| Message ID | 20200223172916.843379-4-megous@megous.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add support for Pine64 PinePhone Linux Smartphone | expand |
Hi, On Sun, Feb 23, 2020 at 06:29:16PM +0100, Ondrej Jirman wrote: > At them moment PinePhone comes in two slightly incompatible variants: > > - 1.0: Early Developer Batch > - 1.1: Braveheart Batch > > There will be at least one more incompatible variant in the very near > future, so let's start by sharing the dtsi among multiple variants, > right away, even though the HW description doesn't yet include the > different bits. > > This is a basic DT that includes only features that are already > supported by mainline drivers. What are those incompatibilities? It's not really obvious from your patch. > Co-developed-by: Samuel Holland <samuel@sholland.org> > Signed-off-by: Samuel Holland <samuel@sholland.org> > Co-developed-by: Martijn Braam <martijn@brixit.nl> > Signed-off-by: Martijn Braam <martijn@brixit.nl> > Co-developed-by: Luca Weiss <luca@z3ntu.xyz> > Signed-off-by: Luca Weiss <luca@z3ntu.xyz> > Signed-off-by: Bhushan Shah <bshah@kde.org> > Signed-off-by: Icenowy Zheng <icenowy@aosc.io> > Signed-off-by: Ondrej Jirman <megous@megous.com> > --- > arch/arm64/boot/dts/allwinner/Makefile | 2 + > .../allwinner/sun50i-a64-pinephone-1.0.dts | 11 + > .../allwinner/sun50i-a64-pinephone-1.1.dts | 11 + > .../dts/allwinner/sun50i-a64-pinephone.dtsi | 385 ++++++++++++++++++ > 4 files changed, 409 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile > index cf4f78617c3f3..79ca263672c38 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -9,6 +9,8 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.0.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.1.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts > new file mode 100644 > index 0000000000000..0c42272106afa > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts > @@ -0,0 +1,11 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> Given the list of authors, surely you're not the sole copyright owner here? > +/dts-v1/; > + > +#include "sun50i-a64-pinephone.dtsi" > + > +/ { > + model = "Pine64 PinePhone Developer Batch (1.0)"; > + compatible = "pine64,pinephone-1.0", "allwinner,sun50i-a64"; > +}; > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts > new file mode 100644 > index 0000000000000..06a775c41664b > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts > @@ -0,0 +1,11 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> > + > +/dts-v1/; > + > +#include "sun50i-a64-pinephone.dtsi" > + > +/ { > + model = "Pine64 PinePhone Braveheart (1.1)"; > + compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64"; > +}; > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi > new file mode 100644 > index 0000000000000..d0cf21d82c9e9 > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi > @@ -0,0 +1,385 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +// Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz> > +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> > + > +#include "sun50i-a64.dtsi" > +#include "sun50i-a64-cpu-opp.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pwm/pwm.h> > + > +/ { > + aliases { > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + blue { > + function = LED_FUNCTION_INDICATOR; > + function-enumerator = <1>; > + color = <LED_COLOR_ID_BLUE>; > + gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */ > + }; > + > + green { > + function = LED_FUNCTION_INDICATOR; > + function-enumerator = <2>; > + color = <LED_COLOR_ID_GREEN>; > + gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */ > + }; > + > + red { > + function = LED_FUNCTION_INDICATOR; > + function-enumerator = <3>; > + color = <LED_COLOR_ID_RED>; > + gpios = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */ > + }; > + }; LEDs should be named using the $color:$board:$usage pattern > + > + speaker_amp: audio-amplifier { > + compatible = "simple-audio-amplifier"; > + enable-gpios = <&pio 2 7 GPIO_ACTIVE_HIGH>; /* PC7 */ > + sound-name-prefix = "Speaker Amp"; > + }; > + > + vibrator { > + compatible = "gpio-vibrator"; > + enable-gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */ > + vcc-supply = <®_dcdc1>; > + }; > +}; > + > +&codec { > + status = "okay"; > +}; > + > +&codec_analog { > + cpvdd-supply = <®_eldo1>; > + status = "okay"; > +}; > + > +&cpu0 { > + cpu-supply = <®_dcdc2>; > +}; > + > +&cpu1 { > + cpu-supply = <®_dcdc2>; > +}; > + > +&cpu2 { > + cpu-supply = <®_dcdc2>; > +}; > + > +&cpu3 { > + cpu-supply = <®_dcdc2>; > +}; > + > +&dai { > + status = "okay"; > +}; > + > +&ehci0 { > + status = "okay"; > +}; > + > +&ehci1 { > + status = "okay"; > +}; > + > +&i2c1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins>; That's the default > + status = "okay"; > + > + /* Magnetometer */ > + lis3mdl@1e { > + compatible = "st,lis3mdl-magn"; > + reg = <0x1e>; > + vdd-supply = <®_dldo1>; > + vddio-supply = <®_dldo1>; > + }; > + > + /* Accelerometer/gyroscope */ > + mpu6050@68 { > + compatible = "invensense,mpu6050"; > + reg = <0x68>; > + interrupt-parent = <&pio>; > + interrupts = <7 5 IRQ_TYPE_EDGE_RISING>; /* PH5 */ > + vdd-supply = <®_dldo1>; > + vddio-supply = <®_dldo1>; > + }; > +}; > + > +/* Connected to pogo pins */ > +&i2c2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c2_pins>; That's the default as well > + status = "okay"; > +}; And I'm not sure what the pogo pins are? > + > +&lradc { > + vref-supply = <®_aldo3>; > + status = "okay"; > + > + button-200 { > + label = "Volume Up"; > + linux,code = <KEY_VOLUMEUP>; > + channel = <0>; > + voltage = <200000>; > + }; > + > + button-400 { > + label = "Volume Down"; > + linux,code = <KEY_VOLUMEDOWN>; > + channel = <0>; > + voltage = <400000>; > + }; > +}; > + > +&mmc0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc0_pins>; That's the default > + vmmc-supply = <®_dcdc1>; > + vqmmc-supply = <®_dcdc1>; > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > + disable-wp; > + bus-width = <4>; > + status = "okay"; > +}; > + > +&mmc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc2_pins>; Ditto > + vmmc-supply = <®_dcdc1>; > + vqmmc-supply = <®_dcdc1>; > + bus-width = <8>; > + non-removable; > + cap-mmc-hw-reset; > + status = "okay"; > +}; > + > +&ohci0 { > + status = "okay"; > +}; > + > +&ohci1 { > + status = "okay"; > +}; > + > +&pio { > + vcc-pb-supply = <®_dcdc1>; > + vcc-pc-supply = <®_dcdc1>; > + vcc-pd-supply = <®_dcdc1>; > + vcc-pe-supply = <®_aldo1>; > + vcc-pf-supply = <®_dcdc1>; > + vcc-pg-supply = <®_dldo4>; > + vcc-ph-supply = <®_dcdc1>; > +}; > + > +&r_pio { > + /* > + * FIXME: We can't add that supply for now since it would > + * create a circular dependency between pinctrl, the regulator > + * and the RSB Bus. > + * > + * vcc-pl-supply = <®_aldo2>; > + */ > +}; > + > +&r_rsb { > + status = "okay"; > + > + axp803: pmic@3a3 { > + compatible = "x-powers,axp803"; > + reg = <0x3a3>; > + interrupt-parent = <&r_intc>; > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; > + }; > +}; > + > +#include "axp803.dtsi" > + > +&ac_power_supply { > + status = "okay"; > +}; > + > +&battery_power_supply { > + status = "okay"; > +}; > + > +®_aldo1 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "dovdd-csi"; > +}; > + > +®_aldo2 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc-pl"; > +}; > + > +®_aldo3 { > + regulator-always-on; > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-pll-avcc"; > +}; > + > +®_dcdc1 { > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-3v3"; > +}; > + > +®_dcdc2 { > + regulator-always-on; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1300000>; > + regulator-name = "vdd-cpux"; > +}; > + > +/* DCDC3 is polyphased with DCDC2 */ > + > +®_dcdc5 { > + regulator-always-on; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-name = "vcc-dram"; > +}; > + > +®_dcdc6 { > + regulator-always-on; > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + regulator-name = "vdd-sys"; > +}; > + > +®_dldo1 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-dsi-sensor"; > +}; > + > +®_dldo2 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc-mipi-io"; > +}; > + > +®_dldo3 { > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-name = "avdd-csi"; > +}; > + > +®_dldo4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-wifi-io"; > +}; > + > +®_eldo1 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc-lpddr"; > +}; > + > +®_eldo3 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "dvdd-1v8-csi"; > +}; > + > +®_fldo1 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-name = "vcc-1v2-hsic"; > +}; > + > +®_fldo2 { > + regulator-always-on; > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + regulator-name = "vdd-cpus"; > +}; > + > +®_ldo_io0 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-lcd-ctp-stk"; > + status = "okay"; > +}; > + > +®_ldo_io1 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc-1v8-typec"; > + status = "okay"; > +}; > + > +®_rtc_ldo { > + regulator-name = "vcc-rtc"; > +}; > + > +&sound { > + status = "okay"; > + simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>; > + simple-audio-card,widgets = "Microphone", "Headset Microphone", > + "Microphone", "Internal Microphone", > + "Headphone", "Headphone Jack", > + "Speaker", "Internal Earpiece", > + "Speaker", "Internal Speaker"; > + simple-audio-card,routing = > + "Headphone Jack", "HP", > + "Internal Earpiece", "EARPIECE", > + "Internal Speaker", "Speaker Amp OUTL", > + "Internal Speaker", "Speaker Amp OUTR", > + "Speaker Amp INL", "LINEOUT", > + "Speaker Amp INR", "LINEOUT", > + "Left DAC", "AIF1 Slot 0 Left", > + "Right DAC", "AIF1 Slot 0 Right", > + "AIF1 Slot 0 Left ADC", "Left ADC", > + "AIF1 Slot 0 Right ADC", "Right ADC", > + "Internal Microphone", "MBIAS", > + "MIC1", "Internal Microphone", > + "Headset Microphone", "HBIAS", > + "MIC2", "Headset Microphone"; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_pb_pins>; > + status = "okay"; > +}; > + > +/* Connected to the modem */ > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart3_pins>; That's the default too, and I guess you'd need hardware flow control here? > + status = "okay"; > +}; > + > +&usb_otg { > + dr_mode = "peripheral"; > + status = "okay"; > +}; > + > +&usb_power_supply { > + status = "okay"; > +}; > + > +&usbphy { > + status = "okay"; > +}; > -- > 2.25.1 > Looks good otherwise, thanks! Maxime
Hello Maxime, On Mon, Feb 24, 2020 at 12:00:27PM +0100, Maxime Ripard wrote: > Hi, > > On Sun, Feb 23, 2020 at 06:29:16PM +0100, Ondrej Jirman wrote: > > At them moment PinePhone comes in two slightly incompatible variants: > > > > - 1.0: Early Developer Batch > > - 1.1: Braveheart Batch > > > > There will be at least one more incompatible variant in the very near > > future, so let's start by sharing the dtsi among multiple variants, > > right away, even though the HW description doesn't yet include the > > different bits. > > > > This is a basic DT that includes only features that are already > > supported by mainline drivers. > > What are those incompatibilities? It's not really obvious from your > patch. The changes are listed here: https://wiki.pine64.org/index.php/PinePhone_v1.1_-_Braveheart#Changes_from_1.0 Substantial ones are: 2. Swap PC3 to FLASH_EN and PD24 to FLASH_TRIGOUT, where previously they were reversed 5. Set the EG25G's PWRKEY on by default (see resistor R1526) 6. Add R630 resistor location, populate with 0K by default. Allows adjusting to different battery thermistors in case this is not possible in software. The incompatiblilities between 1.1 and 1.2 will be more extensive: https://wiki.pine64.org/index.php/PinePhone/Power_Management#Suggested_GPIO_Hardware_Changes > > Co-developed-by: Samuel Holland <samuel@sholland.org> > > Signed-off-by: Samuel Holland <samuel@sholland.org> > > Co-developed-by: Martijn Braam <martijn@brixit.nl> > > Signed-off-by: Martijn Braam <martijn@brixit.nl> > > Co-developed-by: Luca Weiss <luca@z3ntu.xyz> > > Signed-off-by: Luca Weiss <luca@z3ntu.xyz> > > Signed-off-by: Bhushan Shah <bshah@kde.org> > > Signed-off-by: Icenowy Zheng <icenowy@aosc.io> > > Signed-off-by: Ondrej Jirman <megous@megous.com> > > --- > > arch/arm64/boot/dts/allwinner/Makefile | 2 + > > .../allwinner/sun50i-a64-pinephone-1.0.dts | 11 + > > .../allwinner/sun50i-a64-pinephone-1.1.dts | 11 + > > .../dts/allwinner/sun50i-a64-pinephone.dtsi | 385 ++++++++++++++++++ > > 4 files changed, 409 insertions(+) > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi > > > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile > > index cf4f78617c3f3..79ca263672c38 100644 > > --- a/arch/arm64/boot/dts/allwinner/Makefile > > +++ b/arch/arm64/boot/dts/allwinner/Makefile > > @@ -9,6 +9,8 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb > > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.0.dtb > > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.1.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts > > new file mode 100644 > > index 0000000000000..0c42272106afa > > --- /dev/null > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts > > @@ -0,0 +1,11 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> > > Given the list of authors, surely you're not the sole copyright owner > here? Yes, I made this and the 1.1 dts file by myself. It's not really a meaningful contribution, since at the moment it's basically empty. I suppose to have a license, the file requires some author. Collaborative work is mostly in the dtsi. > > +/dts-v1/; > > + > > +#include "sun50i-a64-pinephone.dtsi" > > + > > +/ { > > + model = "Pine64 PinePhone Developer Batch (1.0)"; > > + compatible = "pine64,pinephone-1.0", "allwinner,sun50i-a64"; > > +}; > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts > > new file mode 100644 > > index 0000000000000..06a775c41664b > > --- /dev/null > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts > > @@ -0,0 +1,11 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> > > + > > +/dts-v1/; > > + > > +#include "sun50i-a64-pinephone.dtsi" > > + > > +/ { > > + model = "Pine64 PinePhone Braveheart (1.1)"; > > + compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64"; > > +}; > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi > > new file mode 100644 > > index 0000000000000..d0cf21d82c9e9 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi > > @@ -0,0 +1,385 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +// Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz> > > +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> For the record. Originally I took this file from: https://gitlab.com/pine64-org/linux/commits/pine64-kernel-5.4.y https://gitlab.com/pine64-org/linux/-/blob/pine64-kernel-5.4.y/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dts about a month ago, and kept working on it in my trees for 5.5 and 5.6: https://megous.com/git/linux/log/?h=pp-5.5 https://megous.com/git/linux/log/?h=pp-5.6 Adding support for using multiple cameras, bugfixing, and integrating work from others, and now doing the legwork to strip the more complete DTS and make it into a mainlainable state, so that collaboration can continue in the mainline tree. AFAIK, at this point (after stripdown), most of the work comes from Icenowy. With some people contributing "smaller" things. I say "smaller" in quotes, since I know that there can be a weekend of debugging behind changing a 2-3 lines, and don't want to minimize anyone's contribution. IANAL and I don't know what's entirely apropriate to do here. I've disucssed this briefly on the IRC with involved people (that are also CCed in this series), and there was a suggestion to adding a bunch of Cob/SoB tags, based on some even older DTS file for dontbeevil (developer kit for PinePhone), that the Icenowy's file was based on. So I did. The more copyright holders the better, I guess. :) So if CCed people want to be added here, and made the contribution to the present file, please state so for the record again here on the mailing list, and I'll add you to the header, or anywhere you wish. > > +#include "sun50i-a64.dtsi" > > +#include "sun50i-a64-cpu-opp.dtsi" > > + > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/input/input.h> > > +#include <dt-bindings/leds/common.h> > > +#include <dt-bindings/pwm/pwm.h> > > + > > +/ { > > + aliases { > > + serial0 = &uart0; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:115200n8"; > > + }; > > + > > + leds { > > + compatible = "gpio-leds"; > > + > > + blue { > > + function = LED_FUNCTION_INDICATOR; > > + function-enumerator = <1>; > > + color = <LED_COLOR_ID_BLUE>; > > + gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */ > > + }; > > + > > + green { > > + function = LED_FUNCTION_INDICATOR; > > + function-enumerator = <2>; > > + color = <LED_COLOR_ID_GREEN>; > > + gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */ > > + }; > > + > > + red { > > + function = LED_FUNCTION_INDICATOR; > > + function-enumerator = <3>; > > + color = <LED_COLOR_ID_RED>; > > + gpios = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */ > > + }; > > + }; > > LEDs should be named using the $color:$board:$usage pattern Do you mean using a label? It seems label is deprecated, and bindings should start using function/function-enumerator/color properties now: https://elixir.bootlin.com/linux/v5.6-rc2/source/Documentation/devicetree/bindings/leds/common.yaml#L57 It doesn't look like the new bindings are used much, yet. I've found: https://elixir.bootlin.com/linux/v5.6-rc2/source/arch/arm64/boot/dts/amlogic/meson-gxbb-kii-pro.dts and https://elixir.bootlin.com/linux/v5.6-rc2/source/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi#L96 On PinePhone these are indicator leds with no pre-defined meaning, for use by the apps to indicate things like a new SMS, or missed call, or whatever people desire. > > + > > + speaker_amp: audio-amplifier { > > + compatible = "simple-audio-amplifier"; > > + enable-gpios = <&pio 2 7 GPIO_ACTIVE_HIGH>; /* PC7 */ > > + sound-name-prefix = "Speaker Amp"; > > + }; > > + > > + vibrator { > > + compatible = "gpio-vibrator"; > > + enable-gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */ > > + vcc-supply = <®_dcdc1>; > > + }; > > +}; > > + > > +&codec { > > + status = "okay"; > > +}; > > + > > +&codec_analog { > > + cpvdd-supply = <®_eldo1>; > > + status = "okay"; > > +}; > > + > > +&cpu0 { > > + cpu-supply = <®_dcdc2>; > > +}; > > + > > +&cpu1 { > > + cpu-supply = <®_dcdc2>; > > +}; > > + > > +&cpu2 { > > + cpu-supply = <®_dcdc2>; > > +}; > > + > > +&cpu3 { > > + cpu-supply = <®_dcdc2>; > > +}; > > + > > +&dai { > > + status = "okay"; > > +}; > > + > > +&ehci0 { > > + status = "okay"; > > +}; > > + > > +&ehci1 { > > + status = "okay"; > > +}; > > + > > +&i2c1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c1_pins>; > > That's the default Ok. > > + status = "okay"; > > + > > + /* Magnetometer */ > > + lis3mdl@1e { > > + compatible = "st,lis3mdl-magn"; > > + reg = <0x1e>; > > + vdd-supply = <®_dldo1>; > > + vddio-supply = <®_dldo1>; > > + }; > > + > > + /* Accelerometer/gyroscope */ > > + mpu6050@68 { > > + compatible = "invensense,mpu6050"; > > + reg = <0x68>; > > + interrupt-parent = <&pio>; > > + interrupts = <7 5 IRQ_TYPE_EDGE_RISING>; /* PH5 */ > > + vdd-supply = <®_dldo1>; > > + vddio-supply = <®_dldo1>; > > + }; > > +}; > > + > > +/* Connected to pogo pins */ > > +&i2c2 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&i2c2_pins>; > > That's the default as well Actually it is not. There's not i2c2_pins at all in the mainline yet. > > + status = "okay"; > > +}; > > And I'm not sure what the pogo pins are? It's a common name for spring-loaded pin headers that can be used to connect the phone to auxiliary devices. 6 pins are visible on this image near the top: https://wiki.pine64.org/index.php/File:PinePhone_switches.jpeg > > + > > +&lradc { > > + vref-supply = <®_aldo3>; > > + status = "okay"; > > + > > + button-200 { > > + label = "Volume Up"; > > + linux,code = <KEY_VOLUMEUP>; > > + channel = <0>; > > + voltage = <200000>; > > + }; > > + > > + button-400 { > > + label = "Volume Down"; > > + linux,code = <KEY_VOLUMEDOWN>; > > + channel = <0>; > > + voltage = <400000>; > > + }; > > +}; > > + > > +&mmc0 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&mmc0_pins>; > > That's the default Ok. > > + vmmc-supply = <®_dcdc1>; > > + vqmmc-supply = <®_dcdc1>; > > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > > + disable-wp; > > + bus-width = <4>; > > + status = "okay"; > > +}; > > + > > +&mmc2 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&mmc2_pins>; > > Ditto Will remove. > > + vmmc-supply = <®_dcdc1>; > > + vqmmc-supply = <®_dcdc1>; > > + bus-width = <8>; > > + non-removable; > > + cap-mmc-hw-reset; > > + status = "okay"; > > +}; > > + > > +&ohci0 { > > + status = "okay"; > > +}; > > + > > +&ohci1 { > > + status = "okay"; > > +}; > > + > > +&pio { > > + vcc-pb-supply = <®_dcdc1>; > > + vcc-pc-supply = <®_dcdc1>; > > + vcc-pd-supply = <®_dcdc1>; > > + vcc-pe-supply = <®_aldo1>; > > + vcc-pf-supply = <®_dcdc1>; > > + vcc-pg-supply = <®_dldo4>; > > + vcc-ph-supply = <®_dcdc1>; > > +}; > > + > > +&r_pio { > > + /* > > + * FIXME: We can't add that supply for now since it would > > + * create a circular dependency between pinctrl, the regulator > > + * and the RSB Bus. > > + * > > + * vcc-pl-supply = <®_aldo2>; > > + */ > > +}; > > + > > +&r_rsb { > > + status = "okay"; > > + > > + axp803: pmic@3a3 { > > + compatible = "x-powers,axp803"; > > + reg = <0x3a3>; > > + interrupt-parent = <&r_intc>; > > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; > > + }; > > +}; > > + > > +#include "axp803.dtsi" > > + > > +&ac_power_supply { > > + status = "okay"; > > +}; > > + > > +&battery_power_supply { > > + status = "okay"; > > +}; > > + > > +®_aldo1 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-name = "dovdd-csi"; > > +}; > > + > > +®_aldo2 { > > + regulator-always-on; > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-name = "vcc-pl"; > > +}; > > + > > +®_aldo3 { > > + regulator-always-on; > > + regulator-min-microvolt = <2700000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "vcc-pll-avcc"; > > +}; > > + > > +®_dcdc1 { > > + regulator-always-on; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "vcc-3v3"; > > +}; > > + > > +®_dcdc2 { > > + regulator-always-on; > > + regulator-min-microvolt = <1000000>; > > + regulator-max-microvolt = <1300000>; > > + regulator-name = "vdd-cpux"; > > +}; > > + > > +/* DCDC3 is polyphased with DCDC2 */ > > + > > +®_dcdc5 { > > + regulator-always-on; > > + regulator-min-microvolt = <1200000>; > > + regulator-max-microvolt = <1200000>; > > + regulator-name = "vcc-dram"; > > +}; > > + > > +®_dcdc6 { > > + regulator-always-on; > > + regulator-min-microvolt = <1100000>; > > + regulator-max-microvolt = <1100000>; > > + regulator-name = "vdd-sys"; > > +}; > > + > > +®_dldo1 { > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "vcc-dsi-sensor"; > > +}; > > + > > +®_dldo2 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-name = "vcc-mipi-io"; > > +}; > > + > > +®_dldo3 { > > + regulator-min-microvolt = <2800000>; > > + regulator-max-microvolt = <2800000>; > > + regulator-name = "avdd-csi"; > > +}; > > + > > +®_dldo4 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "vcc-wifi-io"; > > +}; > > + > > +®_eldo1 { > > + regulator-always-on; > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-name = "vcc-lpddr"; > > +}; > > + > > +®_eldo3 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-name = "dvdd-1v8-csi"; > > +}; > > + > > +®_fldo1 { > > + regulator-min-microvolt = <1200000>; > > + regulator-max-microvolt = <1200000>; > > + regulator-name = "vcc-1v2-hsic"; > > +}; > > + > > +®_fldo2 { > > + regulator-always-on; > > + regulator-min-microvolt = <1100000>; > > + regulator-max-microvolt = <1100000>; > > + regulator-name = "vdd-cpus"; > > +}; > > + > > +®_ldo_io0 { > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "vcc-lcd-ctp-stk"; > > + status = "okay"; > > +}; > > + > > +®_ldo_io1 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-name = "vcc-1v8-typec"; > > + status = "okay"; > > +}; > > + > > +®_rtc_ldo { > > + regulator-name = "vcc-rtc"; > > +}; > > + > > +&sound { > > + status = "okay"; > > + simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>; > > + simple-audio-card,widgets = "Microphone", "Headset Microphone", > > + "Microphone", "Internal Microphone", > > + "Headphone", "Headphone Jack", > > + "Speaker", "Internal Earpiece", > > + "Speaker", "Internal