@@ -7,3 +7,5 @@
#
dtb-$(CONFIG_ARCH_K3_AM6_SOC) += k3-am654-base-board.dtb
+
+dtb-$(CONFIG_ARCH_K3_J721E_SOC) += k3-j721e-common-proc-board.dtb
new file mode 100644
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "k3-j721e-som-p0.dtsi"
+
+/ {
+ chosen {
+ stdout-path = "serial2:115200n8";
+ bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+ };
+};
+
+&wkup_uart0 {
+ /* Wakeup UART is used by System firmware */
+ status = "disabled";
+};
+
+&main_uart3 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart5 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart6 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart7 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart8 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart9 {
+ /* UART not brought out */
+ status = "disabled";
+};
new file mode 100644
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "k3-j721e.dtsi"
+
+/ {
+ memory@80000000 {
+ device_type = "memory";
+ /* 4G RAM */
+ reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+ <0x00000008 0x80000000 0x00000000 0x80000000>;
+ };
+
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ secure_ddr: optee@9e800000 {
+ reg = <0x00 0x9e800000 0x00 0x01800000>;
+ alignment = <0x1000>;
+ no-map;
+ };
+ };
+};
Add Support for J721E Common Processor board support. The EVM architecture is as follows: +------------------------------------------------------+ | +-------------------------------------------+ | | | | | | | Add-on Card 1 Options | | | | | | | +-------------------------------------------+ | | | | | | +-------------------+ | | | | | | | SOM | | | +--------------+ | | | | | | | | | | | Add-on | +-------------------+ | | | Card 2 | | Power Supply | | Options | | | | | | | | | +--------------+ | <--- +------------------------------------------------------+ Common Processor Board Common Processor board is the baseboard that has most of the actual connectors, power supply etc. A SOM (System on Module) is plugged on to the common processor board and this contains the SoC, PMIC, DDR and basic high speed components necessary for functionality. Add-n card options add further functionality (such as additional Audio, Display, networking options). Note: A) The minimum configuration required to boot up the board is System On Module(SOM) + Common Processor Board. B) Since there is just a single SOM and Common Processor Board, we are maintaining common processor board as the base dts and SOM as the dtsi that we include. In the future as more SOM's appear, we should move common processor board as a dtsi and include configurations as dts. C) All daughter cards beyond the basic boards shall be maintained as overlays. Signed-off-by: Nishanth Menon <nm@ti.com> --- arch/arm64/boot/dts/ti/Makefile | 2 + .../dts/ti/k3-j721e-common-proc-board.dts | 50 +++++++++++++++++++ arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 29 +++++++++++ 3 files changed, 81 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi