[V9,2/3] Documentation: admin-guide: perf: add i.MX8 ddr pmu user doc

Commit Message

Joakim Zhang Aug. 28, 2019, 12:07 p.m. UTC

Add i.MX8 ddr pmu user doc.

Signed-off-by: Joakim Zhang <[e-mail]>

---
ChangeLog:
V1 -> V4:
	* new add in V4.
V4 -> V5:
	* no change.
V5 -> V6:
	* change the event name
V6 -> V7:
	* no change.
V7 -> V8:
	* improve the doc, add more details.
V8 -> V9:
	* improve the doc.
---
 Documentation/admin-guide/perf/imx-ddr.rst | 52 ++++++++++++++++++++++
 1 file changed, 52 insertions(+)
 create mode 100644 Documentation/admin-guide/perf/imx-ddr.rst

Patch

diff --git a/Documentation/admin-guide/perf/imx-ddr.rst b/Documentation/admin-guide/perf/imx-ddr.rst
new file mode 100644
index 000000000000..517a205abad6
--- /dev/null
+++ b/Documentation/admin-guide/perf/imx-ddr.rst
@@ -0,0 +1,52 @@ 
+=====================================================
+Freescale i.MX8 DDR Performance Monitoring Unit (PMU)
+=====================================================
+
+There are no performance counters inside the DRAM controller, so performance
+signals are brought out to the edge of the controller where a set of 4 x 32 bit
+counters is implemented. This is controlled by the CSV modes programed in counter
+control register which causes a large number of PERF signals to be generated.
+
+Selection of the value for each counter is done via the config registers. There
+is one register for each counter. Counter 0 is special in that it always counts
+“time” and when expired causes a lock on itself and the other counters and an
+interrupt is raised. If any other counter overflows, it continues counting, and
+no interrupt is raised.
+
+The "format" directory describes format of the config (event ID) and config1
+(AXI filtering) fields of the perf_event_attr structure, see /sys/bus/event_source/
+devices/imx8_ddr0/format/. The "events" directory describes the events types
+hardware supported that can be used with perf tool, see /sys/bus/event_source/
+devices/imx8_ddr0/events/.
+  e.g.::
+        perf stat -a -e imx8_ddr0/cycles/ cmd
+        perf stat -a -e imx8_ddr0/read/,imx8_ddr0/write/ cmd
+
+AXI filtering is only used by CSV modes 0x41 (axid-read) and 0x42 (axid-write)
+to count reading or writing matches filter setting. Filter setting is various
+from different DRAM controller implementations, which is distinguished by quirks
+in the driver.
+
+* With DDR_CAP_AXI_ID_FILTER quirk.
+  Filter is defined with two configuration parts:
+  --AXI_ID defines AxID matching value.
+  --AXI_MASKING defines which bits of AxID are meaningful for the matching.
+        0：corresponding bit is masked.
+        1: corresponding bit is not masked, i.e. used to do the matching.
+
+  AXI_ID and AXI_MASKING are mapped on DPCR1 register in performance counter.
+  When non-masked bits are matching corresponding AXI_ID bits then counter is
+  incremented. Perf counter is incremented if
+          AxID && AXI_MASKING == AXI_ID && AXI_MASKING
+
+  This filter doesn't support filter different AXI ID for axid-read and axid-write
+  event at the same time as this filter is shared between counters.
+  e.g.::
+        perf stat -a -e imx8_ddr0/axid-read,axi_mask=0xMMMM,axi_id=0xDDDD/ cmd
+        perf stat -a -e imx8_ddr0/axid-write,axi_mask=0xMMMM,axi_id=0xDDDD/ cmd
+
+  NOTE: axi_mask is inverted in userspace(i.e. set bits are bits to mask), and
+  it will be reverted in driver automatically. so that the user can just specify
+  axi_id to monitor a specific id, rather than having to specify axi_mask.
+  e.g.::
+        perf stat -a -e imx8_ddr0/axid-read,axi_id=0x12/ cmd, which will monitor ARID=0x12