@@ -31,6 +31,13 @@ config LORA_SX1276
help
Semtech SX1272/1276/1278
+config LORA_USI
+ tristate "USI WM-SG-SM-42 driver"
+ default y
+ depends on SERIAL_DEV_BUS
+ help
+ USI WM-SG-SM-42
+
config LORA_WIMOD
tristate "IMST WiMOD driver"
default y
@@ -16,5 +16,8 @@ lora-rn2483-y += rn2483_cmd.o
obj-$(CONFIG_LORA_SX1276) += lora-sx1276.o
lora-sx1276-y := sx1276.o
+obj-$(CONFIG_LORA_USI) += lora-usi.o
+lora-usi-y := usi.o
+
obj-$(CONFIG_LORA_WIMOD) += lora-wimod.o
lora-wimod-y := wimod.o
new file mode 100644
@@ -0,0 +1,411 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * USI WM-SG-SM-42
+ *
+ * Copyright (c) 2017-2018 Andreas Färber
+ */
+
+#include <linux/lora.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/of.h>
+#include <linux/serdev.h>
+#include <linux/lora/dev.h>
+
+struct usi_device {
+ struct serdev_device *serdev;
+
+ int mode;
+
+ char rx_buf[4096];
+ int rx_len;
+
+ struct completion prompt_recv_comp;
+ struct completion tx_event_recv_comp;
+};
+
+static bool usi_cmd_ok(const char *resp)
+{
+ int len = strlen(resp);
+
+ return (len == 4 && !strcmp(resp, "OK\r\n")) ||
+ (len >= 6 && !strcmp(resp + len - 6, "\r\nOK\r\n"));
+}
+
+static int usi_send_command(struct usi_device *usidev, const char *cmd, char **data, unsigned long timeout)
+{
+ struct serdev_device *sdev = usidev->serdev;
+ const char cr = '\r';
+ int cmd_len, resp_len;
+ char *resp;
+
+ cmd_len = strlen(cmd);
+ serdev_device_write_buf(sdev, cmd, cmd_len);
+ serdev_device_write_buf(sdev, &cr, 1);
+
+ timeout = wait_for_completion_timeout(&usidev->prompt_recv_comp, timeout);
+ if (!timeout)
+ return -ETIMEDOUT;
+
+ resp = usidev->rx_buf;
+ resp_len = usidev->rx_len;
+ if (!strncmp(resp, cmd, cmd_len) && resp[cmd_len] == '\r') {
+ dev_dbg(&sdev->dev, "Skipping echo\n");
+ resp += cmd_len + 1;
+ resp_len -= cmd_len + 1;
+ }
+ dev_dbg(&sdev->dev, "Received: '%s'\n", resp);
+ if (data)
+ *data = kstrdup(resp, GFP_KERNEL);
+
+ usidev->rx_len = 0;
+ reinit_completion(&usidev->prompt_recv_comp);
+
+ return 0;
+}
+
+static int usi_simple_cmd(struct usi_device *usidev, const char *cmd, unsigned long timeout)
+{
+ char *resp;
+ int ret;
+
+ ret = usi_send_command(usidev, cmd, &resp, timeout);
+ if (ret)
+ return ret;
+
+ if (strcmp(resp, "OK\r\n") == 0) {
+ kfree(resp);
+ return 0;
+ }
+
+ kfree(resp);
+
+ return -EINVAL;
+}
+
+static int usi_cmd_reset(struct usi_device *usidev)
+{
+ int ret;
+
+ ret = usi_send_command(usidev, "ATZ", NULL, HZ);
+ if (ret)
+ return ret;
+
+ mdelay(1000);
+
+ return 0;
+}
+
+static int usi_cmd_read_reg(struct usi_device *usidev, u8 addr, u8 *val)
+{
+ char *cmd;
+ char *resp;
+ char *sz;
+ int ret;
