@@ -227,6 +227,9 @@ dtb-$(CONFIG_ARCH_HIX5HD2) += \
dtb-$(CONFIG_ARCH_INTEGRATOR) += \
integratorap.dtb \
integratorcp.dtb
+dtb-$(CONFIG_ARCH_IXP4XX) += \
+ intel-ixp42x-linksys-nslu2.dtb \
+ intel-ixp43x-gateworks-gw2358-4.dtb
dtb-$(CONFIG_ARCH_KEYSTONE) += \
keystone-k2hk-evm.dtb \
keystone-k2l-evm.dtb \
new file mode 100644
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Linksys NSLU2
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Linksys NSLU2 (Network Storage Link for USB 2.0 Disk Drives)";
+ compatible = "linksys,nslu2", "intel,ixp42x";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 {
+ /* 32 MB SDRAM */
+ device_type = "memory";
+ reg = <0x00000000 0x2000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
+ stdout-path = "uart0:115200n8";
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-status {
+ label = "nslu2:red:status";
+ gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ led-ready {
+ label = "nslu2:green:ready";
+ gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ led-disk-1 {
+ label = "nslu2:green:disk-1";
+ gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ led-disk-2 {
+ label = "nslu2:green:disk-2";
+ gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ button-power {
+ wakeup-source;
+ linux,code = <KEY_POWER>;
+ label = "power";
+ gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ };
+ button-reset {
+ wakeup-source;
+ linux,code = <KEY_ESC>;
+ label = "reset";
+ gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-i2c {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rtc@6f {
+ compatible = "xicor,x1205";
+ reg = <0x6f>;
+ };
+ };
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+ timeout-ms = <5000>;
+ };
+
+ /* The first 16MB region on the expansion bus */
+ flash@50000000 {
+ compatible = "intel,ixp4xx-flash", "cfi-flash";
+ bank-width = <2>;
+ /*
+ * 8 MB of Flash in 0x20000 byte blocks
+ * mapped in at 0x50000000
+ */
+ reg = <0x50000000 0x800000>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partitions {
+ compatible = "redboot-fis";
+ /* Eraseblock at 0x7e0000 */
+ fis-index-block = <0x3f>;
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Intel XScale Network Processors
+ * in the IXP 42x series. This series has 32 interrupts.
+ */
+#include "intel-ixp4xx.dtsi"
+
+/ {
+ soc {
+ interrupt-controller@c8003000 {
+ compatible = "intel,ixp42x-interrupt";
+ };
+
+ /*
+ * This is the USB Device Mode (UDC) controller, which is used
+ * to present the IXP4xx as a device on a USB bus.
+ */
+ usb@c800b000 {
+ compatible = "intel,ixp4xx-udc";
+ reg = <0xc800b000 0x1000>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Gateworks IXP43x-based Cambria GW2358-4
+ */
+
+/dts-v1/;
+
+#include "intel-ixp43x.dtsi"
+
+/ {
+ model = "Gateworks Cambria GW2358-4";
+ compatible = "gateworks,gw2358-4", "intel,ixp43x";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 {
+ /* 128 MB SDRAM */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
+ stdout-path = "uart0:115200n8";
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-user {
+ label = "gw2385-4:greep:LED";
+ gpios = <&pld1 0 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+
+ gpio-i2c {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hwmon@28 {
+ compatible = "adi,ad7418";
+ reg = <0x28>;
+ };
+ rtc: ds1672@68 {
+ compatible = "dallas,ds1672";
+ reg = <0x68>;
+ };
+ eeprom@51 {
+ compatible = "atmel,24c08";
+ reg = <0x51>;
+ pagesize = <16>;
+ size = <1024>;
+ read-only;
+ };
+ pld0: pld@56 {
+ compatible = "gateworks,pld-gpio";
+ reg = <0x56>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ /* This PLD just handles the LED and user button */
+ pld1: pld@57 {
+ compatible = "gateworks,pld-gpio";
+ reg = <0x57>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
+
+ flash@50000000 {
+ compatible = "intel,ixp4xx-flash", "cfi-flash";
+ bank-width = <2>;
+ /*
+ * 32 MB of Flash in 0x20000 byte blocks
+ * mapped in at 0x50000000
+ */
+ reg = <0x50000000 0x2000000>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partitions {
+ compatible = "redboot-fis";
+ /* Eraseblock at 0x1fe0000 */
+ fis-index-block = <0xff>;
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Intel XScale Network Processors
+ * in the IXP 43x series. This series has 64 interrupts and adds a few more
+ * peripherals over the 42x series.