Speaker"; > > + simple-audio-card,routing = > > + "Headphone Jack", "HP", > > + "Internal Earpiece", "EARPIECE", > > + "Internal Speaker", "Speaker Amp OUTL", > > + "Internal Speaker", "Speaker Amp OUTR", > > + "Speaker Amp INL", "LINEOUT", > > + "Speaker Amp INR", "LINEOUT", > > + "Left DAC", "AIF1 Slot 0 Left", > > + "Right DAC", "AIF1 Slot 0 Right", > > + "AIF1 Slot 0 Left ADC", "Left ADC", > > + "AIF1 Slot 0 Right ADC", "Right ADC", > > + "Internal Microphone", "MBIAS", > > + "MIC1", "Internal Microphone", > > + "Headset Microphone", "HBIAS", > > + "MIC2", "Headset Microphone"; > > +}; > > + > > +&uart0 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&uart0_pb_pins>; > > + status = "okay"; > > +}; > > + > > +/* Connected to the modem */ > > +&uart3 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&uart3_pins>; > > That's the default too, and I guess you'd need hardware flow control > here? Hardware flow control is routed badly on the board, and can't be used at the moment on any of the submitted versions. It may be added in 1.2. > > + status = "okay"; > > +}; > > + > > +&usb_otg { > > + dr_mode = "peripheral"; > > + status = "okay"; > > +}; > > + > > +&usb_power_supply { > > + status = "okay"; > > +}; > > + > > +&usbphy { > > + status = "okay"; > > +}; > > -- > > 2.25.1 > > > > Looks good otherwise, thanks! > Maxime Thank you for the review. :) regards, o.
On 2020-02-24 13:56, Ondřej Jirman wrote: > Hello Maxime, > > On Mon, Feb 24, 2020 at 12:00:27PM +0100, Maxime Ripard wrote: >> Hi, >> >> On Sun, Feb 23, 2020 at 06:29:16PM +0100, Ondrej Jirman wrote: >>> At them moment PinePhone comes in two slightly incompatible variants: >>> >>> - 1.0: Early Developer Batch >>> - 1.1: Braveheart Batch >>> >>> There will be at least one more incompatible variant in the very near >>> future, so let's start by sharing the dtsi among multiple variants, >>> right away, even though the HW description doesn't yet include the >>> different bits. >>> >>> This is a basic DT that includes only features that are already >>> supported by mainline drivers. >> >> What are those incompatibilities? It's not really obvious from your >> patch. > > The changes are listed here: > > https://wiki.pine64.org/index.php/PinePhone_v1.1_-_Braveheart#Changes_from_1.0 > > Substantial ones are: > > 2. Swap PC3 to FLASH_EN and PD24 to FLASH_TRIGOUT, where previously they were reversed > 5. Set the EG25G's PWRKEY on by default (see resistor R1526) > 6. Add R630 resistor location, populate with 0K by default. Allows adjusting to > different battery thermistors in case this is not possible in software. > > The incompatiblilities between 1.1 and 1.2 will be more extensive: > > https://wiki.pine64.org/index.php/PinePhone/Power_Management#Suggested_GPIO_Hardware_Changes > >>> Co-developed-by: Samuel Holland <samuel@sholland.org> >>> Signed-off-by: Samuel Holland <samuel@sholland.org> >>> Co-developed-by: Martijn Braam <martijn@brixit.nl> >>> Signed-off-by: Martijn Braam <martijn@brixit.nl> >>> Co-developed-by: Luca Weiss <luca@z3ntu.xyz> >>> Signed-off-by: Luca Weiss <luca@z3ntu.xyz> >>> Signed-off-by: Bhushan Shah <bshah@kde.org> >>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io> >>> Signed-off-by: Ondrej Jirman <megous@megous.com> >>> --- >>> arch/arm64/boot/dts/allwinner/Makefile | 2 + >>> .../allwinner/sun50i-a64-pinephone-1.0.dts | 11 + >>> .../allwinner/sun50i-a64-pinephone-1.1.dts | 11 + >>> .../dts/allwinner/sun50i-a64-pinephone.dtsi | 385 ++++++++++++++++++ >>> 4 files changed, 409 insertions(+) >>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts >>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts >>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi >>> >>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile >>> index cf4f78617c3f3..79ca263672c38 100644 >>> --- a/arch/arm64/boot/dts/allwinner/Makefile >>> +++ b/arch/arm64/boot/dts/allwinner/Makefile >>> @@ -9,6 +9,8 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb >>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb >>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb >>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb >>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.0.dtb >>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.1.dtb >>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb >>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb >>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb >>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts >>> new file mode 100644 >>> index 0000000000000..0c42272106afa >>> --- /dev/null >>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts >>> @@ -0,0 +1,11 @@ >>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >>> +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> >> >> Given the list of authors, surely you're not the sole copyright owner >> here? > > Yes, I made this and the 1.1 dts file by myself. It's not really a meaningful > contribution, since at the moment it's basically empty. I suppose to have > a license, the file requires some author. > > Collaborative work is mostly in the dtsi. > >>> +/dts-v1/; >>> + >>> +#include "sun50i-a64-pinephone.dtsi" >>> + >>> +/ { >>> + model = "Pine64 PinePhone Developer Batch (1.0)"; >>> + compatible = "pine64,pinephone-1.0", "allwinner,sun50i-a64"; >>> +}; >>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts >>> new file mode 100644 >>> index 0000000000000..06a775c41664b >>> --- /dev/null >>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts >>> @@ -0,0 +1,11 @@ >>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >>> +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> >>> + >>> +/dts-v1/; >>> + >>> +#include "sun50i-a64-pinephone.dtsi" >>> + >>> +/ { >>> + model = "Pine64 PinePhone Braveheart (1.1)"; >>> + compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64"; >>> +}; >>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi >>> new file mode 100644 >>> index 0000000000000..d0cf21d82c9e9 >>> --- /dev/null >>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi >>> @@ -0,0 +1,385 @@ >>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) >>> +// Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz> >>> +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> > > For the record. Originally I took this file from: > > https://gitlab.com/pine64-org/linux/commits/pine64-kernel-5.4.y > https://gitlab.com/pine64-org/linux/-/blob/pine64-kernel-5.4.y/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dts > > about a month ago, and kept working on it in my trees for 5.5 and 5.6: > > https://megous.com/git/linux/log/?h=pp-5.5 > https://megous.com/git/linux/log/?h=pp-5.6 > > Adding support for using multiple cameras, bugfixing, and integrating work from > others, and now doing the legwork to strip the more complete DTS and make it > into a mainlainable state, so that collaboration can continue in the mainline > tree. > > AFAIK, at this point (after stripdown), most of the work comes from Icenowy. > With some people contributing "smaller" things. I say "smaller" in quotes, since > I know that there can be a weekend of debugging behind changing a 2-3 lines, and > don't want to minimize anyone's contribution. > > IANAL and I don't know what's entirely apropriate to do here. I've disucssed > this briefly on the IRC with involved people (that are also CCed in this > series), and there was a suggestion to adding a bunch of Cob/SoB tags, based on > some even older DTS file for dontbeevil (developer kit for PinePhone), that the > Icenowy's file was based on. So I did. > > The more copyright holders the better, I guess. :) So if CCed people want to > be added here, and made the contribution to the present file, please state > so for the record again here on the mailing list, and I'll add you to the > header, or anywhere you wish. > Yes please :), I have at least some i2c sensor nodes in this file, probably also a bunch of other minor changes but it's pretty hard to track through the history of the various files and branches. >>> +#include "sun50i-a64.dtsi" >>> +#include "sun50i-a64-cpu-opp.dtsi" >>> + >>> +#include <dt-bindings/gpio/gpio.h> >>> +#include <dt-bindings/input/input.h> >>> +#include <dt-bindings/leds/common.h> >>> +#include <dt-bindings/pwm/pwm.h> >>> + >>> +/ { >>> + aliases { >>> + serial0 = &uart0; >>> + }; >>> + >>> + chosen { >>> + stdout-path = "serial0:115200n8"; >>> + }; >>> + >>> + leds { >>> + compatible = "gpio-leds"; >>> + >>> + blue { >>> + function = LED_FUNCTION_INDICATOR; >>> + function-enumerator = <1>; >>> + color = <LED_COLOR_ID_BLUE>; >>> + gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */ >>> + }; >>> + >>> + green { >>> + function = LED_FUNCTION_INDICATOR; >>> + function-enumerator = <2>; >>> + color = <LED_COLOR_ID_GREEN>; >>> + gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */ >>> + }; >>> + >>> + red { >>> + function = LED_FUNCTION_INDICATOR; >>> + function-enumerator = <3>; >>> + color = <LED_COLOR_ID_RED>; >>> + gpios = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */ >>> + }; >>> + }; >> >> LEDs should be named using the $color:$board:$usage pattern > > Do you mean using a label? It seems label is deprecated, and bindings should > start using function/function-enumerator/color properties now: > > https://elixir.bootlin.com/linux/v5.6-rc2/source/Documentation/devicetree/bindings/leds/common.yaml#L57 > > It doesn't look like the new bindings are used much, yet. I've found: > > https://elixir.bootlin.com/linux/v5.6-rc2/source/arch/arm64/boot/dts/amlogic/meson-gxbb-kii-pro.dts > > and > > https://elixir.bootlin.com/linux/v5.6-rc2/source/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi#L96 > > On PinePhone these are indicator leds with no pre-defined meaning, for > use by the apps to indicate things like a new SMS, or missed call, or > whatever people desire. > >>> + >>> + speaker_amp: audio-amplifier { >>> + compatible = "simple-audio-amplifier"; >>> + enable-gpios = <&pio 2 7 GPIO_ACTIVE_HIGH>; /* PC7 */ >>> + sound-name-prefix = "Speaker Amp"; >>> + }; >>> + >>> + vibrator { >>> + compatible = "gpio-vibrator"; >>> + enable-gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */ >>> + vcc-supply = <®_dcdc1>; >>> + }; >>> +}; >>> + >>> +&codec { >>> + status = "okay"; >>> +}; >>> + >>> +&codec_analog { >>> + cpvdd-supply = <®_eldo1>; >>> + status = "okay"; >>> +}; >>> + >>> +&cpu0 { >>> + cpu-supply = <®_dcdc2>; >>> +}; >>> + >>> +&cpu1 { >>> + cpu-supply = <®_dcdc2>; >>> +}; >>> + >>> +&cpu2 { >>> + cpu-supply = <®_dcdc2>; >>> +}; >>> + >>> +&cpu3 { >>> + cpu-supply = <®_dcdc2>; >>> +}; >>> + >>> +&dai { >>> + status = "okay"; >>> +}; >>> + >>> +&ehci0 { >>> + status = "okay"; >>> +}; >>> + >>> +&ehci1 { >>> + status = "okay"; >>> +}; >>> + >>> +&i2c1 { >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&i2c1_pins>; >> >> That's the default > > Ok. > >>> + status = "okay"; >>> + >>> + /* Magnetometer */ >>> + lis3mdl@1e { >>> + compatible = "st,lis3mdl-magn"; >>> + reg = <0x1e>; >>> + vdd-supply = <®_dldo1>; >>> + vddio-supply = <®_dldo1>; >>> + }; >>> + >>> + /* Accelerometer/gyroscope */ >>> + mpu6050@68 { >>> + compatible = "invensense,mpu6050"; >>> + reg = <0x68>; >>> + interrupt-parent = <&pio>; >>> + interrupts = <7 5 IRQ_TYPE_EDGE_RISING>; /* PH5 */ >>> + vdd-supply = <®_dldo1>; >>> + vddio-supply = <®_dldo1>; >>> + }; >>> +}; >>> + >>> +/* Connected to pogo pins */ >>> +&i2c2 { >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&i2c2_pins>; >> >> That's the default as well > > Actually it is not. There's not i2c2_pins at all in the mainline yet. > >>> + status = "okay"; >>> +}; >> >> And I'm not sure what the pogo pins are? > > It's a common name for spring-loaded pin headers that can be used to connect the > phone to auxiliary devices. 