| Message ID | 20190425082640.37982-1-andy.tang@nxp.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: dts: ls1028a: Add Thermal Monitor Unit node | expand |
On Thu, Apr 25, 2019 at 04:26:40PM +0800, Yuantian Tang wrote: > The Thermal Monitoring Unit (TMU) monitors and reports the > temperature from 2 remote temperature measurement sites > located on ls1028a chip. > Add TMU dts node to enable this feature. > > Signed-off-by: Yuantian Tang <andy.tang@nxp.com> I dont see anything wrong from a thermal standpoint. Acked-by: Eduardo Valentin <edubezval@gmail.com> Please get this via your arch tree maintainer to avoid merge conflicts. > --- > arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 114 ++++++++++++++++++++++++ > 1 files changed, 114 insertions(+), 0 deletions(-) > > diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi > index b045812..a25f5fc 100644 > --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi > +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi > @@ -29,6 +29,7 @@ > clocks = <&clockgen 1 0>; > next-level-cache = <&l2>; > cpu-idle-states = <&CPU_PH20>; > + #cooling-cells = <2>; > }; > > cpu1: cpu@1 { > @@ -39,6 +40,7 @@ > clocks = <&clockgen 1 0>; > next-level-cache = <&l2>; > cpu-idle-states = <&CPU_PH20>; > + #cooling-cells = <2>; > }; > > l2: l2-cache { > @@ -398,6 +400,118 @@ > status = "disabled"; > }; > > + tmu: tmu@1f00000 { > + compatible = "fsl,qoriq-tmu"; > + reg = <0x0 0x1f80000 0x0 0x10000>; > + interrupts = <0 23 0x4>; > + fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x70061>; > + fsl,tmu-calibration = <0x00000000 0x00000024 > + 0x00000001 0x0000002b > + 0x00000002 0x00000031 > + 0x00000003 0x00000038 > + 0x00000004 0x0000003f > + 0x00000005 0x00000045 > + 0x00000006 0x0000004c > + 0x00000007 0x00000053 > + 0x00000008 0x00000059 > + 0x00000009 0x00000060 > + 0x0000000a 0x00000066 > + 0x0000000b 0x0000006d > + > + 0x00010000 0x0000001c > + 0x00010001 0x00000024 > + 0x00010002 0x0000002c > + 0x00010003 0x00000035 > + 0x00010004 0x0000003d > + 0x00010005 0x00000045 > + 0x00010006 0x0000004d > + 0x00010007 0x00000045 > + 0x00010008 0x0000005e > + 0x00010009 0x00000066 > + 0x0001000a 0x0000006e > + > + 0x00020000 0x00000018 > + 0x00020001 0x00000022 > + 0x00020002 0x0000002d > + 0x00020003 0x00000038 > + 0x00020004 0x00000043 > + 0x00020005 0x0000004d > + 0x00020006 0x00000058 > + 0x00020007 0x00000063 > + 0x00020008 0x0000006e > + > + 0x00030000 0x00000010 > + 0x00030001 0x0000001c > + 0x00030002 0x00000029 > + 0x00030003 0x00000036 > + 0x00030004 0x00000042 > + 0x00030005 0x0000004f > + 0x00030006 0x0000005b > + 0x00030007 0x00000068>; > + little-endian; > + #thermal-sensor-cells = <1>; > + }; > + > + thermal-zones { > + core-cluster { > + polling-delay-passive = <1000>; > + polling-delay = <5000>; > + thermal-sensors = <&tmu 0>; > + > + trips { > + core_cluster_alert: core-cluster-alert { > + temperature = <85000>; > + hysteresis = <2000>; > + type = "passive"; > + }; > + > + core_cluster_crit: core-cluster-crit { > + temperature = <95000>; > + hysteresis = <2000>; > + type = "critical"; > + }; > + }; > + > + cooling-maps { > + map0 { > + trip = <&core_cluster_alert>; > + cooling-device = > + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > + }; > + }; > + }; > + > + ddr-controller { > + polling-delay-passive = <1000>; > + polling-delay = <5000>; > + thermal-sensors = <&tmu 1>; > + > + trips { > + ddr_controller_alert: ddr-controller-alert { > + temperature = <85000>; > + hysteresis = <2000>; > + type = "passive"; > + }; > + > + ddr_controller_crit: ddr-controller-crit { > + temperature = <95000>; > + hysteresis = <2000>; > + type = "critical"; > + }; > + }; > + > + cooling-maps { > + map0 { > + trip = <&ddr_controller_alert>; > + cooling-device = > + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > + }; > + }; > + }; > + }; > + > pcie@1f0000000 { /* Integrated Endpoint Root Complex */ > compatible = "pci-host-ecam-generic"; > reg = <0x01 0xf0000000 0x0 0x100000>;
> -----Original Message----- > From: Eduardo Valentin <edubezval@gmail.com> > Sent: 2019年5月29日 10:54 > To: Andy Tang <andy.tang@nxp.com> > Cc: shawnguo@kernel.org; Leo Li <leoyang.li@nxp.com>; > robh+dt@kernel.org; mark.rutland@arm.com; > linux-arm-kernel@lists.infradead.org; devicetree@vger.kernel.org; > linux-kernel@vger.kernel.org; linux-pm@vger.kernel.org; > daniel.lezcano@linaro.org; rui.zhang@intel.com > Subject: [EXT] Re: [PATCH] arm64: dts: ls1028a: Add Thermal Monitor Unit > node > > Caution: EXT Email > > On Thu, Apr 25, 2019 at 04:26:40PM +0800, Yuantian Tang wrote: > > The Thermal Monitoring Unit (TMU) monitors and reports the temperature > > from 2 remote temperature measurement sites located on ls1028a chip. > > Add TMU dts node to enable this feature. > > > > Signed-off-by: Yuantian Tang <andy.tang@nxp.com> > > I dont see anything wrong from a thermal standpoint. > > Acked-by: Eduardo Valentin <edubezval@gmail.com> > > Please get this via your arch tree maintainer to avoid merge conflicts. Thanks for your review. The only concern for arch tree maintainer is that "cooling-maps" is a required property. So I have to add cooling-maps for each zone. Since there are two thermal zones but only one cooling device, which is cpufreq, I have to use CPUFREQ as cooling device twice which may cause cooling decision conflict. The case will get worse when we have 7 thermal zones. This makes me think "maybe we need to change cooling-maps to an optional property". In this way, we can put the cooling devices to specific thermal zones and leave the zones without Cooling devices to do the default action which is reset or poweroff soc. What's your opinion about this? BR, Andy > > > --- > > arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 114 > > ++++++++++++++++++++++++ > > 1 files changed, 114 insertions(+), 0 deletions(-) > > > > diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi > > b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi > > index b045812..a25f5fc 100644 > > --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi > > +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi > > @@ -29,6 +29,7 @@ > > clocks = <&clockgen 1 0>; > > next-level-cache = <&l2>; > > cpu-idle-states = <&CPU_PH20>; > > + #cooling-cells = <2>; > > }; > > > > cpu1: cpu@1 { > > @@ -39,6 +40,7 @@ > > clocks = <&clockgen 1 0>; > > next-level-cache = <&l2>; > > cpu-idle-states = <&CPU_PH20>; > > + #cooling-cells = <2>; > > }; > > > > l2: l2-cache { > > @@ -398,6 +400,118 @@ > > status = "disabled"; > > }; > > > > + tmu: tmu@1f00000 { > > + compatible = "fsl,qoriq-tmu"; > > + reg = <0x0 0x1f80000 0x0 0x10000>; > > + interrupts = <0 23 0x4>; > > + fsl,tmu-range = <0xb0000 0xa0026 0x80048 > 0x70061>; > > + fsl,tmu-calibration = <0x00000000 0x00000024 > > + 0x00000001 > 0x0000002b > > + 0x00000002 > 0x00000031 > > + 0x00000003 > 0x00000038 > > + 0x00000004 > 0x0000003f > > + 0x00000005 > 0x00000045 > > + 0x00000006 > 0x0000004c > > + 0x00000007 > 0x00000053 > > + 0x00000008 > 0x00000059 > > + 0x00000009 > 0x00000060 > > + 0x0000000a > 0x00000066 > > + 0x0000000b > 0x0000006d > > + > > + 0x00010000 > 0x0000001c > > + 0x00010001 > 0x00000024 > > + 0x00010002 > 0x0000002c > > + 0x00010003 > 0x00000035 > > + 0x00010004 > 0x0000003d > > + 0x00010005 > 0x00000045 > > + 0x00010006 > 0x0000004d > > + 0x00010007 > 0x00000045 > > + 0x00010008 > 0x0000005e > > + 0x00010009 > 0x00000066 > > + 0x0001000a > 0x0000006e > > + > > + 0x00020000 > 0x00000018 > > + 0x00020001 > 0x00000022 > > + 0x00020002 > 0x0000002d > > + 0x00020003 > 0x00000038 > > + 0x00020004 > 0x00000043 > > + 0x00020005 > 0x0000004d > > + 0x00020006 > 0x00000058 > > + 0x00020007 > 0x00000063 > > + 0x00020008 > 0x0000006e > > + > > + 0x00030000 > 0x00000010 > > + 0x00030001 > 0x0000001c > > + 0x00030002 > 0x00000029 > > + 0x00030003 > 0x00000036 > > + 0x00030004 > 0x00000042 > > + 0x00030005 > 0x0000004f > > + 0x00030006 > 0x0000005b > > + 0x00030007 > 0x00000068>; > > + little-endian; > > + #thermal-sensor-cells = <1>; > > + }; > > + > > + thermal-zones { > > + core-cluster { > > + polling-delay-passive = <1000>; > > + polling-delay = <5000>; > > + thermal-sensors = <&tmu 0>; > > + > > + trips { > > + core_cluster_alert: > core-cluster-alert { > > + temperature = > <85000>; > > + hysteresis = > <2000>; > > + type = "passive"; > > + }; > > + > > + core_cluster_crit: > core-cluster-crit { > > + temperature = > <95000>; > > + hysteresis = > <2000>; > > + type = "critical"; > > + }; > > + }; > > + > > + cooling-maps { > > + map0 { > > + trip = > <&core_cluster_alert>; > > + cooling-device = > > + <&cpu0 > THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > > + <&cpu1 > THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > > + }; > > + }; > > + }; > > + > > + ddr-controller { > > + polling-delay-passive = <1000>; > > + polling-delay = <5000>; > > + thermal-sensors = <&tmu 1>; > > + > > + trips { > > + ddr_controller_alert: > ddr-controller-alert { > > + temperature = > <85000>; > > + hysteresis = > <2000>; > > + type = "passive"; > > + }; > > + > > + ddr_controller_crit: > ddr-controller-crit { > > + temperature = > <95000>; > > + hysteresis = > <2000>; > > + type = "critical"; > > + }; > > + }; > > + > > + cooling-maps { > > + map0 { > > + trip = > <&ddr_controller_alert>; > > + cooling-device = > > + <&cpu0 > THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > > + <&cpu1 > THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > > + }; > > + }; > > + }; > > + }; > > + > > pcie@1f0000000 { /* Integrated Endpoint Root Complex > */ > > compatible = "pci-host-ecam-generic"; > > reg = <0x01 0xf0000000 0x0 0x100000>;
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi index b045812..a25f5fc 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi @@ -29,6 +29,7 @@ clocks = <&clockgen 1 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PH20>; + #cooling-cells = <2>; }; cpu1: cpu@1 { @@ -39,6 +40,7 @@ clocks = <&clockgen 1 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PH20>; + #cooling-cells = <2>; }; l2: l2-cache { @@ -398,6 +400,118 @@ status = "disabled"; }; + tmu: tmu@1f00000 { + compatible = "fsl,qoriq-tmu"; + reg = <0x0 0x1f80000 0x0 0x10000>; + interrupts = <0 23 0x4>; + fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x70061>; + fsl,tmu-calibration = <0x00000000 0x00000024 + 0x00000001 0x0000002b + 0x00000002 0x00000031 + 0x00000003 0x00000038 + 0x00000004 0x0000003f + 0x00000005 0x00000045 + 0x00000006 0x0000004c + 0x00000007 0x00000053 + 0x00000008 0x00000059 + 0x00000009 0x00000060 + 0x0000000a 0x00000066 + 0x0000000b 0x0000006d + + 0x00010000 0x0000001c + 0x00010001 0x00000024 + 0x00010002 0x0000002c + 0x00010003 0x00000035 + 0x00010004 0x0000003d + 0x00010005 0x00000045 + 0x00010006 0x0000004d + 0x00010007 0x00000045 + 0x00010008 0x0000005e + 0x00010009 0x00000066 + 0x0001000a 0x0000006e + + 0x00020000 0x00000018 + 0x00020001 0x00000022 + 0x00020002 0x0000002d + 0x00020003 0x00000038 + 0x00020004 0x00000043 + 0x00020005 0x0000004d + 0x00020006 0x00000058 + 0x00020007 0x00000063 + 0x00020008 0x0000006e + + 0x00030000 0x00000010 + 0x00030001 0x0000001c + 0x00030002 0x00000029 + 0x00030003 0x00000036 + 0x00030004 0x00000042 + 0x00030005 0x0000004f + 0x00030006 0x0000005b + 0x00030007 0x00000068>; + little-endian; + #thermal-sensor-cells = <1>; + }; + + thermal-zones { + core-cluster { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 0>; + + trips { + core_cluster_alert: core-cluster-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + core_cluster_crit: core-cluster-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&core_cluster_alert>; + cooling-device = + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + ddr-controller { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 1>; + + trips { + ddr_controller_alert: ddr-controller-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + ddr_controller_crit: ddr-controller-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&ddr_controller_alert>; + cooling-device = + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + }; + pcie@1f0000000 { /* Integrated Endpoint Root Complex */ compatible = "pci-host-ecam-generic"; reg = <0x01 0xf0000000 0x0 0x100000>;
The Thermal Monitoring Unit (TMU) monitors and reports the temperature from 2 remote temperature measurement sites located on ls1028a chip. Add TMU dts node to enable this feature. Signed-off-by: Yuantian Tang <andy.tang@nxp.com> --- arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 114 ++++++++++++++++++++++++ 1 files changed, 114 insertions(+), 0 deletions(-)