@@ -778,6 +778,13 @@ dtb-$(CONFIG_ARCH_ACTIONS) += \
owl-s500-sparky.dtb
dtb-$(CONFIG_ARCH_PRIMA2) += \
prima2-evb.dtb
+dtb-$(CONFIG_ARCH_PXA) += \
+ pxa300-raumfeld-connector.dtb \
+ pxa300-raumfeld-controller.dtb \
+ pxa300-raumfeld-speaker-s.dtb \
+ pxa300-raumfeld-speaker-m.dtb \
+ pxa300-raumfeld-speaker-l.dtb \
+ pxa300-raumfeld-speaker-one.dtb
dtb-$(CONFIG_ARCH_OXNAS) += \
ox810se-wd-mbwe.dtb \
ox820-cloudengines-pogoplug-series-3.dtb
new file mode 100644
@@ -0,0 +1,405 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "pxa3xx.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ /* Will be overridden by bootloader */
+ hw-revision = <0>;
+
+ chosen {
+ bootargs = "root=ubi0:RootFS rootfstype=ubifs rw ubi.mtd=3";
+ stdout-path = &ffuart;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0xa0000000 0x8000000>; /* 128 MB */
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3-fixed-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8-fixed-supply";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_va_5v0: regulator-va-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "va-5v0-fixed-supply";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio 124 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ ssp_dai0: ssp-dai0 {
+ compatible = "mrvl,pxa-ssp-dai";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ssp0_dai_pins>;
+ port = <&ssp1>;
+ #sound-dai-cells = <0>;
+ dmas = <&pdma 13 3
+ &pdma 14 3>;
+ dma-names = "rx", "tx";
+ clock-names = "extclk";
+ };
+
+ ssp_dai1: ssp-dai1 {
+ compatible = "mrvl,pxa-ssp-dai";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ssp1_dai_pins>;
+ port = <&ssp2>;
+ #sound-dai-cells = <0>;
+ dmas = <&pdma 15 3
+ &pdma 16 3>;
+ dma-names = "rx", "tx";
+ clock-names = "extclk";
+ };
+
+ spi: spi {
+ compatible = "spi-gpio";
+ #address-cells = <0x1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_pins>;
+ gpio-sck = <&gpio 95 GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio 98 GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&gpio 97 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <
+ &gpio 34 GPIO_ACTIVE_HIGH
+ &gpio 125 GPIO_ACTIVE_HIGH
+ &gpio 96 GPIO_ACTIVE_HIGH
+ >;
+ num-chipselects = <3>;
+
+ dac: dac@2 {
+ compatible = "ti,dac7512";
+ reg = <2>;
+ spi-max-frequency = <1000000>;
+ vcc-supply = <®_3v3>;
+ };
+ };
+
+ keys: gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_pins>;
+
+ on-off {
+ label = "on_off button";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_F6>;
+ };
+
+ rescue-boot {
+ label = "rescue boot button";
+ gpios = <&gpio 115 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_F4>;
+ };
+
+ setup {
+ label = "setup";
+ gpios = <&gpio 119 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_F3>;
+ };
+ };
+
+ rotary: rotary-encoder {
+ compatible = "rotary-encoder";
+ gpios = <
+ &gpio 19 GPIO_ACTIVE_LOW
+ &gpio 20 GPIO_ACTIVE_HIGH
+ >;
+ linux,axis = <REL_X>;
+ rotary-encoder,relative-axis;
+ };
+
+ leds: leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_a &led_pins_b>;
+
+ left {
+ label = "raumfeld:1";
+ gpios = <&gpio 36 GPIO_ACTIVE_LOW>;
+ };
+
+ right {
+ label = "raumfeld:2";
+ gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-names = "default";
