@@ -1,13 +1,13 @@
# SPDX-License-Identifier: GPL-2.0-only
menuconfig ARCH_MMP
- bool "Marvell PXA168/910/MMP2"
+ bool "Marvell PXA168/910/MMP2/MMP3"
depends on ARCH_MULTI_V5 || ARCH_MULTI_V7
select GPIO_PXA
select GPIOLIB
select PINCTRL
select PLAT_PXA
help
- Support for Marvell's PXA168/PXA910(MMP) and MMP2 processor line.
+ Support for Marvell's PXA168/PXA910(MMP), MMP2, and MMP3 processor lines.
if ARCH_MMP
@@ -129,6 +129,24 @@ config MACH_MMP2_DT
Include support for Marvell MMP2 based platforms using
the device tree.
+config MACH_MMP3_DT
+ bool "Support MMP3 (ARMv7) platforms"
+ depends on ARCH_MULTI_V7
+ select ARM_GIC
+ select HAVE_ARM_SCU if SMP
+ select HAVE_ARM_TWD if SMP
+ select CACHE_L2X0
+ select PINCTRL
+ select PINCTRL_SINGLE
+ select ARCH_HAS_RESET_CONTROLLER
+ select CPU_PJ4B
+ select PM_GENERIC_DOMAINS if PM
+ select PM_GENERIC_DOMAINS_OF if PM && OF
+ help
+ Say 'Y' here if you want to include support for platforms
+ with Marvell MMP3 processor, also known as PXA2128 or
+ Armada 620.
+
endmenu
config CPU_PXA168
@@ -34,5 +34,6 @@ obj-$(CONFIG_MACH_FLINT) += flint.o
obj-$(CONFIG_MACH_MARVELL_JASPER) += jasper.o
obj-$(CONFIG_MACH_MMP_DT) += mmp-dt.o
obj-$(CONFIG_MACH_MMP2_DT) += mmp2-dt.o
+obj-$(CONFIG_MACH_MMP3_DT) += mmp3.o
obj-$(CONFIG_MACH_TETON_BGA) += teton_bga.o
obj-$(CONFIG_MACH_GPLUGD) += gplugd.o
@@ -18,6 +18,8 @@
* MMP2 Z0 0x560f5811 0x00F00410
* MMP2 Z1 0x560f5811 0x00E00410
* MMP2 A0 0x560f5811 0x00A0A610
+ * MMP3 A0 0x562f5842 0x00A02128
+ * MMP3 B0 0x562f5842 0x00B02128
*/
extern unsigned int mmp_chip_id;
@@ -55,4 +57,29 @@ static inline int cpu_is_mmp2(void)
#define cpu_is_mmp2() (0)
#endif
+#ifdef CONFIG_MACH_MMP3_DT
+static inline int cpu_is_mmp3(void)
+{
+ return (((read_cpuid_id() >> 8) & 0xff) == 0x58) &&
+ ((mmp_chip_id & 0xffff) == 0x2128);
+}
+
+static inline int cpu_is_mmp3_a0(void)
+{
+ return (cpu_is_mmp3() &&
+ ((mmp_chip_id & 0x00ff0000) == 0x00a00000));
+}
+
+static inline int cpu_is_mmp3_b0(void)
+{
+ return (cpu_is_mmp3() &&
+ ((mmp_chip_id & 0x00ff0000) == 0x00b00000));
+}
+
+#else
+#define cpu_is_mmp3() (0)
+#define cpu_is_mmp3_a0() (0)
+#define cpu_is_mmp3_b0() (0)
+#endif
+
#endif /* __ASM_MACH_CPUTYPE_H */
new file mode 100644
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Marvell MMP3 aka PXA2128 aka 88AP2128 support
+ *
+ * Copyright (C) 2019 Lubomir Rintel <lkundrak@v3.sk>
+ */
+
+#include <linux/io.h>
+#include <linux/irqchip.h>
+#include <linux/of_platform.h>
+#include <linux/clk-provider.h>
+#include <asm/mach/arch.h>
+#include <asm/hardware/cache-l2x0.h>
+
+#include "common.h"
+
+static const char *const mmp3_dt_board_compat[] __initconst = {
+ "marvell,mmp3",
+ NULL,
+};
+
+DT_MACHINE_START(MMP2_DT, "Marvell MMP3")
+ .map_io = mmp2_map_io,
+ .dt_compat = mmp3_dt_board_compat,
+ .l2c_aux_val = 1 << L310_AUX_CTRL_FWA_SHIFT |
+ L310_AUX_CTRL_DATA_PREFETCH |
+ L310_AUX_CTRL_INSTR_PREFETCH,
+ .l2c_aux_mask = 0xc20fffff,
+MACHINE_END
@@ -155,7 +155,8 @@ static void __init timer_config(void)
__raw_writel(0x0, mmp_timer_base + TMR_CER); /* disable */
- ccr &= (cpu_is_mmp2()) ? (TMR_CCR_CS_0(0) | TMR_CCR_CS_1(0)) :
+ ccr &= (cpu_is_mmp2() || cpu_is_mmp3()) ?
+ (TMR_CCR_CS_0(0) | TMR_CCR_CS_1(0)) :
(TMR_CCR_CS_0(3) | TMR_CCR_CS_1(3));
__raw_writel(ccr, mmp_timer_base + TMR_CCR);
@@ -9,6 +9,7 @@ obj-$(CONFIG_RESET_CONTROLLER) += reset.o
obj-$(CONFIG_MACH_MMP_DT) += clk-of-pxa168.o clk-of-pxa910.o
obj-$(CONFIG_MACH_MMP2_DT) += clk-of-mmp2.o
+obj-$(CONFIG_MACH_MMP3_DT) += clk-of-mmp2.o
obj-$(CONFIG_CPU_PXA168) += clk-pxa168.o
obj-$(CONFIG_CPU_PXA910) += clk-pxa910.o
Similar to MMP2, which this patch is based on. Known differencies from MMP2 are: * Two PJ4B cores instead of one PJ4 * Tauros 3 L2 cache controller instead of Tauros 2 * A GIC interrupt controller optionally used instead of the MMP one * A TWD local timer * Different USB2 PHY * A USB3 SS controller * More interrupt muxes Hard to tell what else is different, because documentation is not available. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> --- arch/arm/mach-mmp/Kconfig | 22 ++++++++++++++++++++-- arch/arm/mach-mmp/Makefile | 1 + arch/arm/mach-mmp/cputype.h | 27 +++++++++++++++++++++++++++ arch/arm/mach-mmp/mmp3.c | 29 +++++++++++++++++++++++++++++ arch/arm/mach-mmp/time.c | 3 ++- drivers/clk/mmp/Makefile | 1 + 6 files changed, 80 insertions(+), 3 deletions(-) create mode 100644 arch/arm/mach-mmp/mmp3.c