diff mbox series

ARM: dts: vf610: Add ZII SSMB DTU board

Message ID 20190129231711.21844-1-andrew@lunn.ch (mailing list archive)
State New, archived
Headers show
Series ARM: dts: vf610: Add ZII SSMB DTU board | expand

Commit Message

Andrew Lunn Jan. 29, 2019, 11:17 p.m. UTC 
Add the Zodiac Digital Tapping Unit, a VF610 based network device with
5 Ethernet ports. One of these ports supports 1000Base-T2.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
 arch/arm/boot/dts/Makefile               |   1 +
 arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts | 311 +++++++++++++++++++++++
 2 files changed, 312 insertions(+)
 create mode 100644 arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts

Comments

Fabio Estevam Feb. 4, 2019, 1:22 p.m. UTC | #1 
Hi Andrew,

On Tue, Jan 29, 2019 at 9:17 PM Andrew Lunn <andrew@lunn.ch> wrote:
>
> Add the Zodiac Digital Tapping Unit, a VF610 based network device with
> 5 Ethernet ports. One of these ports supports 1000Base-T2.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Looks good. Only minor comments:

> +&i2c0 {
> +       clock-frequency = <100000>;
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_i2c0>;
> +       status = "okay";
> +
> +       gpio6: pca9505@22 {

Node names should be generic:

gpio-expander@22

> +               compatible = "nxp,pca9554";
> +               reg = <0x22>;
> +               gpio-controller;
> +               #gpio-cells = <2>;
> +       };
> +
> +       /* On SSMB */
> +       lm75@48 {

temperature-sensor@48

> +               compatible = "national,lm75";
> +               reg = <0x48>;
> +       };
> +
> +       /* On DSB */
> +       lm75@4d {

temperature-sensor@4d

> +               compatible = "national,lm75";
> +               reg = <0x4d>;
> +       };
> +
> +       at24c04@50 {

eeprom@50

> +               compatible = "atmel,24c04";
> +               reg = <0x50>;
> +               label = "nameplate";
> +       };
> +
> +       at24c04@52 {