+ pinctrl-0 = <&poweroff_pins>;
+ gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ mmc0_pwrseq: mmc-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pwrseq_pins>;
+ reset-gpios = <
+ &gpio 113 GPIO_ACTIVE_LOW /* W2W_RESET */
+ &gpio 114 GPIO_ACTIVE_LOW /* W2W_PDN */
+ >;
+ };
+
+ ethernet: ethernet@10000000 {
+ compatible = "smsc,lan9115";
+ pinctrl-names = "default";
+ pinctrl-0 = <&smsc_pins &smsc_bus_pins>;
+ reg = <0x10000000 0x100000>;
+ phy-mode = "mii";
+ interrupt-parent = <&gpio>;
+ interrupts = <40 IRQ_TYPE_EDGE_FALLING>;
+ vdd33a-supply = <®_3v3>;
+ vddvario-supply = <®_1v8>;
+ reset-gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
+ reg-io-width = <4>;
+ smsc,save-mac-address;
+ smsc,irq-push-pull;
+ };
+};
+
+&ffuart {
+ status = "okay";
+};
+
+&pwri2c {
+ status = "okay";
+
+ max8660: regulator@34 {
+ compatible = "maxim,max8660";
+ reg = <0x34>;
+
+ regulators {
+ regulator-v3 {
+ regulator-compatible= "V3(DCDC)";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ regulator-v4 {
+ regulator-compatible= "V4(DCDC)";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ regulator-v5 {
+ regulator-compatible= "V5(LDO)";
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <2000000>;
+ };
+
+ reg_vcc_sdio: regulator-v6 {
+ regulator-compatible= "V6(LDO)";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ regulator-v7 {
+ regulator-compatible= "V7(LDO)";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+};
+
+&pxai2c1 {
+ status = "okay";
+ mrvl,i2c-fast-mode;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pxai2c1_pins>;
+};
+
+&ssp1 {
+ status = "okay";
+};
+
+&ssp2 {
+ status = "okay";
+};
+
+&nand_controller {
+ status = "okay";
+
+ nand@0 {
+ reg = <0>;
+ nand-rb = <0>;
+ nand-ecc-mode = "hw";
+ marvell,nand-keep-config;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "Bootloader";
+ reg = <0x0000000 0xa0000>;
+ read-only;
+ };
+
+ partition@a0000 {
+ label = "BootloaderEnvironment";
+ reg = <0x0a0000 0x20000>;
+ };
+
+ partition@c0000 {
+ label = "BootloaderSplashScreen";
+ reg = <0x0c0000 0x60000>;
+ };
+
+ partition@120000 {
+ label = "UBI";
+ reg = <0x120000 0x7ee0000>;
+ };
+ };
+ };
+};
+
+&usb0 {
+ status = "okay";
+ marvell,enable-port1;
+ marvell,port-mode = <2>; /* PMM_GLOBAL_MODE */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pxa3xx_ohci_pins>;
+};
+
+&mmc0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ pxa-mmc,detect-delay-ms = <200>;
+ vmmc-supply = <®_vcc_sdio>;
+ mmc-pwrseq = <&mmc0_pwrseq>;
+ non-removable;
+ bus-width = <4>;
+};
+
+&pinctrl {
+ poweroff_pins: poweroff-pins {
+ pinctrl-single,pins = <MFP_PIN_PXA300(16) MFP_AF0>;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT);
+ };
+
+ led_pins_a: led-pins-a {
+ pinctrl-single,pins = <MFP_PIN_PXA300(35) MFP_AF0>;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+
+ led_pins_b: led-pins-b {
+ pinctrl-single,pins = <MFP_PIN_PXA300(36) MFP_AF0>;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_DRIVE_HIGH);
+ };
+
+ pxai2c1_pins: pxai2c1-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(21) MFP_AF1 /* I2C_SCL */
+ MFP_PIN_PXA300(22) MFP_AF1 /* I2C_SDA */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_HIGH);