+
+ cmd = kasprintf(GFP_KERNEL, "AT+RREG=0x%02x", (int)addr);
+ if (!cmd)
+ return -ENOMEM;
+
+ ret = usi_send_command(usidev, cmd, &resp, HZ);
+ if (ret) {
+ kfree(cmd);
+ return ret;
+ }
+ if (!usi_cmd_ok(resp)) {
+ kfree(resp);
+ kfree(cmd);
+ return -EINVAL;
+ }
+ resp[strlen(resp) - 6] = '\0';
+ sz = resp;
+ if (strstarts(sz, "+Reg="))
+ sz += 5;
+ if (strncasecmp(sz, cmd + 8, 4) == 0 && strstarts(sz + 4, ", "))
+ sz += 6;
+
+ kfree(cmd);
+
+ dev_dbg(&usidev->serdev->dev, "Parsing '%s'\n", sz);
+ ret = kstrtou8(sz, 0, val);
+ if (ret) {
+ kfree(resp);
+ return ret;
+ }
+
+ kfree(resp);
+
+ return 0;
+}
+
+static int usi_receive_buf(struct serdev_device *sdev, const u8 *data, size_t count)
+{
+ struct usi_device *usidev = serdev_device_get_drvdata(sdev);
+ size_t i = 0;
+ int len = 0;
+
+ dev_dbg(&sdev->dev, "Receive (%d)\n", (int)count);
+
+ for (i = 0; i < count; i++) {
+ dev_dbg(&sdev->dev, "Receive: 0x%02x\n", (int)data[i]);
+ }
+ i = 0;
+
+ if (completion_done(&usidev->prompt_recv_comp) ||
+ completion_done(&usidev->tx_event_recv_comp)) {
+ dev_info(&sdev->dev, "RX waiting on completion\n");
+ return 0;
+ }
+ if (usidev->rx_len == sizeof(usidev->rx_buf) - 1) {
+ dev_warn(&sdev->dev, "RX buffer full\n");
+ return 0;
+ }
+
+ i = min(count, sizeof(usidev->rx_buf) - 1 - usidev->rx_len);
+ if (i > 0) {
+ memcpy(&usidev->rx_buf[usidev->rx_len], data, i);
+ usidev->rx_len += i;
+ len += i;
+ }
+ if (usidev->rx_len >= 3 && strncmp(&usidev->rx_buf[usidev->rx_len - 3], "\r# ", 3) == 0) {
+ usidev->rx_len -= 3;
+ usidev->rx_buf[usidev->rx_len] = '\0';
+ complete(&usidev->prompt_recv_comp);
+ } else if (usidev->rx_len > 7 && strstarts(usidev->rx_buf, "+RCV") &&
+ strncmp(&usidev->rx_buf[usidev->rx_len - 2], "\r\n", 2) == 0) {
+ usidev->rx_buf[usidev->rx_len - 2] = '\0';
+ dev_info(&sdev->dev, "RCV event: '%s'\n", usidev->rx_buf + 4);
+ usidev->rx_len = 0;
+ } else if (usidev->rx_len > 6 && strstarts(usidev->rx_buf, "+TX: ") &&
+ strncmp(&usidev->rx_buf[usidev->rx_len - 2], "\r\n", 2) == 0) {
+ usidev->rx_buf[usidev->rx_len - 2] = '\0';
+ dev_info(&sdev->dev, "TX event: '%s'\n", usidev->rx_buf + 5);
+ complete(&usidev->tx_event_recv_comp);
+ }
+
+ return len;
+}
+
+static const struct serdev_device_ops usi_serdev_client_ops = {
+ .receive_buf = usi_receive_buf,
+};
+
+static int usi_probe(struct serdev_device *sdev)
+{
+ struct usi_device *usidev;
+ //unsigned long timeout;
+ char *resp;
+ u8 val;
+ int ret;
+
+ dev_info(&sdev->dev, "Probing");
+
+ usidev = devm_kzalloc(&sdev->dev, sizeof(struct usi_device), GFP_KERNEL);
+ if (!usidev)
+ return -ENOMEM;
+
+ usidev->serdev = sdev;
+ usidev->mode = -1;
