@@ -9,3 +9,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb
new file mode 100644
@@ -0,0 +1,403 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9130-DB board.
+ */
+
+#include "cn9130.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Marvell Armada CN9130-DB";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ gpio1 = &cp0_gpio1;
+ gpio2 = &cp0_gpio2;
+ i2c0 = &cp0_i2c0;
+ ethernet0 = &cp0_eth0;
+ ethernet1 = &cp0_eth1;
+ ethernet2 = &cp0_eth2;
+ spi1 = &cp0_spi0;
+ spi2 = &cp0_spi1;
+ };
+
+ memory@00000000 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ ap0_reg_sd_vccq: ap0_sd_vccq@0 {
+ compatible = "regulator-gpio";
+ regulator-name = "ap0_sd_vccq";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&expander0 8 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1 3300000 0x0>;
+ };
+
+ cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0-xhci0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp0_usb3_0_phy0: cp0_usb3_phy@0 {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <&cp0_reg_usb3_vbus0>;
+ };
+
+ cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0-xhci1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp0_usb3_0_phy1: cp0_usb3_phy@1 {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <&cp0_reg_usb3_vbus1>;
+ };
+
+ cp0_reg_sd_vccq: cp0_sd_vccq@0 {
+ compatible = "regulator-gpio";
+ regulator-name = "cp0_sd_vccq";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&expander0 15 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ };
+
+ cp0_reg_sd_vcc: cp0_sd_vcc@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0_sd_vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&expander0 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ cp0_sfp_eth0: sfp-eth@0 {
+ compatible = "sff,sfp";
+ i2c-bus = <&cp0_sfpp0_i2c>;
+ los-gpio = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>;
+ /*
+ * SFP cages are unconnected on early PCBs because of an the I2C
+ * lanes not being connected. Prevent the port for being
+ * unusable by disabling the SFP node.
+ */
+ status = "disabled";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+/* on-board eMMC - U9 */
+&ap_sdhci0 {
+ pinctrl-names = "default";
+ bus-width = <8>;
+ vqmmc-supply = <&ap0_reg_sd_vccq>;
+ status = "okay";
+};
+
+&cp0_crypto {
+ status = "disabled";
+};
+
+&cp0_ethernet {
+ status = "okay";
+};
+
+/* SLM-1521-V2, CON9 */
+&cp0_eth0 {
+ status = "disabled";
+ phy-mode = "10gbase-kr";
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp0_comphy4 0>;
+ managed = "in-band-status";
+ sfp = <&cp0_sfp_eth0>;
+};
+
+/* CON56 */
+&cp0_eth1 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+};
+
+/* CON57 */
+&cp0_eth2 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+};
+
+&cp0_gpio1 {
+ status = "okay";
+};
+
+&cp0_gpio2 {
+ status = "okay";
+};
+
+&cp0_i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c0_pins>;
+ clock-frequency = <100000>;
+
+ /* U36 */
+ expander0: pca953x@21 {
+ compatible = "nxp,pca9555";
+ pinctrl-names = "default";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x21>;
+ status = "okay";
+ };
+
+ /* U42 */
+ eeprom0: eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ pagesize = <0x20>;
+ };
+
+ /* U38 */
+ eeprom1: eeprom@57 {
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ pagesize = <0x20>;
+ };
+};
+
+&cp0_i2c1 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ /* SLM-1521-V2 - U3 */
+ i2c-mux@72 { /* verify address - depends on dpr */
+ compatible = "nxp,pca9544";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72>;
+ cp0_sfpp0_i2c: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* U12 */
+ cp0_module_expander1: pca9555@21 {
+ compatible = "nxp,pca9555";
+ pinctrl-names = "default";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x21>;
+ };
+
+ };
+ };
+};
+
+&cp0_mdio {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+/* U54 */
+&cp0_nand_controller {
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_pins &nand_rb>;
+
+ nand@0 {
+ reg = <0>;
+ label = "main-storage";
+ nand-rb = <0>;
+ nand-ecc-mode = "hw";
+ nand-on-flash-bbt;
+ nand-ecc-strength = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0 0x200000>;
+ };
+ partition@200000 {
+ label = "Linux";
+ reg = <0x200000 0xd00000>;
+ };
+ partition@1000000 {
+ label = "Filesystem";
+ reg = <0x1000000 0x3f000000>;
+ };
+ };
+ };
+};
+
+/* SLM-1521-V2, CON6 */
+&cp0_pcie0 {
+ status = "okay";
+ num-lanes = <4>;
+ num-viewport = <8>;
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp0_comphy0 0
+ &cp0_comphy1 0
+ &cp0_comphy2 0
+ &cp0_comphy3 0>;
+};
+
+&cp0_sata0 {
+ status = "okay";
+
+ /* SLM-1521-V2, CON2 */
+ sata-port@1 {
+ status = "okay";
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp0_comphy5 1>;
+ };
+};
+
+/* CON 28 */
+&cp0_sdhci0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_sdhci_pins
+ &cp0_sdhci_cd_pins>;
+ bus-width = <4>;
+ cd-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ vqmmc-supply = <&cp0_reg_sd_vccq>;
+ vmmc-supply = <&cp0_reg_sd_vcc>;
+};
+
+/* U55 */
+&cp0_spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_spi0_pins>;
+ reg = <0x700680 0x50>;
+
+ spi-flash@0 {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ /* On-board MUX does not allow higher frequencies */
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "U-Boot-0";
+ reg = <0x0 0x200000>;
+ };
+
+ partition@400000 {
+ label = "Filesystem-0";
+ reg = <0x200000 0xe00000>;
+ };
+ };
+ };
+};
+
+&cp0_syscon0 {
+ cp0_pinctrl: pinctrl {
+ compatible = "marvell,cp115-standalone-pinctrl";
+
+ cp0_i2c0_pins: cp0-i2c-pins-0 {
+ marvell,pins = "mpp37", "mpp38";
+ marvell,function = "i2c0";
+ };
+ cp0_i2c1_pins: cp0-i2c-pins-1 {
+ marvell,pins = "mpp35", "mpp36";
+ marvell,function = "i2c1";
+ };
+ cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 {
+ marvell,pins = "mpp0", "mpp1", "mpp2",
+ "mpp3", "mpp4", "mpp5",
+ "mpp6", "mpp7", "mpp8",
+ "mpp9", "mpp10", "mpp11";
+ marvell,function = "ge0";
+ };
+ cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 {
+ marvell,pins = "mpp44", "mpp45", "mpp46",
+ "mpp47", "mpp48", "mpp49",
+ "mpp50", "mpp51", "mpp52",
+ "mpp53", "mpp54", "mpp55";
+ marvell,function = "ge1";
+ };
+ cp0_sdhci_cd_pins: cp0-sdhci-cd-pins-0 {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+ cp0_sdhci_pins: cp0-sdhi-pins-0 {
+ marvell,pins = "mpp56", "mpp57", "mpp58",
+ "mpp59", "mpp60", "mpp61";
+ marvell,function = "sdio";
+ };
+ cp0_spi0_pins: cp0-spi-pins-0 {
+ marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+ marvell,function = "spi1";
+ };
+ nand_pins: nand-pins {
+ marvell,pins = "mpp15", "mpp16", "mpp17", "mpp18",
+ "mpp19", "mpp20", "mpp21", "mpp22",
+ "mpp23", "mpp24", "mpp25", "mpp26",
+ "mpp27";
+ marvell,function = "dev";
+ };
+ nand_rb: nand-rb {
+ marvell,pins = "mpp13";
+ marvell,function = "nf";
+ };
+ };
+};
+
+&cp0_usb3_0 {
+ status = "okay";
+ usb-phy = <&cp0_usb3_0_phy0>;
+ phy-names = "usb";
+};
+
+&cp0_usb3_1 {
+ status = "okay";
+ usb-phy = <&cp0_usb3_0_phy1>;
+ phy-names = "usb";
+};