+ };
+
+ gpio_keys_pins: gpio-keys-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(14) MFP_AF0 /* SCK */
+ MFP_PIN_PXA300(115) MFP_AF0 /* MOSI */
+ MFP_PIN_PXA300(119) MFP_AF0 /* MISO */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT);
+ };
+
+ spi_pins: spi-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(95) MFP_AF0 /* SCK */
+ MFP_PIN_PXA300(97) MFP_AF0 /* MOSI */
+ MFP_PIN_PXA300(98) MFP_AF0 /* MISO */
+ MFP_PIN_PXA300(34) MFP_AF0 /* CS#0 */
+ MFP_PIN_PXA300(125) MFP_AF0 /* CS#1 */
+ MFP_PIN_PXA300(96) MFP_AF0 /* CS#2 */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+
+ pxa3xx_ohci_pins: pxa3xx-ohci-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300_2(0) MFP_AF1 /* USBHPEN */
+ MFP_PIN_PXA300_2(1) MFP_AF1 /* USBHPWR */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+
+ smsc_pins: smsc-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(39) MFP_AF0 /* RESET */
+ MFP_PIN_PXA300(40) MFP_AF0 /* IRQ */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+
+ smsc_bus_pins: smsc-bus-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(1) MFP_AF1 /* nCS2 */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT);
+ };
+
+ mmc0_pins: mmc0-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(3) MFP_AF4 /* MMC1_DAT0 */
+ MFP_PIN_PXA300(4) MFP_AF4 /* MMC1_DAT1 */
+ MFP_PIN_PXA300(5) MFP_AF4 /* MMC1_DAT2 */
+ MFP_PIN_PXA300(6) MFP_AF4 /* MMC1_DAT3 */
+ MFP_PIN_PXA300(7) MFP_AF4 /* MMC1_CLK */
+ MFP_PIN_PXA300(8) MFP_AF4 /* MMC1_CMD */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_DRIVE_HIGH);
+ };
+
+ mmc0_pwrseq_pins: mmc0-pwrseq-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(113) MFP_AF0 /* W2W_RESET */
+ MFP_PIN_PXA300(114) MFP_AF0 /* W2W_PDN */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT);
+ };
+
+ ssp0_dai_pins: ssp0-dai-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(85) MFP_AF1 /* SSP1_SCLK */
+ MFP_PIN_PXA300(86) MFP_AF1 /* SSP1_FRM */
+ MFP_PIN_PXA300(87) MFP_AF1 /* SSP1_TXD */
+ MFP_PIN_PXA300(88) MFP_AF1 /* SSP1_RXD */
+ MFP_PIN_PXA300(89) MFP_AF1 /* SSP1_EXTCLK */
+ MFP_PIN_PXA300(90) MFP_AF1 /* SSP1_SYSCLK */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+
+ ssp1_dai_pins: ssp1-dai-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(25) MFP_AF2 /* SSP2_SCLK */
+ MFP_PIN_PXA300(26) MFP_AF2 /* SSP2_FRM */
+ MFP_PIN_PXA300(27) MFP_AF2 /* SSP2_TXD */
+ MFP_PIN_PXA300(29) MFP_AF2 /* SSP2_EXTCLK */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+};
new file mode 100644
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include "pxa300-raumfeld-common.dtsi"
+#include "pxa300-raumfeld-tuneable-clock.dtsi"
+
+/ {
+ model = "Raumfeld Connector (PXA3xx)";
+ compatible = "raumfeld,raumfeld-connector-pxa303", "marvell,pxa300";
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "Raumfeld Connector";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ simple-audio-card,dai-link@0 {
+ reg = <0>;
+ format = "i2s";
+ bitclock-master = <&dailink_master_analog>;
+ frame-master = <&dailink_master_analog>;
+ mclk-fs = <256>;
+
+ dailink_master_analog: cpu {
+ sound-dai = <&ssp_dai0>;
+ };
+
+ codec {
+ sound-dai = <&cs4270>;
+ };
+ };
+
+ simple-audio-card,dai-link@1 {
+ reg = <1>;
+ format = "i2s";
+ bitclock-master = <&dailink_master_digital>;
+ frame-master = <&dailink_master_digital>;
+ mclk-fs = <256>;
+
+ dailink_master_digital: cpu {
+ sound-dai = <&ssp_dai1>;
+ };
+
+ codec {
+ sound-dai = <&ak4104>;
+ };
+ };
+ };
+};
+
+&ssp1 {
+ status = "okay";
+};
+
+&ssp2 {
+ status = "okay";
+};
+
+&spi {
+ ak4104: optical-transmitter@0 {
+ compatible = "asahi-kasei,ak4104";
+ reg = <0>;
+ vdd-supply = <®_3v3>;
+ spi-max-frequency = <5000000>;
+ reset-gpios = <&gpio 38 GPIO_ACTIVE_HIGH>;
+ #sound-dai-cells = <0>;
+ };
+};
+
+&rotary {
+ status = "disabled";
+};
new file mode 100644
@@ -0,0 +1,266 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include "pxa300-raumfeld-common.dtsi"
+
+/ {
+ model = "Raumfeld Controller (PXA3xx)";
+ compatible = "raumfeld,raumfeld-controller-pxa303", "marvell,pxa300";
+
+ reg_vbatt: regulator-vbatt {
+ compatible = "regulator-fixed";
+ regulator-name = "vbatt-fixed-supply";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-always-on;
+ };
+
+ lcd_supply: regulator-va-tft {
+ compatible = "regulator-fixed";
+ regulator-name = "va-tft-fixed-supply";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio 33 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ onewire {
+ compatible = "w1-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&w1_pins>;
+ gpios = <
+ &gpio 126 GPIO_OPEN_DRAIN /* W1 I/O */
+ &gpio 105 GPIO_ACTIVE_HIGH /* pullup */
+ >;
+
+ w1_ds2760: slave-ds2760 {
+ compatible = "maxim,ds2760";
+ power-supplies = <&charger>;
+ };
+ };
+
+ charger: charger {
+ compatible = "gpio-charger";
+ charger-type = "mains";
+ gpios = <&gpio 101 GPIO_ACTIVE_LOW>;
+ };
+
+ /*
+ * One of the following two will be set to "okay" by the bootloader,
+ * depending on the hardware revision.
+ */
+ backlight-controller-pwm {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins>;
+ pwms = <&pwm0 10000>;
+ power-supply = <®_vbatt>;
+ status = "disabled";
+
+ brightness-levels = <
+ 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100
+ >;
+ default-brightness-level = <100>;
+ };
+
+ backlight-controller {
+ compatible = "lltc,lt3593";
+ pinctrl-names = "default";
+ pinctrl-0 = <<3593_pins>;
+ lltc,ctrl-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+
+ led {
+ label = "backlight";
+ default-state = "on";
+ };
+ };
+};
+
+®_va_5v0 {
+ status = "disabled";
+};
+
+ðernet {
+ status = "disabled";
+};
+
+&leds {
+ status = "disabled";
+};
+
+&dac {
+ status = "disabled";
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&keys {
+ dock-detect {
+ label = "dock detect";
+ gpios = <&gpio 116 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_F5>;
+ };
+};
+
+&spi {
+ accelerometer@1 {
+ compatible = "st,lis302dl-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&lis302_pins>;
+ reg = <1>;
+ spi-max-frequency = <1000000>;
+ interrupt-parent = <&gpio>;
+ interrupts = <104 IRQ_TYPE_EDGE_FALLING>;
+
+ st,click-single-x;
+ st,click-single-y;
+ st,click-single-z;
+ st,click-thresh-x = <10>;
+ st,click-thresh-y = <10>;
+ st,click-thresh-z = <10>;
+ st,irq1-click;
+ st,irq2-click;
+ st,wakeup-x-lo;
+ st,wakeup-x-hi;
+ st,wakeup-y-lo;
+ st,wakeup-y-hi;
