@@ -336,7 +336,8 @@ dtb-$(CONFIG_MACH_MESON8) += \
dtb-$(CONFIG_ARCH_MMP) += \
pxa168-aspenite.dtb \
pxa910-dkb.dtb \
- mmp2-brownstone.dtb
+ mmp2-brownstone.dtb \
+ mmp2-olpc-xo-1-75.dtb
dtb-$(CONFIG_ARCH_MPS2) += \
mps2-an385.dtb \
mps2-an399.dtb
new file mode 100644
@@ -0,0 +1,244 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * OLPC XO 1.75 Laptop.
+ *
+ * Copyright (C) 2018,2019 Lubomir Rintel <lkundrak@v3.sk>
+ */
+
+/dts-v1/;
+#include "mmp2.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "OLPC XO-1.75";
+ compatible = "olpc,xo-1.75", "mrvl,mmp2";
+
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer@1fc00000 {
+ compatible = "simple-framebuffer";
+ reg = <0x1fc00000 (1200 * 900 * 2)>;
+ width = <1200>;
+ height = <900>;
+ stride = <(1200 * 2)>;
+ format = "r5g6b5";
+ clocks = <&soc_clocks MMP2_CLK_DISP0_LCDC>,
+ <&soc_clocks MMP2_CLK_DISP0>;
+ };
+ };
+
+ memory {
+ linux,usable-memory = <0x0 0x1f800000>;
+ available = <0xcf000 0x1ef31000 0x1000 0xbf000>;
+ reg = <0x0 0x20000000>;
+ device_type = "memory";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ lid {
+ label = "Lid";
+ gpios = <&gpio 129 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ wakeup-source;
+ };
+
+ tablet_mode {
+ label = "E-Book Mode";
+ gpios = <&gpio 128 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_TABLET_MODE>;
+ wakeup-source;
+ };
+
+ microphone_insert {
+ label = "Microphone Plug";
+ gpios = <&gpio 96 GPIO_ACTIVE_HIGH>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_MICROPHONE_INSERT>;
+ debounce-interval = <100>;
+ wakeup-source;
+ };
+
+ headphone_insert {
+ label = "Headphone Plug";
+ gpios = <&gpio 97 GPIO_ACTIVE_HIGH>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_HEADPHONE_INSERT>;
+ debounce-interval = <100>;
+ wakeup-source;
+ };
+ };
+
+ camera_i2c {
+ compatible = "i2c-gpio";
+ gpios = <&gpio 109 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>,
+ <&gpio 108 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-gpio,timeout-ms = <1000>;
+ status = "okay";
+
+ camera@21 {
+ compatible = "ovti,ov7670";
+ reg = <0x21>;
+ reset-gpios = <&gpio 102 GPIO_ACTIVE_LOW>;
+ powerdown-gpios = <&gpio 150 GPIO_ACTIVE_LOW>;
+ clocks = <&camera0>;
+ clock-names = "xclk";
+
+ port {
+ ov7670_0: endpoint {
+ hsync-active = <1>;
+ vsync-active = <1>;
+ remote-endpoint = <&camera0_0>;
+ };
+ };
+ };
+ };
+
+ battery {
+ compatible = "olpc,xo1.5-battery", "olpc,xo1-battery";
+ };
+
+ wlan_reg: fixedregulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio 34 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ wlan_pwrseq: pwrseq0 {
+ compatible = "mmc-pwrseq-sd8787";
+ powerdown-gpios = <&gpio 57 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio 58 GPIO_ACTIVE_HIGH>;
+ };
+
+ soc {
+ axi@d4200000 {
+ ap-sp@d4290000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "olpc,ap-sp";
+ interrupts = <40>;
+ reg = <0xd4290000 0x1000>;
+ data-gpios = <&gpio 72 GPIO_ACTIVE_HIGH>;
+ clk-gpios = <&gpio 71 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+ };
+ };
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&usb_phy0 {
+ status = "okay";
+};
+
+&usb_otg0 {
+ status = "okay";
+};
+
+&mmc1 {
+ clock-frequency = <50000000>;
+ no-1-8-v;
+ mrvl,clk-delay-cycles = <31>;
+ broken-cd;
+ status = "okay";
+};
+
+&mmc2 {
+ clock-frequency = <50000000>;
+ no-1-8-v;
+ bus-width = <4>;
+ non-removable;
+ broken-cd;
+ wakeup-source;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&wlan_pwrseq>;
+ vmmc-supply = <&wlan_reg>;
+ status = "okay";
+};
+
+&mmc3 {
+ clock-frequency = <50000000>;
+ no-1-8-v;
+ bus-width = <8>;
+ non-removable;
+ broken-cd;
+ mrvl,clk-delay-cycles = <31>;
+ status = "okay";
+};
+
+&twsi1 {
+ status = "okay";
+
+ audio-codec@1a {
+ compatible = "realtek,alc5631";
+ reg = <0x1a>;
+ status = "okay";
+ };
+};
+
+&twsi2 {
+ status = "okay";
+
+ rtc@68 {
+ compatible = "dallas,ds1338";
+ reg = <0x68>;
+ status = "okay";
+ };
+};
+
+&twsi6 {
+ status = "okay";
+
+ accelerometer@1d {
+ compatible = "st,lis331dlh", "st,lis3lv02d";
+ reg = <0x1d>;
+ status = "okay";
+ };
+};
+
+&ssp3 {
+ #address-cells = <0>;
+ spi-slave;
+ status = "okay";
+ ready-gpio = <&gpio 125 GPIO_ACTIVE_HIGH>;
+
+ slave {
+ compatible = "olpc,xo1.75-ec";
+ spi-cpha;
+ cmd-gpio = <&gpio 155 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&camera0 {
+ status = "okay";
+
+ port {
+ camera0_0: endpoint {
+ remote-endpoint = <&ov7670_0>;
+ };
+ };
+};
This is a fairly complete description of an OLPC XO 1.75 laptop. What's missing for now is the GPU, LCD controller, DCON, the panel and audio. The machine is booted with OpenFirmware and thus has a devicetree. However, older versions are unable to create a valid FDT and don't follow the Linux bindings. Having an device tree in the kernel tree makes it easier to use mainline kernels on such machines, test changes with CONFIG_ARM_APPENDED_DTB and give a good reference on what bindings are used on the machine without an access to one. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> --- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts | 244 ++++++++++++++++++++++++ 2 files changed, 246 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts