| Message ID | 20190612205529.19834-2-martin.blumenstingl@googlemail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Ethernet PHY reset GPIO updates for Amlogic SoCs | expand |
On 12/06/2019 22:55, Martin Blumenstingl wrote: > The Odroid-N2 schematics show that the following pins are used for the > reset and interrupt lines: > - GPIOZ_14 is the PHY interrupt line > - GPIOZ_15 is the PHY reset line > > The GPIOZ_14 and GPIOZ_15 pins are special. The datasheet describes that > they are "3.3V input tolerant open drain (OD) output pins". This means > the GPIO controller can drive the output LOW to reset the PHY. To > release the reset it can only switch the pin to input mode. The output > cannot be driven HIGH for these pins. > This requires configuring the reset line as GPIO_OPEN_DRAIN because > otherwise the PHY will be stuck in "reset" state (because driving the > pin HIGH seems to result in the same signal as driving it LOW). > > The reset line works together with a pull-up resistor (R143 in the > Odroid-N2 schematics). The SoC can drive GPIOZ_14 LOW to assert the PHY > reset. However, since the SoC can't drive the pin HIGH (to release the > reset) we switch the mode to INPUT and let the pull-up resistor take > care of driving the reset line HIGH. > > Switch to GPIOZ_15 for the PHY reset line instead of using GPIOZ_14 > (which actually is the interrupt line). > Move from the "snps" specific resets to the MDIO framework's > reset-gpios because only the latter honors the GPIO flags. > Use the GPIO flags (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN) to match with > the pull-up resistor because this will: > - drive the output LOW to reset the PHY (= active low) > - switch the pin to INPUT mode so the pull-up will take the PHY out of > reset > > Fixes: 51d116557b2044 ("arm64: dts: meson-g12a-x96-max: Add Gigabit Ethernet Support") > Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> > --- > arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts | 7 ++++--- > 1 file changed, 4 insertions(+), 3 deletions(-) > > diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts > index 98bc56e650a0..de58d7817836 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts > +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts > @@ -176,6 +176,10 @@ > reg = <0>; > max-speed = <1000>; > eee-broken-1000t; > + > + reset-assert-us = <10000>; > + reset-deassert-us = <30000>; > + reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>; > }; > }; > > @@ -186,9 +190,6 @@ > phy-mode = "rgmii"; > phy-handle = <&external_phy>; > amlogic,tx-delay-ns = <2>; > - snps,reset-gpio = <&gpio GPIOZ_14 0>; > - snps,reset-delays-us = <0 10000 1000000>; > - snps,reset-active-low; > }; > > &pwm_ef { > Thanks for spotting this: Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts index 98bc56e650a0..de58d7817836 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts @@ -176,6 +176,10 @@ reg = <0>; max-speed = <1000>; eee-broken-1000t; + + reset-assert-us = <10000>; + reset-deassert-us = <30000>; + reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>; }; }; @@ -186,9 +190,6 @@ phy-mode = "rgmii"; phy-handle = <&external_phy>; amlogic,tx-delay-ns = <2>; - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; }; &pwm_ef {
The Odroid-N2 schematics show that the following pins are used for the reset and interrupt lines: - GPIOZ_14 is the PHY interrupt line - GPIOZ_15 is the PHY reset line The GPIOZ_14 and GPIOZ_15 pins are special. The datasheet describes that they are "3.3V input tolerant open drain (OD) output pins". This means the GPIO controller can drive the output LOW to reset the PHY. To release the reset it can only switch the pin to input mode. The output cannot be driven HIGH for these pins. This requires configuring the reset line as GPIO_OPEN_DRAIN because otherwise the PHY will be stuck in "reset" state (because driving the pin HIGH seems to result in the same signal as driving it LOW). The reset line works together with a pull-up resistor (R143 in the Odroid-N2 schematics). The SoC can drive GPIOZ_14 LOW to assert the PHY reset. However, since the SoC can't drive the pin HIGH (to release the reset) we switch the mode to INPUT and let the pull-up resistor take care of driving the reset line HIGH. Switch to GPIOZ_15 for the PHY reset line instead of using GPIOZ_14 (which actually is the interrupt line). Move from the "snps" specific resets to the MDIO framework's reset-gpios because only the latter honors the GPIO flags. Use the GPIO flags (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN) to match with the pull-up resistor because this will: - drive the output LOW to reset the PHY (= active low) - switch the pin to INPUT mode so the pull-up will take the PHY out of reset Fixes: 51d116557b2044 ("arm64: dts: meson-g12a-x96-max: Add Gigabit Ethernet Support") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> --- arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)