6 pins are visible on this image near the top: > > https://wiki.pine64.org/index.php/File:PinePhone_switches.jpeg > >>> + >>> +&lradc { >>> + vref-supply = <®_aldo3>; >>> + status = "okay"; >>> + >>> + button-200 { >>> + label = "Volume Up"; >>> + linux,code = <KEY_VOLUMEUP>; >>> + channel = <0>; >>> + voltage = <200000>; >>> + }; >>> + >>> + button-400 { >>> + label = "Volume Down"; >>> + linux,code = <KEY_VOLUMEDOWN>; >>> + channel = <0>; >>> + voltage = <400000>; >>> + }; >>> +}; >>> + >>> +&mmc0 { >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&mmc0_pins>; >> >> That's the default > > Ok. > >>> + vmmc-supply = <®_dcdc1>; >>> + vqmmc-supply = <®_dcdc1>; >>> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ >>> + disable-wp; >>> + bus-width = <4>; >>> + status = "okay"; >>> +}; >>> + >>> +&mmc2 { >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&mmc2_pins>; >> >> Ditto > > Will remove. > >>> + vmmc-supply = <®_dcdc1>; >>> + vqmmc-supply = <®_dcdc1>; >>> + bus-width = <8>; >>> + non-removable; >>> + cap-mmc-hw-reset; >>> + status = "okay"; >>> +}; >>> + >>> +&ohci0 { >>> + status = "okay"; >>> +}; >>> + >>> +&ohci1 { >>> + status = "okay"; >>> +}; >>> + >>> +&pio { >>> + vcc-pb-supply = <®_dcdc1>; >>> + vcc-pc-supply = <®_dcdc1>; >>> + vcc-pd-supply = <®_dcdc1>; >>> + vcc-pe-supply = <®_aldo1>; >>> + vcc-pf-supply = <®_dcdc1>; >>> + vcc-pg-supply = <®_dldo4>; >>> + vcc-ph-supply = <®_dcdc1>; >>> +}; >>> + >>> +&r_pio { >>> + /* >>> + * FIXME: We can't add that supply for now since it would >>> + * create a circular dependency between pinctrl, the regulator >>> + * and the RSB Bus. >>> + * >>> + * vcc-pl-supply = <®_aldo2>; >>> + */ >>> +}; >>> + >>> +&r_rsb { >>> + status = "okay"; >>> + >>> + axp803: pmic@3a3 { >>> + compatible = "x-powers,axp803"; >>> + reg = <0x3a3>; >>> + interrupt-parent = <&r_intc>; >>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; >>> + }; >>> +}; >>> + >>> +#include "axp803.dtsi" >>> + >>> +&ac_power_supply { >>> + status = "okay"; >>> +}; >>> + >>> +&battery_power_supply { >>> + status = "okay"; >>> +}; >>> + >>> +®_aldo1 { >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-name = "dovdd-csi"; >>> +}; >>> + >>> +®_aldo2 { >>> + regulator-always-on; >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-name = "vcc-pl"; >>> +}; >>> + >>> +®_aldo3 { >>> + regulator-always-on; >>> + regulator-min-microvolt = <2700000>; >>> + regulator-max-microvolt = <3300000>; >>> + regulator-name = "vcc-pll-avcc"; >>> +}; >>> + >>> +®_dcdc1 { >>> + regulator-always-on; >>> + regulator-min-microvolt = <3300000>; >>> + regulator-max-microvolt = <3300000>; >>> + regulator-name = "vcc-3v3"; >>> +}; >>> + >>> +®_dcdc2 { >>> + regulator-always-on; >>> + regulator-min-microvolt = <1000000>; >>> + regulator-max-microvolt = <1300000>; >>> + regulator-name = "vdd-cpux"; >>> +}; >>> + >>> +/* DCDC3 is polyphased with DCDC2 */ >>> + >>> +®_dcdc5 { >>> + regulator-always-on; >>> + regulator-min-microvolt = <1200000>; >>> + regulator-max-microvolt = <1200000>; >>> + regulator-name = "vcc-dram"; >>> +}; >>> + >>> +®_dcdc6 { >>> + regulator-always-on; >>> + regulator-min-microvolt = <1100000>; >>> + regulator-max-microvolt = <1100000>; >>> + regulator-name = "vdd-sys"; >>> +}; >>> + >>> +®_dldo1 { >>> + regulator-min-microvolt = <3300000>; >>> + regulator-max-microvolt = <3300000>; >>> + regulator-name = "vcc-dsi-sensor"; >>> +}; >>> + >>> +®_dldo2 { >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-name = "vcc-mipi-io"; >>> +}; >>> + >>> +®_dldo3 { >>> + regulator-min-microvolt = <2800000>; >>> + regulator-max-microvolt = <2800000>; >>> + regulator-name = "avdd-csi"; >>> +}; >>> + >>> +®_dldo4 { >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <3300000>; >>> + regulator-name = "vcc-wifi-io"; >>> +}; >>> + >>> +®_eldo1 { >>> + regulator-always-on; >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-name = "vcc-lpddr"; >>> +}; >>> + >>> +®_eldo3 { >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-name = "dvdd-1v8-csi"; >>> +}; >>> + >>> +®_fldo1 { >>> + regulator-min-microvolt = <1200000>; >>> + regulator-max-microvolt = <1200000>; >>> + regulator-name = "vcc-1v2-hsic"; >>> +}; >>> + >>> +®_fldo2 { >>> + regulator-always-on; >>> + regulator-min-microvolt = <1100000>; >>> + regulator-max-microvolt = <1100000>; >>> + regulator-name = "vdd-cpus"; >>> +}; >>> + >>> +®_ldo_io0 { >>> + regulator-min-microvolt = <3300000>; >>> + regulator-max-microvolt = <3300000>; >>> + regulator-name = "vcc-lcd-ctp-stk"; >>> + status = "okay"; >>> +}; >>> + >>> +®_ldo_io1 { >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-name = "vcc-1v8-typec"; >>> + status = "okay"; >>> +}; >>> + >>> +®_rtc_ldo { >>> + regulator-name = "vcc-rtc"; >>> +}; >>> + >>> +&sound { >>> + status = "okay"; >>> + simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>; >>> + simple-audio-card,widgets = "Microphone", "Headset Microphone", >>> + "Microphone", "Internal Microphone", >>> + "Headphone", "Headphone Jack", >>> + "Speaker", "Internal Earpiece", >>> + "Speaker", "Internal Speaker"; >>> + simple-audio-card,routing = >>> + "Headphone Jack", "HP", >>> + "Internal Earpiece", "EARPIECE", >>> + "Internal Speaker", "Speaker Amp OUTL", >>> + "Internal Speaker", "Speaker Amp OUTR", >>> + "Speaker Amp INL", "LINEOUT", >>> + "Speaker Amp INR", "LINEOUT", >>> + "Left DAC", "AIF1 Slot 0 Left", >>> + "Right DAC", "AIF1 Slot 0 Right", >>> + "AIF1 Slot 0 Left ADC", "Left ADC", >>> + "AIF1 Slot 0 Right ADC", "Right ADC", >>> + "Internal Microphone", "MBIAS", >>> + "MIC1", "Internal Microphone", >>> + "Headset Microphone", "HBIAS", >>> + "MIC2", "Headset Microphone"; >>> +}; >>> + >>> +&uart0 { >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&uart0_pb_pins>; >>> + status = "okay"; >>> +}; >>> + >>> +/* Connected to the modem */ >>> +&uart3 { >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&uart3_pins>; >> >> That's the default too, and I guess you'd need hardware flow control >> here? > > Hardware flow control is routed badly on the board, and can't be used at the > moment on any of the submitted versions. It may be added in 1.2. > >>> + status = "okay"; >>> +}; >>> + >>> +&usb_otg { >>> + dr_mode = "peripheral"; >>> + status = "okay"; >>> +}; >>> + >>> +&usb_power_supply { >>> + status = "okay"; >>> +}; >>> + >>> +&usbphy { >>> + status = "okay"; >>> +}; >>> -- >>> 2.25.1 >>> >> >> Looks good otherwise, thanks! >> Maxime > > Thank you for the review. :) > > regards, > o. >