+ */
+#include "intel-ixp4xx.dtsi"
+
+/ {
+ soc {
+ interrupt-controller@c8003000 {
+ compatible = "intel,ixp43x-interrupt";
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Intel XScale Network Processors
+ * in the IXP45x and IXP46x series. This series has 64 interrupts and adds a
+ * few more peripherals over the 42x and 43x series so this extends the
+ * basic IXP4xx DTSI.
+ */
+#include "intel-ixp4xx.dtsi"
+
+/ {
+ soc {
+ interrupt-controller@c8003000 {
+ compatible = "intel,ixp43x-interrupt";
+ };
+
+ /*
+ * This is the USB Device Mode (UDC) controller, which is used
+ * to present the IXP4xx as a device on a USB bus.
+ */
+ usb@c800b000 {
+ compatible = "intel,ixp4xx-udc";
+ reg = <0xc800b000 0x1000>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ i2c@c8011000 {
+ compatible = "intel,ixp4xx-i2c";
+ reg = <0xc8011000 0x18>;
+ interrupts = <33 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Intel XScale Network Processors
+ * in the IXP 4xx series.
+ */
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ compatible = "simple-bus";
+ interrupt-parent = <&intcon>;
+
+ uart0: serial@c8000000 {
+ compatible = "intel,xscale-uart";
+ reg = <0xc8000000 0x1000>;
+ /*
+ * The reg-offset and reg-shift is a side effect
+ * of running the platform in big endian mode.
+ */
+ reg-offset = <3>;
+ reg-shift = <2>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <14745600>;
+ no-loopback-test;
+ };
+
+ gpio0: gpio@c8004000 {
+ compatible = "intel,ixp4xx-gpio";
+ reg = <0xc8004000 0x1000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ intcon: interrupt-controller@c8003000 {
+ /*
+ * Note: no compatible string. The subvariant of the
+ * chip needs to define what version it is. The
+ * location of the interrupt controller is fixed in
+ * memory across all variants.
+ */
+ reg = <0xc8003000 0x100>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ timer@c8005000 {
+ compatible = "intel,ixp4xx-timer";
+ reg = <0xc8005000 0x100>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+};
This adds a device tree for the IXP4xx-based Linksys NSLU2 and Gateworks GW2358-4 which is one platform in the Gateworks Cambria family. These will be the first IXP4xx device tree platforms. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- Since several of the DT bindings in these trees are not yet reviewed or merged upstream, this patch is RFC only, presented to make the review of the rest of the series readable. --- arch/arm/boot/dts/Makefile | 3 + .../boot/dts/intel-ixp42x-linksys-nslu2.dts | 111 ++++++++++++++++++ arch/arm/boot/dts/intel-ixp42x.dtsi | 25 ++++ .../dts/intel-ixp43x-gateworks-gw2358-4.dts | 96 +++++++++++++++ arch/arm/boot/dts/intel-ixp43x.dtsi | 15 +++ arch/arm/boot/dts/intel-ixp45x-ixp46x.dtsi | 34 ++++++ arch/arm/boot/dts/intel-ixp4xx.dtsi | 58 +++++++++ 7 files changed, 342 insertions(+) create mode 100644 arch/arm/boot/dts/intel-ixp42x-linksys-nslu2.dts create mode 100644 arch/arm/boot/dts/intel-ixp42x.dtsi create mode 100644 arch/arm/boot/dts/intel-ixp43x-gateworks-gw2358-4.dts create mode 100644 arch/arm/boot/dts/intel-ixp43x.dtsi create mode 100644 arch/arm/boot/dts/intel-ixp45x-ixp46x.dtsi create mode 100644 arch/arm/boot/dts/intel-ixp4xx.dtsi