diff mbox series

[6/6] ARM: dts: stm32mp1: Add IoT Box board support

Message ID 20200420173124.27416-7-mani@kernel.org (mailing list archive)
State New, archived
Headers show
Series Add Stinger96 and IoT Box board support | expand

Commit Message

Manivannan Sadhasivam April 20, 2020, 5:31 p.m. UTC 
From: Manivannan Sadhasivam <mani@kernel.org>

IoT Box is an IoT gateway device based on Stinger96 board powered by
STM32MP1 SoC, designed and manufactured by Shiratech Solutions. This
device makes use of Stinger96 board by having it as a base board with
one additional mezzanine on top.

Following are the features exposed by this device in addition to the
Stinger96 board:

* WiFi/BT
* CCS811 VOC sensor
* 2x Digital microphones IM69D130
* 12x WS2812B LEDs

Following peripherals are tested and known to work:

* WiFi/BT
* CCS811

More information about this device can be found in Shiratech website:
https://www.shiratech-solutions.com/products/iot-box/

Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
---
 arch/arm/boot/dts/Makefile                |  1 +
 arch/arm/boot/dts/stm32mp157a-iot-box.dts | 92 +++++++++++++++++++++++
 2 files changed, 93 insertions(+)
 create mode 100644 arch/arm/boot/dts/stm32mp157a-iot-box.dts

Comments

Alexandre TORGUE April 29, 2020, 8:02 a.m. UTC | #1 
Hi Mani

On 4/20/20 7:31 PM, mani@kernel.org wrote:
> From: Manivannan Sadhasivam <mani@kernel.org>
> 
> IoT Box is an IoT gateway device based on Stinger96 board powered by
> STM32MP1 SoC, designed and manufactured by Shiratech Solutions. This
> device makes use of Stinger96 board by having it as a base board with
> one additional mezzanine on top.
> 
> Following are the features exposed by this device in addition to the
> Stinger96 board:
> 
> * WiFi/BT
> * CCS811 VOC sensor
> * 2x Digital microphones IM69D130
> * 12x WS2812B LEDs
> 
> Following peripherals are tested and known to work:
> 
> * WiFi/BT
> * CCS811
> 
> More information about this device can be found in Shiratech website:
> https://www.shiratech-solutions.com/products/iot-box/
> 
> Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
> ---
>   arch/arm/boot/dts/Makefile                |  1 +
>   arch/arm/boot/dts/stm32mp157a-iot-box.dts | 92 +++++++++++++++++++++++
>   2 files changed, 93 insertions(+)
>   create mode 100644 arch/arm/boot/dts/stm32mp157a-iot-box.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 966b81dfffd6..455ec6eb6303 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1030,6 +1030,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
>   	stm32h743i-disco.dtb \
>   	stm32mp157a-avenger96.dtb \
>   	stm32mp157a-dk1.dtb \
> +	stm32mp157a-iot-box.dtb \
>   	stm32mp157a-stinger96.dtb \
>   	stm32mp157c-dhcom-pdk2.dtb \
>   	stm32mp157c-dk2.dtb \
> diff --git a/arch/arm/boot/dts/stm32mp157a-iot-box.dts b/arch/arm/boot/dts/stm32mp157a-iot-box.dts
> new file mode 100644
> index 000000000000..fa1c006ce531
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp157a-iot-box.dts
> @@ -0,0 +1,92 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2020 Manivannan Sadhasivam
> + */
> +
> +/dts-v1/;
> +#include "stm32mp157a-stinger96.dtsi"
> +
> +/ {
> +	model = "Shiratech STM32MP157A IoT Box";
> +	compatible = "shiratech,stm32mp157a-iot-box", "st,stm32mp157";
> +
> +	wlan_pwr: regulator-wlan {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "wl-reg";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +};
> +
> +&i2c2 {
> +	ccs811@5b {
> +		compatible = "ams,ccs811";
> +		reg = <0x5b>;
> +		wakeup-gpios = <&gpioa 12 GPIO_ACTIVE_LOW>;
> +		reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
> +	};
> +};
> +
> +&pinctrl {

Currently all pinmux definition are done in stm32mp15-pinctrl.dtsi file.
Can you move it ?

