@@ -12,6 +12,7 @@
#include <linux/clk.h>
#include <linux/completion.h>
+#include <linux/delay.h>
#include <linux/err.h>
#include <linux/errno.h>
#include <linux/i2c.h>
@@ -115,6 +116,9 @@
/* 0x18 : I2CD Slave Device Address Register */
#define ASPEED_I2CD_DEV_ADDR_MASK GENMASK(6, 0)
+/* Busy checking */
+#define ASPEED_I2C_BUS_BUSY_CHECK_INTERVAL_US (10 * 1000)
+
enum aspeed_i2c_master_state {
ASPEED_I2C_MASTER_INACTIVE,
ASPEED_I2C_MASTER_START,
@@ -156,6 +160,8 @@ struct aspeed_i2c_bus {
int cmd_err;
/* Protected only by i2c_lock_bus */
int master_xfer_result;
+ /* Multi-master */
+ bool multi_master;
#if IS_ENABLED(CONFIG_I2C_SLAVE)
struct i2c_client *slave;
enum aspeed_i2c_slave_state slave_state;
@@ -596,27 +602,42 @@ static irqreturn_t aspeed_i2c_bus_irq(int irq, void *dev_id)
return irq_remaining ? IRQ_NONE : IRQ_HANDLED;
}
+static int aspeed_i2c_check_bus_busy(struct aspeed_i2c_bus *bus)
+{
+ ktime_t timeout;
+
+ if (bus->multi_master) {
+ might_sleep();
+ timeout = ktime_add_ms(ktime_get(),
+ jiffies_to_msecs(bus->adap.timeout));
+ }
+
+ for (;;) {
+ if (!(readl(bus->base + ASPEED_I2C_CMD_REG) &
+ ASPEED_I2CD_BUS_BUSY_STS) &&
+ bus->slave_state == ASPEED_I2C_SLAVE_STOP)
+ return 0;
+ if (!bus->multi_master)
+ break;
+ if (ktime_compare(ktime_get(), timeout) > 0)
+ break;
+ usleep_range((ASPEED_I2C_BUS_BUSY_CHECK_INTERVAL_US >> 2) + 1,
+ ASPEED_I2C_BUS_BUSY_CHECK_INTERVAL_US);
+ }
+
+ return aspeed_i2c_recover_bus(bus);
+}
+
static int aspeed_i2c_master_xfer(struct i2c_adapter *adap,
struct i2c_msg *msgs, int num)
{
struct aspeed_i2c_bus *bus = i2c_get_adapdata(adap);
unsigned long time_left, flags;
- int ret = 0;
- spin_lock_irqsave(&bus->lock, flags);
- bus->cmd_err = 0;
-
- /* If bus is busy, attempt recovery. We assume a single master
- * environment.
- */
- if (readl(bus->base + ASPEED_I2C_CMD_REG) & ASPEED_I2CD_BUS_BUSY_STS) {
- spin_unlock_irqrestore(&bus->lock, flags);
- ret = aspeed_i2c_recover_bus(bus);
- if (ret)
- return ret;
- spin_lock_irqsave(&bus->lock, flags);
- }
+ if (aspeed_i2c_check_bus_busy(bus))
+ return -EAGAIN;
+ spin_lock_irqsave(&bus->lock, flags);
bus->cmd_err = 0;
bus->msgs = msgs;
bus->msgs_index = 0;
@@ -827,7 +848,9 @@ static int aspeed_i2c_init(struct aspeed_i2c_bus *bus,
if (ret < 0)
return ret;
- if (!of_property_read_bool(pdev->dev.of_node, "multi-master"))
+ if (of_property_read_bool(pdev->dev.of_node, "multi-master"))
+ bus->multi_master = true;
+ else
fun_ctrl_reg |= ASPEED_I2CD_MULTI_MASTER_DIS;
/* Enable Master Mode */
In multi-master environment, this driver's master cannot know exactly when peer master sends data to this driver's slave so a case can be happened that this master tries to send data through the master_xfer function but slave data from peer master is still being processed by this driver. To prevent any state corruption in the case, this patch adds checking code if any slave operation is ongoing and it waits up to the bus timeout duration before starting a master_xfer operation. Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com> --- drivers/i2c/busses/i2c-aspeed.c | 53 +++++++++++++++++++++++---------- 1 file changed, 38 insertions(+), 15 deletions(-)