diff mbox series

[v5,7/7] arm64: dts: allwinner: a64: enable ANX6345 bridge on Teres-I

Message ID 20191104110616.750F368C7B@verein.lst.de (mailing list archive)
State New, archived
Headers show
Series Add anx6345 DP/eDP bridge for Olimex Teres-I | expand

Commit Message

Torsten Duwe Oct. 29, 2019, 12:16 p.m. UTC 
Teres-I has an anx6345 bridge connected to the RGB666 LCD output, and
the I2C controlling signals are connected to I2C0 bus.

Enable it in the device tree, and enable the display engine, video mixer
and tcon0 as well.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Torsten Duwe <duwe@suse.de>
---
 .../boot/dts/allwinner/sun50i-a64-teres-i.dts      | 45 ++++++++++++++++++++--
 1 file changed, 41 insertions(+), 4 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
index 1069e7012c9c..970415106dcf 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
@@ -100,18 +100,41 @@ 
 	status = "okay";
 };
 
+&de {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
 
 
-/* The ANX6345 eDP-bridge is on i2c0. There is no linux (mainline)
- * driver for this chip at the moment, the bootloader initializes it.
- * However it can be accessed with the i2c-dev driver from user space.
- */
 &i2c0 {
 	clock-frequency = <100000>;
 	status = "okay";
+
+	anx6345: anx6345@38 {
+		compatible = "analogix,anx6345";
+		reg = <0x38>;
+		reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */
+		dvdd25-supply = <&reg_dldo2>;
+		dvdd12-supply = <&reg_dldo3>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				anx6345_in: endpoint {
+					remote-endpoint = <&tcon0_out_anx6345>;
+				};
+			};
+		};
+	};
+};
+
+&mixer0 {
+	status = "okay";
 };
 
 &mmc0 {
@@ -319,6 +342,20 @@ 
 	status = "okay";
 };
 
+&tcon0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcd_rgb666_pins>;
+
+	status = "okay";
+};
+
+&tcon0_out {
+	tcon0_out_anx6345: endpoint@0 {
+		reg = <0>;
+		remote-endpoint = <&anx6345_in>;
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pb_pins>;