@@ -67,6 +67,40 @@ main_usbss1_pins_default: main_usbss1_pins_default {
J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
>;
};
+
+ main_i2c1_exp4_pins_default: main-i2c1-exp4-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x230, PIN_INPUT, 7) /* (U2) ECAP0_IN_APWM_OUT.GPIO1_11 */
+ >;
+ };
+
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
+ J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
+ >;
+ };
+
+ main_i2c1_pins_default: main-i2c1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
+ J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
+ >;
+ };
+
+ main_i2c3_pins_default: main-i2c3-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
+ J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
+ >;
+ };
+
+ main_i2c6_pins_default: main-i2c6-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x1d0, PIN_INPUT_PULLUP, 2) /* (AA3) SPI0_D1.I2C6_SCL */
+ J721E_IOPAD(0x1e4, PIN_INPUT_PULLUP, 2) /* (Y2) SPI1_D1.I2C6_SDA */
+ >;
+ };
};
&wkup_pmx0 {
@@ -75,6 +109,19 @@ sw11_button_pins_default: sw11_button_pins_default {
J721E_WKUP_IOPAD(0xcc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
>;
};
+
+ mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x34, PIN_OUTPUT, 0) /* (F22) MCU_OSPI1_CLK */
+ J721E_WKUP_IOPAD(0x50, PIN_OUTPUT, 0) /* (C22) MCU_OSPI1_CSn0 */
+ J721E_WKUP_IOPAD(0x40, PIN_INPUT, 0) /* (D22) MCU_OSPI1_D0 */
+ J721E_WKUP_IOPAD(0x44, PIN_INPUT, 0) /* (G22) MCU_OSPI1_D1 */
+ J721E_WKUP_IOPAD(0x48, PIN_INPUT, 0) /* (D23) MCU_OSPI1_D2 */
+ J721E_WKUP_IOPAD(0x4c, PIN_INPUT, 0) /* (C23) MCU_OSPI1_D3 */
+ J721E_WKUP_IOPAD(0x3c, PIN_INPUT, 0) /* (B23) MCU_OSPI1_DQS */
+ J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */
+ >;
+ };
};
&wkup_uart0 {
@@ -279,3 +326,94 @@ &usb1 {
dr_mode = "host";
maximum-speed = "high-speed";
};
+
+&ospi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
+
+ flash@0{
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <40000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&tscadc0 {
+ adc {
+ ti,adc-channels = <0 1 2 3 4 5 6 7>;
+ };
+};
+
+&tscadc1 {
+ adc {
+ ti,adc-channels = <0 1 2 3 4 5 6 7>;
+ };
+};
+
+&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
+ exp1: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ exp2: gpio@22 {
+ compatible = "ti,tca6424";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&main_i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c1_pins_default>;
+ clock-frequency = <400000>;
+
+ exp4: gpio@20 {
+ compatible = "ti,tca6408";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&main_i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c3_pins_default>;
+ clock-frequency = <400000>;
+
+ exp3: gpio@20 {
+ compatible = "ti,tca6408";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&main_i2c6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c6_pins_default>;
+ clock-frequency = <400000>;
+
+ exp5: gpio@20 {
+ compatible = "ti,tca6408";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
@@ -596,4 +596,103 @@ usb1: usb@6400000 {
dr_mode = "otg";
};
};
+
+ main_i2c0: i2c@2000000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x0 0x2000000 0x0 0x100>;
+ interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 187 0>;
+ power-domains = <&k3_pds 187 TI_SCI_PD_SHARED>;
+ };
+
+ main_i2c1: i2c@2010000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x0 0x2010000 0x0 0x100>;
+ interrupts = <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 188 0>;
+ power-domains = <&k3_pds 188 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ main_i2c2: i2c@2020000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x0 0x2020000 0x0 0x100>;
+ interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 189 0>;
+ power-domains = <&k3_pds 189 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ main_i2c3: i2c@2030000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x0 0x2030000 0x0 0x100>;
+ interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 190 0>;
+ power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ main_i2c4: i2c@2040000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x0 0x2040000 0x0 0x100>;
+ interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 191 0>;
+ power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ main_i2c5: i2c@2050000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x0 0x2050000 0x0 0x100>;
+ interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 192 0>;
+ power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ main_i2c6: i2c@2060000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x0 0x2060000 0x0 0x100>;
+ interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 193 0>;
+ power-domains = <&k3_pds 193 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ ufs_wrapper: ufs-wrapper@4e80000 {
+ compatible = "ti,j721e-ufs";
+ reg = <0x0 0x4e80000 0x0 0x100>;
+ power-domains = <&k3_pds 277 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 277 1>;
