC | #1 
Hi,

On Tue, May 29, 2018 at 10:52:38PM +0530, Jagan Teki wrote:
> +&rtc {
> +	clock-output-names = "rtc-osc32k", "rtc-osc32k-out";
> +	clocks = <&osc32k>;
> +	#clock-cells = <1>;
> +};

It should be in the DTSI

Maxime
diff mbox

Patch

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
index ce4a256ff086..a77b70ca88e3 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
@@ -21,12 +21,43 @@ 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* WL-PMU-EN: PL2 */
+	};
 };
 
 &ehci0 {
 	status = "okay";
 };
 
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	/*
+	 * Schematic shows both dldo4 and eldo1 connected for vcc-io-wifi, but
+	 * dldo4 connection shows DNP(Do Not Populate) and eldo1 connected with
+	 * 0Ohm register to vcc-io-wifi so eldo1 is used.
+	 */
+	vqmmc-supply = <&reg_eldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>;	/* WL-WAKE-AP: PL3 */
+		interrupt-names = "host-wake";
+	};
+};
+
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
@@ -170,6 +201,12 @@ 
 	regulator-name = "vcc-rtc";
 };
 
+&rtc {
+	clock-output-names = "rtc-osc32k", "rtc-osc32k-out";
+	clocks = <&osc32k>;
+	#clock-cells = <1>;
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;