[v2] arm64: dts: ls1028a: Add Thermal Monitor Unit node

Commit Message

Andy Tang Aug. 6, 2019, 5:35 a.m. UTC

The Thermal Monitoring Unit (TMU) monitors and reports the
temperature from 2 remote temperature measurement sites
located on ls1028a chip.
Add TMU dts node to enable this feature.

Signed-off-by: Yuantian Tang <[e-mail]>
Acked-by: Eduardo Valentin <[e-mail]>
---
v2:
	- remove multiple sensors support

 .../arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 85 +++++++++++++++++++
 1 file changed, 85 insertions(+)

Comments

Shawn Guo Aug. 12, 2019, 2:11 p.m. UTC | #1

On Tue, Aug 06, 2019 at 01:35:07PM +0800, Yuantian Tang wrote:
> The Thermal Monitoring Unit (TMU) monitors and reports the
> temperature from 2 remote temperature measurement sites
> located on ls1028a chip.
> Add TMU dts node to enable this feature.
> 
> Signed-off-by: Yuantian Tang <[e-mail]>
> Acked-by: Eduardo Valentin <[e-mail]>

Applied, thanks.

Patch

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
index aef5b06a98d5..20d7e7db5dcb 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -29,6 +29,7 @@ 
 			clocks = <&clockgen 1 0>;
 			next-level-cache = <&l2>;
 			cpu-idle-states = <&CPU_PW20>;
+			#cooling-cells = <2>;
 		};
 
 		cpu1: cpu@1 {
@@ -39,6 +40,7 @@ 
 			clocks = <&clockgen 1 0>;
 			next-level-cache = <&l2>;
 			cpu-idle-states = <&CPU_PW20>;
+			#cooling-cells = <2>;
 		};
 
 		l2: l2-cache {
@@ -503,6 +505,89 @@ 
 			status = "disabled";
 		};
 
+		tmu: tmu@1f00000 {
+			compatible = "fsl,qoriq-tmu";
+			reg = <0x0 0x1f80000 0x0 0x10000>;
+			interrupts = <0 23 0x4>;
+			fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x70061>;
+			fsl,tmu-calibration = <0x00000000 0x00000024
+					       0x00000001 0x0000002b
+					       0x00000002 0x00000031
+					       0x00000003 0x00000038
+					       0x00000004 0x0000003f
+					       0x00000005 0x00000045
+					       0x00000006 0x0000004c
+					       0x00000007 0x00000053
+					       0x00000008 0x00000059
+					       0x00000009 0x00000060
+					       0x0000000a 0x00000066
+					       0x0000000b 0x0000006d
+
+					       0x00010000 0x0000001c
+					       0x00010001 0x00000024
+					       0x00010002 0x0000002c
+					       0x00010003 0x00000035
+					       0x00010004 0x0000003d
+					       0x00010005 0x00000045
+					       0x00010006 0x0000004d
+					       0x00010007 0x00000045
+					       0x00010008 0x0000005e
+					       0x00010009 0x00000066
+					       0x0001000a 0x0000006e
+
+					       0x00020000 0x00000018
+					       0x00020001 0x00000022
+					       0x00020002 0x0000002d
+					       0x00020003 0x00000038
+					       0x00020004 0x00000043
+					       0x00020005 0x0000004d
+					       0x00020006 0x00000058
+					       0x00020007 0x00000063
+					       0x00020008 0x0000006e
+
+					       0x00030000 0x00000010
+					       0x00030001 0x0000001c
+					       0x00030002 0x00000029
+					       0x00030003 0x00000036
+					       0x00030004 0x00000042
+					       0x00030005 0x0000004f
+					       0x00030006 0x0000005b
+					       0x00030007 0x00000068>;
+			little-endian;
+			#thermal-sensor-cells = <1>;
+		};
+
+		thermal-zones {
+			core-cluster {
+				polling-delay-passive = <1000>;
+				polling-delay = <5000>;
+				thermal-sensors = <&tmu 0>;
+
+				trips {
+					core_cluster_alert: core-cluster-alert {
+						temperature = <85000>;
+						hysteresis = <2000>;
+						type = "passive";
+					};
+
+					core_cluster_crit: core-cluster-crit {
+						temperature = <95000>;
+						hysteresis = <2000>;
+						type = "critical";
+					};
+				};
+
+				cooling-maps {
+					map0 {
+						trip = <&core_cluster_alert>;
+						cooling-device =
+							<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+					};
+				};
+			};
+		};
+
 		pcie@1f0000000 { /* Integrated Endpoint Root Complex */
 			compatible = "pci-host-ecam-generic";
 			reg = <0x01 0xf0000000 0x0 0x100000>;