+ assigned-clocks = <&k3_clks 277 1>;
+ assigned-clock-parents = <&k3_clks 277 4>;
+ ranges;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ ufs@4e84000 {
+ compatible = "cdns,ufshc-m31-16nm", "jedec,ufs-2.0";
+ reg = <0x0 0x4e84000 0x0 0x10000>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ freq-table-hz = <250000000 250000000>, <19200000 19200000>, <19200000 19200000>;
+ clocks = <&k3_clks 277 0>, <&k3_clks 277 1>, <&k3_clks 277 1>;
+ clock-names = "core_clk", "phy_clk", "ref_clk";
+ dma-coherent;
+ };
+ };
};
@@ -121,4 +121,108 @@ wkup_gpio1: gpio@42100000 {
clocks = <&k3_clks 114 0>;
clock-names = "gpio";
};
+
+ mcu_i2c0: i2c@40b00000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x0 0x40b00000 0x0 0x100>;
+ interrupts = <GIC_SPI 852 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 194 0>;
+ power-domains = <&k3_pds 194 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ mcu_i2c1: i2c@40b10000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x0 0x40b10000 0x0 0x100>;
+ interrupts = <GIC_SPI 853 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 195 0>;
+ power-domains = <&k3_pds 195 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ wkup_i2c0: i2c@42120000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x0 0x42120000 0x0 0x100>;
+ interrupts = <GIC_SPI 896 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 197 0>;
+ power-domains = <&k3_pds 197 TI_SCI_PD_SHARED>;
+ };
+
+ fss: fss@47000000 {
+ compatible = "simple-bus";
+ reg = <0x0 0x47000000 0x0 0x100>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ospi0: spi@47040000 {
+ compatible = "ti,am654-ospi";
+ reg = <0x0 0x47040000 0x0 0x100>,
+ <0x5 0x00000000 0x1 0x0000000>;
+ interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
+ cdns,fifo-depth = <256>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x0>;
+ clocks = <&k3_clks 103 0>;
+ assigned-clocks = <&k3_clks 103 0>;
+ assigned-clock-parents = <&k3_clks 103 2>;
+ assigned-clock-rates = <166666666>;
+ power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ospi1: spi@47050000 {
+ compatible = "ti,am654-ospi";
+ reg = <0x0 0x47050000 0x0 0x100>,
+ <0x7 0x00000000 0x1 0x00000000>;
+ interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>;
+ cdns,fifo-depth = <256>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x0>;
+ clocks = <&k3_clks 104 0>;
+ power-domains = <&k3_pds 104 TI_SCI_PD_EXCLUSIVE>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ tscadc0: tscadc@40200000 {
+ compatible = "ti,am3359-tscadc";
+ reg = <0x0 0x40200000 0x0 0x1000>;
+ interrupts = <GIC_SPI 860 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 0 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 0 1>;
+ assigned-clocks = <&k3_clks 0 3>;
+ assigned-clock-rates = <60000000>;
+ clock-names = "adc_tsc_fck";
+
+ adc {
+ #io-channel-cells = <1>;
+ compatible = "ti,am3359-adc";
+ };
+ };
+
+ tscadc1: tscadc@40210000 {
+ compatible = "ti,am3359-tscadc";
+ reg = <0x0 0x40210000 0x0 0x1000>;
+ interrupts = <GIC_SPI 861 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 1 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 1 1>;
+ assigned-clocks = <&k3_clks 1 3>;
+ assigned-clock-rates = <60000000>;
+ clock-names = "adc_tsc_fck";
+
+ adc {
+ #io-channel-cells = <1>;
+ compatible = "ti,am3359-adc";
+ };
+ };
};
@@ -27,3 +27,48 @@ secure_ddr: optee@9e800000 {
};
};
};
+
+&wkup_pmx0 {
+ wkup_i2c0_pins_default: wkup_i2c0_pins_default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
+ J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
+ >;
+ };
+
+ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
+ J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0) /* MCU_OSPI0_DQS */
+ J721E_WKUP_IOPAD(0x000c, PIN_INPUT, 0) /* MCU_OSPI0_D0 */
+ J721E_WKUP_IOPAD(0x0010, PIN_INPUT, 0) /* MCU_OSPI0_D1 */
+ J721E_WKUP_IOPAD(0x0014, PIN_INPUT, 0) /* MCU_OSPI0_D2 */
+ J721E_WKUP_IOPAD(0x0018, PIN_INPUT, 0) /* MCU_OSPI0_D3 */
+ J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_OSPI0_D4 */
+ J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_OSPI0_D5 */
+ J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_OSPI0_D6 */
+ J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_OSPI0_D7 */
+ J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */
+ >;
+ };
+};
+
+&ospi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+ flash@0{
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <40000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
Enable I2Cs, ADCs, OSPIs and UFS peripherals present on J721e. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> --- .../dts/ti/k3-j721e-common-proc-board.dts | 138 ++++++++++++++++++ arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 99 +++++++++++++ .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 104 +++++++++++++ arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 45 ++++++ 4 files changed, 386 insertions(+)