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index cf4f78617c3f3..79ca263672c38 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -9,6 +9,8 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.0.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts new file mode 100644 index 0000000000000..0c42272106afa --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> + +/dts-v1/; + +#include "sun50i-a64-pinephone.dtsi" + +/ { + model = "Pine64 PinePhone Developer Batch (1.0)"; + compatible = "pine64,pinephone-1.0", "allwinner,sun50i-a64"; +}; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts new file mode 100644 index 0000000000000..06a775c41664b --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> + +/dts-v1/; + +#include "sun50i-a64-pinephone.dtsi" + +/ { + model = "Pine64 PinePhone Braveheart (1.1)"; + compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64"; +}; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi new file mode 100644 index 0000000000000..d0cf21d82c9e9 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi @@ -0,0 +1,385 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2019 Icenowy Zheng <icenowy@aosc.xyz> +// Copyright (C) 2020 Ondrej Jirman <megous@megous.com> + +#include "sun50i-a64.dtsi" +#include "sun50i-a64-cpu-opp.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + blue { + function = LED_FUNCTION_INDICATOR; + function-enumerator = <1>; + color = <LED_COLOR_ID_BLUE>; + gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */ + }; + + green { + function = LED_FUNCTION_INDICATOR; + function-enumerator = <2>; + color = <LED_COLOR_ID_GREEN>; + gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */ + }; + + red { + function = LED_FUNCTION_INDICATOR; + function-enumerator = <3>; + color = <LED_COLOR_ID_RED>; + gpios = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */ + }; + }; + + speaker_amp: audio-amplifier { + compatible = "simple-audio-amplifier"; + enable-gpios = <&pio 2 7 GPIO_ACTIVE_HIGH>; /* PC7 */ + sound-name-prefix = "Speaker Amp"; + }; + + vibrator { + compatible = "gpio-vibrator"; + enable-gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */ + vcc-supply = <®_dcdc1>; + }; +}; + +&codec { + status = "okay"; +}; + +&codec_analog { + cpvdd-supply = <®_eldo1>; + status = "okay"; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&cpu1 { + cpu-supply = <®_dcdc2>; +}; + +&cpu2 { + cpu-supply = <®_dcdc2>; +}; + +&cpu3 { + cpu-supply = <®_dcdc2>; +}; + +&dai { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + status = "okay"; + + /* Magnetometer */ + lis3mdl@1e { + compatible = "st,lis3mdl-magn"; + reg = <0x1e>; + vdd-supply = <®_dldo1>; + vddio-supply = <®_dldo1>; + }; + + /* Accelerometer/gyroscope */ + mpu6050@68 { + compatible = "invensense,mpu6050"; + reg = <0x68>; + interrupt-parent = <&pio>; + interrupts = <7 5 IRQ_TYPE_EDGE_RISING>; /* PH5 */ + vdd-supply = <®_dldo1>; + vddio-supply = <®_dldo1>; + }; +}; + +/* Connected to pogo pins */ +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + status = "okay"; +}; + +&lradc { + vref-supply = <®_aldo3>; + status = "okay"; + + button-200 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <200000>; + }; + + button-400 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <400000>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + disable-wp; + bus-width = <4>; + status = "okay"; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&pio { + vcc-pb-supply = <®_dcdc1>; + vcc-pc-supply = <®_dcdc1>; + vcc-pd-supply = <®_dcdc1>; + vcc-pe-supply = <®_aldo1>; + vcc-pf-supply = <®_dcdc1>; + vcc-pg-supply = <®_dldo4>; + vcc-ph-supply = <®_dcdc1>; +}; + +&r_pio { + /* + * FIXME: We can't add that supply for now since it would + * create a circular dependency between pinctrl, the regulator + * and the RSB Bus. + * + * vcc-pl-supply = <®_aldo2>; + */ +}; + +&r_rsb { + status = "okay"; + + axp803: pmic@3a3 { + compatible = "x-powers,axp803"; + reg = <0x3a3>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +#include "axp803.dtsi" + +&ac_power_supply { + status = "okay"; +}; + +&battery_power_supply { + status = "okay"; +}; + +®_aldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dovdd-csi"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pl"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pll-avcc"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-cpux"; +}; + +/* DCDC3 is polyphased with DCDC2 */ + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-dsi-sensor"; +}; + +®_dldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-mipi-io"; +}; + +®_dldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi"; +}; + +®_dldo4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-io"; +}; + +®_eldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-lpddr"; +}; + +®_eldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dvdd-1v8-csi"; +}; + +®_fldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-1v2-hsic"; +}; + +®_fldo2 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_ldo_io0 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-lcd-ctp-stk"; + status = "okay"; +}; + +®_ldo_io1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8-typec"; + status = "okay"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +&sound { + status = "okay"; + simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>; + simple-audio-card,widgets = "Microphone", "Headset Microphone", + "Microphone", "Internal Microphone", + "Headphone", "Headphone Jack", + "Speaker", "Internal Earpiece", + "Speaker", "Internal Speaker"; + simple-audio-card,routing = + "Headphone Jack", "HP", + "Internal Earpiece", "EARPIECE", + "Internal Speaker", "Speaker Amp OUTL", + "Internal Speaker", "Speaker Amp OUTR", + "Speaker Amp INL", "LINEOUT", + "Speaker Amp INR", "LINEOUT", + "Left DAC", "AIF1 Slot 0 Left", + "Right DAC", "AIF1 Slot 0 Right", + "AIF1 Slot 0 Left ADC", "Left ADC", + "AIF1 Slot 0 Right ADC", "Right ADC", + "Internal Microphone", "MBIAS", + "MIC1", "Internal Microphone", + "Headset Microphone", "HBIAS", + "MIC2", "Headset Microphone"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; + +/* Connected to the modem */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + +&usbphy { + status = "okay"; +};