+ st,wakeup-z-lo;
+ st,wakeup-z-hi;
+ };
+};
+
+&lcdc {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdc_pins>;
+ lcd-supply = <&lcd_supply>;
+
+ port {
+ lcdc_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ bus-width = <16>;
+ };
+ };
+
+ panel {
+ compatible = "sharp,lq043t3dx0-panel";
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing {
+ clock-frequency = <9009000>;
+ pixelclk-active = <0>; /* negative edge */
+ hactive = <480>;
+ vactive = <272>;
+ hsync-len = <41>;
+ hback-porch = <2>;
+ hfront-porch = <1>;
+ vsync-len = <10>;
+ vback-porch = <3>;
+ vfront-porch = <1>;
+ };
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lcdc_out>;
+ };
+ };
+ };
+};
+
+&gcu {
+ status = "okay";
+};
+
+&pxai2c1 {
+ touchscreen@a {
+ compatible = "eeti,exc3000-i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&eeti_ts_pins>;
+ reg = <0xa>;
+ interrupt-parent = <&gpio>;
+ interrupts = <32 IRQ_TYPE_EDGE_RISING>;
+ attn-gpios = <&gpio 32 GPIO_ACTIVE_HIGH>;
+ touchscreen-inverted-y;
+ };
+};
+
+&pinctrl {
+ lis302_pins: lis302-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(104) MFP_AF0 /* IRQ */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+
+ eeti_ts_pins: eeti-ts-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(32) MFP_AF0 /* IRQ */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT);
+ };
+
+ lt3593_pins: lt3593-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(17) MFP_AF0 /* Backlight */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+
+ pwm0_pins: pwm0-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(17) MFP_AF1 /* PWM */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+
+ w1_pins: w1-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(126) MFP_AF0 /* PWM */
+ MFP_PIN_PXA300(105) MFP_AF0 /* PWM */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT);
+ };
+
+ lcdc_pins: lcdc-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(54) MFP_AF1 /* LDD_0 */
+ MFP_PIN_PXA300(55) MFP_AF1 /* LDD_1 */
+ MFP_PIN_PXA300(56) MFP_AF1 /* LDD_2 */
+ MFP_PIN_PXA300(57) MFP_AF1 /* LDD_3 */
+ MFP_PIN_PXA300(58) MFP_AF1 /* LDD_4 */
+ MFP_PIN_PXA300(59) MFP_AF1 /* LDD_5 */
+ MFP_PIN_PXA300(60) MFP_AF1 /* LDD_6 */
+ MFP_PIN_PXA300(61) MFP_AF1 /* LDD_7 */
+ MFP_PIN_PXA300(62) MFP_AF1 /* LDD_8 */
+ MFP_PIN_PXA300(63) MFP_AF1 /* LDD_9 */
+ MFP_PIN_PXA300(64) MFP_AF1 /* LDD_10 */
+ MFP_PIN_PXA300(65) MFP_AF1 /* LDD_11 */
+ MFP_PIN_PXA300(66) MFP_AF1 /* LDD_12 */
+ MFP_PIN_PXA300(67) MFP_AF1 /* LDD_13 */
+ MFP_PIN_PXA300(68) MFP_AF1 /* LDD_14 */
+ MFP_PIN_PXA300(69) MFP_AF1 /* LDD_15 */
+ MFP_PIN_PXA300(70) MFP_AF1 /* LDD_16 */
+ MFP_PIN_PXA300(71) MFP_AF1 /* LDD_17 */
+ MFP_PIN_PXA300(72) MFP_AF1 /* LCD_FCLK */
+ MFP_PIN_PXA300(73) MFP_AF1 /* LCD_LCLK */
+ MFP_PIN_PXA300(74) MFP_AF1 /* LCD_PCLK */
+ MFP_PIN_PXA300(75) MFP_AF1 /* LCD_BIAS */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+};
new file mode 100644
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include "pxa300-raumfeld-common.dtsi"
+#include "pxa300-raumfeld-tuneable-clock.dtsi"
+
+/ {
+ model = "Raumfeld Speaker L (PXA3xx)";
+ compatible = "raumfeld,raumfeld-speaker-l-pxa303", "marvell,pxa300";
+};
new file mode 100644
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include "pxa300-raumfeld-common.dtsi"
+#include "pxa300-raumfeld-tuneable-clock.dtsi"
+
+/ {
+ model = "Raumfeld Speaker M (PXA3xx)";
+ compatible = "raumfeld,raumfeld-speaker-m-pxa303", "marvell,pxa300";
+};
new file mode 100644
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include "pxa300-raumfeld-common.dtsi"
+
+/ {
+ model = "Raumfeld Speaker One (PXA3xx)";
+ compatible = "raumfeld,raumfeld-speaker-one-pxa303", "marvell,pxa300";
+
+ wm8782: wm8782 {
+ compatible = "wm8782";
+ #sound-dai-cells = <0>;
+ Vdd-supply = <®_3v3>;
+ Vdda-supply = <®_va_5v0>;
+ };
+
+ xo_11mhz: oscillator-11mhz {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <11289600>;
+ clock-accuracy = <100>;
+ };
+
+ xo_audio: clock-gate {
+ compatible = "gpio-gate-clock";
+ pinctrlnames = "default";
+ pinctrl-0 = <&xo_audio_pins>;
+ clocks = <&xo_11mhz>;
+ #clock-cells = <0>;
+ enable-gpios = <&gpio 111 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_va_30v0: regulator-va-30v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "va-30v0-fixed-supply";
+ regulator-min-microvolt = <30000000>;
+ regulator-max-microvolt = <30000000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "Raumfeld Speaker";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ simple-audio-card,dai-link@0 {
+ reg = <0>;
+ format = "i2s";
+ bitclock-master = <&dailink_master_analog_out>;
+ frame-master = <&dailink_master_analog_out>;
+ mclk-fs = <256>;
+
+ dailink_master_analog_out: cpu {
+ sound-dai = <&ssp_dai0>;
+ };
+
+ codec {
+ sound-dai = <&sta320>;
+ };
+ };
+
+ simple-audio-card,dai-link@1 {
+ reg = <1>;
+ format = "i2s";
+ bitclock-master = <&dailink_master_analog_in>;
+ frame-master = <&dailink_master_analog_in>;
+ mclk-fs = <256>;
+
+ dailink_master_analog_in: cpu {
+ sound-dai = <&ssp_dai0>;
+ };
+
+ codec {
+ sound-dai = <&wm8782>;
+ };
+ };
+ };
+};
+
+&ssp_dai0 {
+ clocks = <&xo_audio>;
+};
+
+&spi {
+ dac@2 {
+ compatible = "ti,dac7512";
+ reg = <2>;
+ spi-max-frequency = <1000000>;
+ vcc-supply = <®_3v3>;
+ };
+};
+
+&rotary {
+ status = "okay";
+};
+
+&pxai2c1 {
+ sta320: codec@1a {
+ compatible = "st,sta32x";
+ reg = <0x1a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sta320_pins>;
+ clocks = <&xo_audio>;
+ clock-names = "xti";
+ reset-gpios = <&gpio 120 GPIO_ACTIVE_HIGH>;
+ Vdda-supply = <®_3v3>;
+ Vdd3-supply = <®_3v3>;
+ Vcc-supply = <®_va_30v0>;
+ #sound-dai-cells = <0>;
+ st,thermal-warning-adjustment;
+ st,thermal-warning-recovery;
+ st,fault-detect-recovery;
+ st,drop-compensation-ns = <80>;
+ st,max-power-use-mpcc;
+ st,invalid-input-detect-mute;
+ /* 2 (half-bridge) and 1 (full-bridge) on-board power */
+ st,output-conf = /bits/ 8 <0x1>;
+ st,needs_esd_watchdog;
+ };
+};
+
+&pinctrl {
+ xo_audio_pins: xo-audio-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(111) MFP_AF0 /* ENABLE */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+
+ sta320_pins: sta320-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(120) MFP_AF0 /* CODEC_RESET */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT);
+ };
+};
new file mode 100644
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include "pxa300-raumfeld-common.dtsi"
+#include "pxa300-raumfeld-tuneable-clock.dtsi"
+
+/ {
+ model = "Raumfeld Speaker S (PXA3xx)";
+ compatible = "raumfeld,raumfeld-speaker-s-pxa303", "marvell,pxa300";
+};
new file mode 100644
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/clock/maxim,max9485.h>
+
+/ {
+ xo_27mhz: oscillator-27mhz {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <27000000>;
+ clock-accuracy = <100>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "Raumfeld Speaker";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ simple-audio-card,dai-link@0 {
+ reg = <0>;
+ format = "i2s";
+ bitclock-master = <&dailink_master_analog>;
+ frame-master = <&dailink_master_analog>;
+ mclk-fs = <256>;
+
+ dailink_master_analog: cpu {
+ sound-dai = <&ssp_dai0>;
+ };
+
+ codec {
+ sound-dai = <&cs4270>;
+ };
+ };
+ };
+};
+
+&ssp_dai0 {
+ clocks = <&max9485 MAX9485_CLKOUT1>;
+};
+
+&ssp_dai1 {
+ clocks = <&max9485 MAX9485_CLKOUT1>;
+};
+
+&pxai2c1 {
+ cs4270: codec@48 {
+ compatible = "cirrus,cs4270";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cs4270_pins>;
+ reg = <0x48>;
+ va-supply = <®_va_5v0>;
+ vd-supply = <®_3v3>;
+ vlc-supply = <®_3v3>;
+ reset-gpios = <&gpio 120 GPIO_ACTIVE_HIGH>;
+ #sound-dai-cells = <0>;
+ };
+
+ max9485: clock-generator@63 {
+ compatible = "maxim,max9485";
+ pinctrl-names = "default";
+ pinctrl-0 = <&max9485_pins>;
+ reg = <0x63>;
+ vdd-supply = <®_3v3>;
+ clock-names = "xclk";
+ clocks = <&xo_27mhz>;
+ reset-gpios = <&gpio 111 GPIO_ACTIVE_HIGH>;
+ #clock-cells = <1>;
+ };
+};
+
+&pinctrl {
+ cs4270_pins: cs4270-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(120) MFP_AF0 /* RESET */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+
+ max9485_pins: max9485-pins {
+ pinctrl-single,pins = <
+ MFP_PIN_PXA300(111) MFP_AF0 /* RESET */
+ >;
+ pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW);
+ };
+};
This patch adds a set of DTS files that support all PXA3xx based Raumfeld audio hardware devices. Common nodes are factored out into 'common' and 'tuneable-clock' include files to keep the top-level DTS files smaller. Signed-off-by: Daniel Mack <daniel@zonque.org> --- arch/arm/boot/dts/Makefile | 7 + arch/arm/boot/dts/pxa300-raumfeld-common.dtsi | 405 ++++++++++++++++++ .../boot/dts/pxa300-raumfeld-connector.dts | 73 ++++ .../boot/dts/pxa300-raumfeld-controller.dts | 266 ++++++++++++ .../boot/dts/pxa300-raumfeld-speaker-l.dts | 11 + .../boot/dts/pxa300-raumfeld-speaker-m.dts | 11 + .../boot/dts/pxa300-raumfeld-speaker-one.dts | 137 ++++++ .../boot/dts/pxa300-raumfeld-speaker-s.dts | 11 + .../dts/pxa300-raumfeld-tuneable-clock.dtsi | 85 ++++ 9 files changed, 1006 insertions(+) create mode 100644 arch/arm/boot/dts/pxa300-raumfeld-common.dtsi create mode 100644 arch/arm/boot/dts/pxa300-raumfeld-connector.dts create mode 100644 arch/arm/boot/dts/pxa300-raumfeld-controller.dts create mode 100644 arch/arm/boot/dts/pxa300-raumfeld-speaker-l.dts create mode 100644 arch/arm/boot/dts/pxa300-raumfeld-speaker-m.dts create mode 100644 arch/arm/boot/dts/pxa300-raumfeld-speaker-one.dts create mode 100644 arch/arm/boot/dts/pxa300-raumfeld-speaker-s.dts create mode 100644 arch/arm/boot/dts/pxa300-raumfeld-tuneable-clock.dtsi