+ init_completion(&usidev->prompt_recv_comp);
+ init_completion(&usidev->tx_event_recv_comp);
+ serdev_device_set_drvdata(sdev, usidev);
+
+ ret = serdev_device_open(sdev);
+ if (ret) {
+ dev_err(&sdev->dev, "Failed to open (%d)", ret);
+ return ret;
+ }
+
+ serdev_device_set_baudrate(sdev, 115200);
+ serdev_device_set_flow_control(sdev, false);
+ serdev_device_set_client_ops(sdev, &usi_serdev_client_ops);
+
+ ret = usi_cmd_reset(usidev);
+ if (ret)
+ dev_warn(&sdev->dev, "Reset failed\n");
+
+ ret = usi_send_command(usidev, "ATE=0", NULL, HZ);
+ if (ret)
+ dev_warn(&sdev->dev, "ATE failed\n");
+
+ /* Dropped in firmware 2.8 */
+ ret = usi_send_command(usidev, "ATI", &resp, HZ);
+ if (!ret) {
+ if (usi_cmd_ok(resp)) {
+ resp[strlen(resp) - 6] = '\0';
+ dev_info(&sdev->dev, "Firmware '%s'\n", resp);
+ }
+ kfree(resp);
+ }
+
+ ret = usi_send_command(usidev, "AT+DEFMODE", &resp, HZ);
+ if (ret) {
+ dev_err(&sdev->dev, "Checking DEFMODE failed (%d)\n", ret);
+ serdev_device_close(sdev);
+ return ret;
+ }
+ if (usi_cmd_ok(resp)) {
+ resp[strlen(resp) - 6] = '\0';
+ dev_info(&sdev->dev, "Default mode '%s'\n", resp);
+ if (!strcmp(resp, "MFG_WAN_MODE"))
+ usidev->mode = 6;
+ else if (!strcmp(resp, "MFG_TEST_IDLE"))
+ usidev->mode = 0;
+ else if (!strcmp(resp, "MFG_TX_TONE"))
+ usidev->mode = 1;
+ else if (!strcmp(resp, "MFG_TX_PACKET"))
+ usidev->mode = 2;
+ else if (!strcmp(resp, "MFG_ERROR_LESS_ARGUMENETS"))
+ usidev->mode = 3;
+ else if (!strcmp(resp, "MFG_TX_TEXT"))
+ usidev->mode = 4;
+ else if (!strcmp(resp, "MFG_TEST_STOP"))
+ usidev->mode = 5;
+ }
+ kfree(resp);
+
+ if (usidev->mode != 3) {
+ ret = usi_simple_cmd(usidev, "AT+DEFMODE=3", HZ);
+ if (ret) {
+ dev_err(&sdev->dev, "Setting DEFMODE failed (%d)\n", ret);
+ serdev_device_close(sdev);
+ return ret;
+ }
+
+#if 1
+ ret = usi_simple_cmd(usidev, "AT+WDCT", 5 * HZ);
+ if (ret) {
+ dev_err(&sdev->dev, "Writing DCT failed (%d)\n", ret);
+ serdev_device_close(sdev);
+ return ret;
+ }
+
+ ret = usi_cmd_reset(usidev);
+ if (ret) {
+ dev_err(&sdev->dev, "Reset failed\n");
+ serdev_device_close(sdev);
+ return ret;
+ }
+
+ ret = usi_send_command(usidev, "ATE=0", NULL, HZ);
+ if (ret)
+ dev_warn(&sdev->dev, "ATE failed\n");
+#endif
+
+ usidev->mode = -1;
+ ret = usi_send_command(usidev, "AT+DEFMODE", &resp, HZ);
+ if (ret) {
+ dev_err(&sdev->dev, "Checking DEFMODE failed (%d)\n", ret);
+ serdev_device_close(sdev);
+ return ret;
+ }
+ if (usi_cmd_ok(resp)) {
+ resp[strlen(resp) - 6] = '\0';
+ dev_info(&sdev->dev, "Default mode '%s'\n", resp);
+ if (!strcmp(resp, "MFG_WAN_MODE")) {
+ usidev->mode = 6;
+ }
+ }
+ kfree(resp);
+ }
+
+ ret = usi_send_command(usidev, "AT+VER", &resp, HZ);
+ if (!ret) {
+ if (usi_cmd_ok(resp)) {
+ resp[strlen(resp) - 6] = '\0';
+ dev_info(&sdev->dev, "LoRaWAN version '%s'\n",
+ (strstarts(resp, "+VER=")) ? (resp + 5) : resp);
+ }
+ kfree(resp);
+ }
+
+ ret = usi_simple_cmd(usidev, "AT+RF=20,868000000,7,0,1,0,8,0,0,0", HZ);
+ if (ret) {
+ dev_err(&sdev->dev, "AT+RF failed (%d)\n", ret);
+ serdev_device_close(sdev);
+ return ret;
+ }
+
+ /*ret = usi_simple_cmd(usidev, "AT+TXT=1,deadbeef", 2 * HZ);
+ if (ret) {
+ dev_err(&sdev->dev, "TX failed (%d)\n", ret);
+ serdev_device_close(sdev);
+ return ret;
+ }
+
+ timeout = wait_for_completion_timeout(&usidev->tx_event_recv_comp, 5 * HZ);
+ if (!timeout) {
+ serdev_device_close(sdev);
+ return -ETIMEDOUT;
+ }
+ usidev->rx_len = 0;
+ reinit_completion(&usidev->tx_event_recv_comp);*/
+
+ ret = usi_cmd_read_reg(usidev, 0x42, &val);
+ if (!ret) {
+ dev_info(&sdev->dev, "SX1272 VERSION 0x%02x\n", (int)val);
+ }
+
+ ret = usi_cmd_read_reg(usidev, 0x39, &val);
+ if (!ret) {
+ dev_info(&sdev->dev, "SX1272 SyncWord 0x%02x\n", (int)val);
+ }
+
+ ret = usi_cmd_read_reg(usidev, 0x01, &val);
+ if (!ret) {
+ dev_info(&sdev->dev, "SX1272 OpMode 0x%02x\n", (int)val);
+ }
+
+ dev_info(&sdev->dev, "Done.");
+
+ return 0;
+}
+
+static void usi_remove(struct serdev_device *sdev)
+{
+ struct usi_device *usidev = serdev_device_get_drvdata(sdev);
+
+ usi_send_command(usidev, "ATE=1\r", NULL, HZ);
+
+ serdev_device_close(sdev);
+
+ dev_info(&sdev->dev, "Removed\n");
+}
+
+static const struct of_device_id usi_of_match[] = {
+ { .compatible = "usi,wm-sg-sm-42" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, usi_of_match);
+
+static struct serdev_device_driver usi_serdev_driver = {
+ .probe = usi_probe,
+ .remove = usi_remove,
+ .driver = {
+ .name = "usi",
+ .of_match_table = usi_of_match,
+ },
+};
+
+static int __init usi_init(void)
+{
+ int ret;
+
+ ret = serdev_device_driver_register(&usi_serdev_driver);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static void __exit usi_exit(void)
+{
+ serdev_device_driver_unregister(&usi_serdev_driver);
+}
+
+module_init(usi_init);
+module_exit(usi_exit);
+
+MODULE_DESCRIPTION("USI WM-SG-SM-42 serdev driver");
+MODULE_AUTHOR("Andreas Färber <afaerber@suse.de>");
+MODULE_LICENSE("GPL");
The USI WM-SG-SM-42 offers a UART based AT command interface. Cc: Dollar Chen (陳義元) <dollar.chen@wtmec.com> Signed-off-by: Andreas Färber <afaerber@suse.de> --- drivers/net/lora/Kconfig | 7 + drivers/net/lora/Makefile | 3 + drivers/net/lora/usi.c | 411 ++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 421 insertions(+) create mode 100644 drivers/net/lora/usi.c