new file mode 100644
@@ -0,0 +1,6 @@
+CZ.NIC's Turris Mox SOHO router Device Tree Bindings
+----------------------------------------------------
+
+Required root node property:
+
+compatible: must contain "cznic,turris-mox"
@@ -1382,6 +1382,7 @@ ARM/CZ.NIC TURRIS MOX SUPPORT
M: Marek Behun <marek.behun@nic.cz>
W: http://mox.turris.cz
S: Maintained
+F: arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
F: include/mfd/moxtet.h
F: drivers/gpio/gpio-moxtet.c
F: drivers/mfd/moxtet.c
@@ -2,6 +2,7 @@
# Mvebu SoC Family
dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
new file mode 100644
@@ -0,0 +1,229 @@
+// SPDX-License-Identifier: GPL-2.0+ or X11
+/*
+ * Device Tree file for CZ.NIC Turris Mox Board
+ * 2018 by Marek Behun <marek.behun@nic.cz>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "armada-372x.dtsi"
+
+/ {
+ model = "CZ.NIC Turris Mox Board";
+ compatible = "cznic,turris-mox", "marvell,armada3720",
+ "marvell,armada3710";
+
+ aliases {
+ spi0 = &spi0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ red {
+ gpios = <&gpiosb 21 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ button@0 {
+ label = "reset";
+ linux,code = <BTN_MISC>;
+ gpios = <&gpiosb 20 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ exp_usb3_vbus: usb3-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb3-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&gpiosb 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb3_phy: usb3-phy {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <&exp_usb3_vbus>;
+ };
+
+ vsdc_reg: regulator@1 {
+ compatible = "regulator-gpio";
+ regulator-name = "vsdc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+
+ gpios = <&gpiosb 23 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ enable-active-high;
+ };
+
+ vsdio_reg: regulator@2 {
+ compatible = "regulator-gpio";
+ regulator-name = "vsdio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+
+ gpios = <&gpiosb 22 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ enable-active-high;
+ };
+};
+
+&pinctrl_nb {
+ spi_cs1_pins: spi-cs1-pins {
+ groups = "spi_cs1";
+ function = "spi";
+ };
+
+ sdio0_pins: sdio0-pins {
+ groups = "sdio0";
+ function = "sdio";
+ };
+};
+
+&pinctrl_sb {
+ sdio_sb_pins: sdio-sb-pins {
+ groups = "sdio_sb";
+ function = "sdio";
+ };
+
+ smi_pins: smi-pins {
+ groups = "smi";
+ function = "smi";
+ };
+
+ pcie_pins: pcie1-pins {
+ groups = "pcie1";
+ function = "gpio";
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "okay";
+
+ rtc@6f {
+ compatible = "microchip,mcp7940x";
+ reg = <0x6f>;
+ };
+};
+
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_pins>;
+ status = "okay";
+ max-link-speed = <2>;
+
+ /* this shall be enabled by u-boot if the PCIe module is present */
+ status = "disabled";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+ð0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii-id";
+ phy = <&phy1>;
+ status = "okay";
+};
+
+&mdio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&smi_pins>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&sdhci0 {
+ wp-inverted;
+ bus-width = <4>;
+ cd-gpios = <&gpionb 10 GPIO_ACTIVE_HIGH>;
+ vqmmc-supply = <&vsdc_reg>;
+ marvell,pad-type = "sd";
+ status = "okay";
+};
+
+&sdhci1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio0_pins &sdio_sb_pins>;
+ non-removable;
+ bus-width = <4>;
+ marvell,pad-type = "sd";
+ vqmmc-supply = <&vsdio_reg>;
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_quad_pins &spi_cs1_pins>;
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <2000000>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x3f0000>;
+ };
+
+ partition@3f0000 {
+ label = "u-boot-env";
+ reg = <0x180000 0x10000>;
+ };
+
+ partition@400000 {
+ label = "Rescue system";
+ reg = <0x190000 0x670000>;
+ };
+ };
+
+ moxtet@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "cznic,moxtet";
+ reg = <1>;
+ spi-max-frequency = <1000000>;
+ spi-cpol;
+ spi-cpha;
+ };
+};
+
+&usb3 {
+ status = "okay";
+ usb-phy = <&usb3_phy>;
+};
This adds basic support for the Turris Mox board from CZ.NIC. Turris Mox is as modular router based on the Armada 3720 SOC (same as EspressoBin). The basic module can be extended by different modules. When those modules are connected, U-Boot shall patch this basic device-tree with nodes corresponding to those modules. Signed-off-by: Marek Behun <marek.behun@nic.cz> --- .../arm/marvell/armada-3720-turris-mox.txt | 6 + MAINTAINERS | 1 + arch/arm64/boot/dts/marvell/Makefile | 1 + .../boot/dts/marvell/armada-3720-turris-mox.dts | 229 +++++++++++++++++++++ 4 files changed, 237 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts