| Message ID | 20191211144638.24676-2-m.szyprowski@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v2,1/4] ARM: dts: exynos: Correct USB3503 GPIOs polarity | expand |
On Wed, Dec 11, 2019 at 03:46:35PM +0100, Marek Szyprowski wrote: > Current USB3503 driver ignores GPIO polarity and always operates as if the > GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing > USB3503 chip applications to match the chip specification and common > convention for naming the pins. The only pin, which has to be ACTIVE_LOW > is the reset pin. The remaining are ACTIVE_HIGH. This change allows later > to fix the USB3503 driver to properly use generic GPIO bindings and read > polarity from DT. > Thanks, applied (for v5.6). Best regards, Krzysztof
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi index ea55f377d17c..9c39e82e4ecb 100644 --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi @@ -267,7 +267,7 @@ intn-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>; connect-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; initial-mode = <1>; }; diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts index d6c85efdb465..3eddf5dbcf7b 100644 --- a/arch/arm/boot/dts/exynos5250-arndale.dts +++ b/arch/arm/boot/dts/exynos5250-arndale.dts @@ -154,7 +154,7 @@ compatible = "smsc,usb3503a"; reset-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; - connect-gpios = <&gpd1 7 GPIO_ACTIVE_LOW>; + connect-gpios = <&gpd1 7 GPIO_ACTIVE_HIGH>; }; }; diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts index e0db251e253f..4f9297ae0763 100644 --- a/arch/arm/boot/dts/exynos5410-odroidxu.dts +++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts @@ -170,7 +170,7 @@ intn-gpios = <&gpx0 7 GPIO_ACTIVE_HIGH>; connect-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpx1 4 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpx1 4 GPIO_ACTIVE_LOW>; initial-mode = <1>; clock-names = "refclk";
Current USB3503 driver ignores GPIO polarity and always operates as if the GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing USB3503 chip applications to match the chip specification and common convention for naming the pins. The only pin, which has to be ACTIVE_LOW is the reset pin. The remaining are ACTIVE_HIGH. This change allows later to fix the USB3503 driver to properly use generic GPIO bindings and read polarity from DT. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> --- arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 2 +- arch/arm/boot/dts/exynos5250-arndale.dts | 2 +- arch/arm/boot/dts/exynos5410-odroidxu.dts | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-)