@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
new file mode 100644
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+ compatible = "hardkernel,odroid-n2", "amlogic,g12b";
+ model = "Hardkernel ODROID-N2";
+
+ aliases {
+ serial0 = &uart_AO;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "n2:blue";
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ main_12v: regulator-main_12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vcc_1v8: regulator-vcc_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ /* FIXME: actually controlled by VDDCPU_B_EN */
+ };
+
+ hub_5v: regulator-hub_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "HUB_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+
+ gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_pwr_en: regulator-usb_pwr_en {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR_EN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&hub_5v>;
+
+ gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vddao_1v8: regulator-vddao_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&main_12v>;
+ regulator-always-on;
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&gpio {
+ /*
+ * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
+ * to be turned high in order to be detected by the USB Controller
+ * This signal should be handled by a USB specific power sequence
+ * in order to reset the Hub when USB bus is powered down.
+ */
+ usb-hub {
+ gpio-hog;
+ gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-hub-reset";
+ };
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb2_phy0 {
+ phy-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy1 {
+ phy-supply = <&vcc_5v>;
+};
new file mode 100644
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12a.dtsi"
+
+/ {
+ compatible = "amlogic,g12b";
+
+ cpus {
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+
+ core1 {
+ cpu = <&cpu1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&cpu100>;
+ };
+
+ core1 {
+ cpu = <&cpu101>;
+ };
+
+ core2 {
+ cpu = <&cpu102>;
+ };
+
+ core3 {
+ cpu = <&cpu103>;
+ };
+ };
+ };
+
+ /delete-node/ cpu@2;
+ /delete-node/ cpu@3;
+
+ cpu100: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu101: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x101>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu102: cpu@102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x102>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu103: cpu@103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73", "arm,armv8";
+ reg = <0x0 0x103>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+ };
+};
+
+&clkc {
+ compatible = "amlogic,g12b-clkc";
+};
This patch adds basic support for : - Amlogic G12B, which is very similar to G12A - The HardKernel Odroid-N2 based on the S922X SoC The Amlogic G12B SoC is very similar with the G12A SoC, sharing most of the features and architecture, but with these differences : - The first CPU cluster only has 2xCortex-A53 instead of 4 - G12B has a second cluster of 4xCortex-A73 - Both cluster can achieve 2GHz instead of 1,8GHz for G12A - CPU Clock architecture is difference, thus needing a different compatible to handle this slight difference - Supports a MIPI CSI input - Embeds a Mali-G52 instead of a Mali-G31, but integration is the same Actual support is done in the same way as for the GXM support, including the G12A dtsi and redefining the CPU clusters. Unlike GXM, the first cluster is different, thus needing to remove the last 2 cpu nodes of the first cluster. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 178 ++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 82 ++++++++ 3 files changed, 261 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi