| Message ID | 20190512082614.9045-4-tiny.windzz@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | add thermal driver for h6 | expand |
Hi, On Sun, May 12, 2019 at 04:26:14AM -0400, Yangtao Li wrote: > This patch adds binding document for allwinner h6 thermal controller. > > Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> > --- > .../bindings/thermal/sun50i-thermal.txt | 32 +++++++++++++++++++ > 1 file changed, 32 insertions(+) > create mode 100644 Documentation/devicetree/bindings/thermal/sun50i-thermal.txt We're starting to convert to YAML for binding descriptions that will allow to validate that all DT are properly using the binding. It would be great if you could use it as well. > diff --git a/Documentation/devicetree/bindings/thermal/sun50i-thermal.txt b/Documentation/devicetree/bindings/thermal/sun50i-thermal.txt > new file mode 100644 > index 000000000000..67eda7794262 > --- /dev/null > +++ b/Documentation/devicetree/bindings/thermal/sun50i-thermal.txt > @@ -0,0 +1,32 @@ > +Binding for Thermal Sensor of Allwinner SOC. > + > +This describes the device tree binding for the Allwinner thermal controller > +which measures the on-SoC temperatures. > + > +Required properties: > +- compatible: > + - "allwinner,sun50i-h6-ths" : For H6 > +- reg: Address range of the thermal controller > +- clocks, clock-names: Clocks needed for the thermal controller. > + The required clocks for h6 are: "bus". If there's a single clock, then we don't need clock-names > +- resets, reset-names: Reference to the reset controller controlling > + the thermal controller. Ditto. > +- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If > + unspecified default values shall be used. > +- nvmem-cell-names: Should be "calib" I thought you said that nvmem support was optional in the driver. Maybe we could make it optional in the DT too? Thanks! Maxime -- Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
On Sun, May 12, 2019 at 9:41 PM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > Hi, > > On Sun, May 12, 2019 at 04:26:14AM -0400, Yangtao Li wrote: > > This patch adds binding document for allwinner h6 thermal controller. > > > > Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> > > --- > > .../bindings/thermal/sun50i-thermal.txt | 32 +++++++++++++++++++ > > 1 file changed, 32 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/thermal/sun50i-thermal.txt > > We're starting to convert to YAML for binding descriptions that will > allow to validate that all DT are properly using the binding. It would > be great if you could use it as well. What have been changed to this now? > > > diff --git a/Documentation/devicetree/bindings/thermal/sun50i-thermal.txt b/Documentation/devicetree/bindings/thermal/sun50i-thermal.txt > > new file mode 100644 > > index 000000000000..67eda7794262 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/thermal/sun50i-thermal.txt > > @@ -0,0 +1,32 @@ > > +Binding for Thermal Sensor of Allwinner SOC. > > + > > +This describes the device tree binding for the Allwinner thermal controller > > +which measures the on-SoC temperatures. > > + > > +Required properties: > > +- compatible: > > + - "allwinner,sun50i-h6-ths" : For H6 > > +- reg: Address range of the thermal controller > > +- clocks, clock-names: Clocks needed for the thermal controller. > > + The required clocks for h6 are: "bus". > > If there's a single clock, then we don't need clock-names Yeah, but, IIRC, H3 have two clk. So I'd like to keep it. > > > +- resets, reset-names: Reference to the reset controller controlling > > + the thermal controller. > > Ditto. Done. Thx, Yangtao > > > +- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If > > + unspecified default values shall be used. > > +- nvmem-cell-names: Should be "calib" > > I thought you said that nvmem support was optional in the > driver. Maybe we could make it optional in the DT too? > > Thanks! > Maxime > > -- > Maxime Ripard, Bootlin > Embedded Linux and Kernel engineering > https://bootlin.com
On Fri, May 17, 2019 at 02:13:58AM +0800, Frank Lee wrote: > On Sun, May 12, 2019 at 9:41 PM Maxime Ripard <maxime.ripard@bootlin.com> wrote: > > > > Hi, > > > > On Sun, May 12, 2019 at 04:26:14AM -0400, Yangtao Li wrote: > > > This patch adds binding document for allwinner h6 thermal controller. > > > > > > Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> > > > --- > > > .../bindings/thermal/sun50i-thermal.txt | 32 +++++++++++++++++++ > > > 1 file changed, 32 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/thermal/sun50i-thermal.txt > > > > We're starting to convert to YAML for binding descriptions that will > > allow to validate that all DT are properly using the binding. It would > > be great if you could use it as well. > > What have been changed to this now? This needs a YAML file instead of the text file you introduced. Maxime -- Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
diff --git a/Documentation/devicetree/bindings/thermal/sun50i-thermal.txt b/Documentation/devicetree/bindings/thermal/sun50i-thermal.txt new file mode 100644 index 000000000000..67eda7794262 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/sun50i-thermal.txt @@ -0,0 +1,32 @@ +Binding for Thermal Sensor of Allwinner SOC. + +This describes the device tree binding for the Allwinner thermal controller +which measures the on-SoC temperatures. + +Required properties: +- compatible: + - "allwinner,sun50i-h6-ths" : For H6 +- reg: Address range of the thermal controller +- clocks, clock-names: Clocks needed for the thermal controller. + The required clocks for h6 are: "bus". +- resets, reset-names: Reference to the reset controller controlling + the thermal controller. +- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If + unspecified default values shall be used. +- nvmem-cell-names: Should be "calib" +- #thermal-sensor-cells : For H6 Should be 1. + See ./thermal.txt for a description. + +Example: + + ths: ths@1c25000 { + compatible = "allwinner,sun50i-h6-ths"; + reg = <0x05070400 0x100>; + clocks = <&ccu CLK_BUS_THS>; + clock-names = "bus"; + resets = <&ccu RST_BUS_THS>; + reset-names = "bus"; + nvmem-cells = <&tsen_calib>; + nvmem-cell-names = "calib"; + #thermal-sensor-cells = <1>; + };
This patch adds binding document for allwinner h6 thermal controller. Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> --- .../bindings/thermal/sun50i-thermal.txt | 32 +++++++++++++++++++ 1 file changed, 32 insertions(+) create mode 100644 Documentation/devicetree/bindings/thermal/sun50i-thermal.txt