eeprom@52

Reviewed-by: Fabio Estevam <festevam@gmail.com>
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index bd40148a15b2..df9c519a0433 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -599,6 +599,7 @@  dtb-$(CONFIG_SOC_VF610) += \
 	vf610-zii-dev-rev-b.dtb \
 	vf610-zii-dev-rev-c.dtb \
 	vf610-zii-scu4-aib.dtb \
+	vf610-zii-ssmb-dtu.dtb \
 	vf610-zii-ssmb-spu3.dtb
 dtb-$(CONFIG_ARCH_MXS) += \
 	imx23-evk.dtb \
diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts b/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
new file mode 100644
index 000000000000..1597bcb02cca
--- /dev/null
+++ b/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
@@ -0,0 +1,311 @@ 
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/*
+ * Device tree file for ZII's SSMB DTU board
+ *
+ * SSMB - SPU3 Switch Management Board
+ * DTU - Digital Tapping Unit
+ *
+ * Copyright (C) 2015-2019 Zodiac Inflight Innovations
+ *
+ * Based on an original 'vf610-twr.dts' which is Copyright 2015,
+ * Freescale Semiconductor, Inc.
+ */
+
+/dts-v1/;
+#include "vf610.dtsi"
+
+/ {
+	model = "ZII VF610 SSMB DTU Board";
+	compatible = "zii,vf610dtu", "zii,vf610dev", "fsl,vf610";
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pinctrl_leds_debug>;
+		pinctrl-names = "default";
+
+		led-debug {
+			label = "zii:green:debug1";
+			gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			max-brightness = <1>;
+		};
+	};
+
+	reg_vcc_3v3_mcu: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3_mcu";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&adc0 {
+	vref-supply = <&reg_vcc_3v3_mcu>;
+	status = "okay";
+};
+
+&adc1 {
+	vref-supply = <&reg_vcc_3v3_mcu>;
+	status = "okay";
+};
+
+&edma0 {
+	status = "okay";
+};
+
+&edma1 {
+	status = "okay";
+};
+
+&esdhc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc0>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&fec1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	status = "okay";
+
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
+
+	mdio1: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		switch0: switch0@0 {
+			compatible = "marvell,mv88e6190";
+			pinctrl-0 = <&pinctrl_gpio_switch0>;
+			pinctrl-names = "default";
+			reg = <0>;
+			eeprom-length = <65536>;
+			reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&gpio3>;
+			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&fec1>;
+
+					fixed-link {
+						speed = <100>;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "eth_cu_100_3";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "eth_cu_1000_4";
+				};
+
+				port@6 {
+					reg = <6>;
+					label = "eth_cu_1000_5";
+				};
+
+				port@8 {
+					reg = <8>;
+					label = "eth_cu_1000_1";
+				};
+
+				port@9 {
+					reg = <9>;
+					label = "eth_cu_1000_2";
+					phy-handle = <&phy9>;
+					phy-mode = "sgmii";
+					managed = "in-band-status";
+				};
+			};
+
+			mdio1 {
+				compatible = "marvell,mv88e6xxx-mdio-external";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy9: phy9@0 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					pinctrl-0 = <&pinctrl_gpio_phy9>;
+					pinctrl-names = "default";
+					interrupt-parent = <&gpio2>;
+					interrupts = <30 IRQ_TYPE_LEVEL_LOW>;
+					reg = <0>;
+				};
+			};
+		};
+	};
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c0>;
+	status = "okay";
+
+	gpio6: pca9505@22 {
+		compatible = "nxp,pca9554";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	/* On SSMB */
+	lm75@48 {
+		compatible = "national,lm75";
+		reg = <0x48>;
+	};
+
+	/* On DSB */
+	lm75@4d {
+		compatible = "national,lm75";
+		reg = <0x4d>;
+	};
+
+	at24c04@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		label = "nameplate";
+	};
+
+	at24c04@52 {
+		compatible = "atmel,24c04";
+		reg = <0x52>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_dspi1: dspi1grp {
+		fsl,pins = <
+			VF610_PAD_PTD5__DSPI1_CS0		0x1182
+			VF610_PAD_PTD4__DSPI1_CS1		0x1182
+			VF610_PAD_PTC6__DSPI1_SIN		0x1181
+			VF610_PAD_PTC7__DSPI1_SOUT		0x1182
+			VF610_PAD_PTC8__DSPI1_SCK		0x1182
+		>;
+	};
+
+	pinctrl_esdhc0: esdhc0grp {
+		fsl,pins = <
+			VF610_PAD_PTC0__ESDHC0_CLK		0x31ef
+			VF610_PAD_PTC1__ESDHC0_CMD		0x31ef
+			VF610_PAD_PTC2__ESDHC0_DAT0		0x31ef
+			VF610_PAD_PTC3__ESDHC0_DAT1		0x31ef
+			VF610_PAD_PTC4__ESDHC0_DAT2		0x31ef
+			VF610_PAD_PTC5__ESDHC0_DAT3		0x31ef
+			VF610_PAD_PTD23__ESDHC0_DAT4		0x31ef
+			VF610_PAD_PTD22__ESDHC0_DAT5		0x31ef
+			VF610_PAD_PTD21__ESDHC0_DAT6		0x31ef
+			VF610_PAD_PTD20__ESDHC0_DAT7		0x31ef
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			VF610_PAD_PTA24__ESDHC1_CLK		0x31ef
+			VF610_PAD_PTA25__ESDHC1_CMD		0x31ef
+			VF610_PAD_PTA26__ESDHC1_DAT0		0x31ef
+			VF610_PAD_PTA27__ESDHC1_DAT1		0x31ef
+			VF610_PAD_PTA28__ESDHC1_DATA2		0x31ef
+			VF610_PAD_PTA29__ESDHC1_DAT3		0x31ef
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			VF610_PAD_PTA6__RMII_CLKIN		0x30d1
+			VF610_PAD_PTC9__ENET_RMII1_MDC		0x30d2
+			VF610_PAD_PTC10__ENET_RMII1_MDIO	0x30d3
+			VF610_PAD_PTC11__ENET_RMII1_CRS		0x30d1
+			VF610_PAD_PTC12__ENET_RMII1_RXD1	0x30d1
+			VF610_PAD_PTC13__ENET_RMII1_RXD0	0x30d1
+			VF610_PAD_PTC14__ENET_RMII1_RXER	0x30d1
+			VF610_PAD_PTC15__ENET_RMII1_TXD1	0x30d2
+			VF610_PAD_PTC16__ENET_RMII1_TXD0	0x30d2
+			VF610_PAD_PTC17__ENET_RMII1_TXEN	0x30d2
+		>;
+	};
+
+	pinctrl_gpio_phy9: pinctrl-gpio-phy9 {
+		fsl,pins = <
+			VF610_PAD_PTB24__GPIO_94		0x219d
+		>;
+	};
+
+	pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
+		fsl,pins = <
+			VF610_PAD_PTE2__GPIO_107		0x31c2
+			VF610_PAD_PTB28__GPIO_98		0x219d
+		>;
+	};
+
+	pinctrl_i2c0: i2c0grp {
+		fsl,pins = <
+			VF610_PAD_PTB14__I2C0_SCL		0x37ff
+			VF610_PAD_PTB15__I2C0_SDA		0x37ff
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			VF610_PAD_PTB16__I2C1_SCL		0x37ff
+			VF610_PAD_PTB17__I2C1_SDA		0x37ff
+		>;
+	};
+
+	pinctrl_leds_debug: pinctrl-leds-debug {
+		fsl,pins = <
+			VF610_PAD_PTD3__GPIO_82			0x31c2
+		>;
+	};
+
+	pinctrl_uart0: uart0grp {
+		fsl,pins = <
+			VF610_PAD_PTB10__UART0_TX		0x21a2
+			VF610_PAD_PTB11__UART0_RX		0x21a1
+		>;
+	};
+};