| Message ID | 20190726184045.14669-7-jernej.skrabec@siol.net (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | pwm: sun4i: Add support for Allwinner H6 | expand |
On Fri, Jul 26, 2019 at 08:40:45PM +0200, Jernej Skrabec wrote: > Allwinner H6 PWM is similar to that in A20 except that it has additional > bus clock and reset line. > > Note that first PWM channel is connected to output pin and second > channel is used internally, as a clock source to AC200 co-packaged chip. > This means that any combination of these two channels can be used and > thus it doesn't make sense to add pinctrl nodes at this point. > > Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> > --- > arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 10 ++++++++++ > 1 file changed, 10 insertions(+) > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi > index e8bed58e7246..c1abd805cfdc 100644 > --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi > @@ -229,6 +229,16 @@ > status = "disabled"; > }; > > + pwm: pwm@300a000 { > + compatible = "allwinner,sun50i-h6-pwm"; > + reg = <0x0300a000 0x400>; > + clocks = <&osc24M>, <&ccu CLK_BUS_PWM>; > + clock-names = "pwm", "bus"; We always have the bus clock first, so I'd really like to keep that. We also usually use mod for the second clock, and not the name of the device itself. Maxime -- Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi index e8bed58e7246..c1abd805cfdc 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi @@ -229,6 +229,16 @@ status = "disabled"; }; + pwm: pwm@300a000 { + compatible = "allwinner,sun50i-h6-pwm"; + reg = <0x0300a000 0x400>; + clocks = <&osc24M>, <&ccu CLK_BUS_PWM>; + clock-names = "pwm", "bus"; + resets = <&ccu RST_BUS_PWM>; + #pwm-cells = <3>; + status = "disabled"; + }; + pio: pinctrl@300b000 { compatible = "allwinner,sun50i-h6-pinctrl"; reg = <0x0300b000 0x400>;
Allwinner H6 PWM is similar to that in A20 except that it has additional bus clock and reset line. Note that first PWM channel is connected to output pin and second channel is used internally, as a clock source to AC200 co-packaged chip. This means that any combination of these two channels can be used and thus it doesn't make sense to add pinctrl nodes at this point. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> --- arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+)