Otherwise (except commit title) it is ok for me.

thanks
alex

> +	/*
> +	 * Note: The SDMMC2 pins lack external pullups on data lines. Hence,
> +	 * we need to enable it in the SoC.
> +	 */
> +	sdmmc2_b4_pins_pull: sdmmc2-b4-pull {
> +		pins1 {
> +			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
> +				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
> +				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
> +				 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
> +				 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
> +			slew-rate = <1>;
> +			bias-pull-up;
> +		};
> +		pins2 {
> +			pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
> +			slew-rate = <2>;
> +			drive-push-pull;
> +			bias-disable;
> +		};
> +	};
> +};
> +
> +/* WiFi */
> +&sdmmc2 {
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc2_b4_pins_pull>;
> +	pinctrl-1 = <&sdmmc2_b4_od_pins_b>;
> +	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
> +	broken-cd;
> +	non-removable;
> +	st,neg-edge;
> +	bus-width = <1>;
> +	vmmc-supply = <&wlan_pwr>;
> +	status = "okay";
> +
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	brcmf: bcrmf@1 {
> +		reg = <1>;
> +		compatible = "brcm,bcm4329-fmac";
> +	};
> +};
> +
> +/* Bluetooth */
> +&uart4 {
> +	/* Note: HW flow control is broken, hence using custom CTS/RTS gpios */
> +	/delete-property/st,hw-flow-ctrl;
> +	cts-gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
> +	rts-gpios = <&gpiob 0 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +
> +	bluetooth {
> +		shutdown-gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>;
> +		compatible = "brcm,bcm43438-bt";
> +		max-speed = <115200>;
> +	};
> +};
>
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 966b81dfffd6..455ec6eb6303 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1030,6 +1030,7 @@  dtb-$(CONFIG_ARCH_STM32) += \
 	stm32h743i-disco.dtb \
 	stm32mp157a-avenger96.dtb \
 	stm32mp157a-dk1.dtb \
+	stm32mp157a-iot-box.dtb \
 	stm32mp157a-stinger96.dtb \
 	stm32mp157c-dhcom-pdk2.dtb \
 	stm32mp157c-dk2.dtb \
diff --git a/arch/arm/boot/dts/stm32mp157a-iot-box.dts b/arch/arm/boot/dts/stm32mp157a-iot-box.dts
new file mode 100644
index 000000000000..fa1c006ce531
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157a-iot-box.dts
@@ -0,0 +1,92 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Manivannan Sadhasivam
+ */
+
+/dts-v1/;
+#include "stm32mp157a-stinger96.dtsi"
+
+/ {
+	model = "Shiratech STM32MP157A IoT Box";
+	compatible = "shiratech,stm32mp157a-iot-box", "st,stm32mp157";
+
+	wlan_pwr: regulator-wlan {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&i2c2 {
+	ccs811@5b {
+		compatible = "ams,ccs811";
+		reg = <0x5b>;
+		wakeup-gpios = <&gpioa 12 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	/*
+	 * Note: The SDMMC2 pins lack external pullups on data lines. Hence,
+	 * we need to enable it in the SoC.
+	 */
+	sdmmc2_b4_pins_pull: sdmmc2-b4-pull {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+};
+
+/* WiFi */
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_pull>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+	broken-cd;
+	non-removable;
+	st,neg-edge;
+	bus-width = <1>;
+	vmmc-supply = <&wlan_pwr>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* Bluetooth */
+&uart4 {
+	/* Note: HW flow control is broken, hence using custom CTS/RTS gpios */
+	/delete-property/st,hw-flow-ctrl;
+	cts-gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+	rts-gpios = <&gpiob 0 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	bluetooth {
+		shutdown-gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>;
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <115200>;
+	};
+};