diff mbox series

[v2,4/5] iommu/arm-smmu-qcom: Consistently initialize stream mappings

Message ID 20200717001619.325317-5-bjorn.andersson@linaro.org (mailing list archive)
State New, archived
Headers show
Series iommu/arm-smmu: Support maintaining bootloader mappings | expand

Commit Message

Bjorn Andersson July 17, 2020, 12:16 a.m. UTC 
Firmware that traps writes to S2CR to translate BYPASS into FAULT also
ignores writes of type FAULT. As such booting with "disable_bypass" set
will result in all S2CR registers left as configured by the bootloader.

This has been seen to result in indeterministic results, as these
mappings might linger and reference context banks that Linux is
reconfiguring.

Use the fact that BYPASS writes result in FAULT type to force all stream
mappings to FAULT.

Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---

Changes since v1:
- Fixed subject spelling mistake
- Picked up tested-by

 drivers/iommu/arm-smmu-qcom.c | 18 +++++++++++++++++-
 1 file changed, 17 insertions(+), 1 deletion(-)
diff mbox series

Patch

diff --git a/drivers/iommu/arm-smmu-qcom.c b/drivers/iommu/arm-smmu-qcom.c
index d95a5ee8c83c..10eb024981d1 100644
--- a/drivers/iommu/arm-smmu-qcom.c
+++ b/drivers/iommu/arm-smmu-qcom.c
@@ -27,6 +27,7 @@  static int qcom_smmu_cfg_probe(struct arm_smmu_device *smmu)
 {
 	unsigned int last_s2cr = ARM_SMMU_GR0_S2CR(smmu->num_mapping_groups - 1);
 	u32 reg;
+	int i;
 
 	/*
 	 * With some firmware writes to S2CR of type FAULT are ignored, and
@@ -37,9 +38,24 @@  static int qcom_smmu_cfg_probe(struct arm_smmu_device *smmu)
 					    FIELD_PREP(ARM_SMMU_S2CR_CBNDX, 0xff) |
 					    FIELD_PREP(ARM_SMMU_S2CR_PRIVCFG, S2CR_PRIVCFG_DEFAULT));
 	reg = arm_smmu_gr0_read(smmu, last_s2cr);
-	if (FIELD_GET(ARM_SMMU_S2CR_TYPE, reg) != S2CR_TYPE_BYPASS)
+	if (FIELD_GET(ARM_SMMU_S2CR_TYPE, reg) != S2CR_TYPE_BYPASS) {
 		smmu->qcom_bypass_quirk = true;
 
+		/*
+		 * With firmware ignoring writes of type FAULT, booting the
+		 * Linux kernel with disable_bypass disabled (i.e. "enable
+		 * bypass") the initialization during probe will leave mappings
+		 * in an inconsistent state. Avoid this by configuring all
+		 * S2CRs to BYPASS.
+		 */
+		for (i = 0; i < smmu->num_mapping_groups; i++) {
+			smmu->s2crs[i].type = S2CR_TYPE_BYPASS;
+			smmu->s2crs[i].privcfg = S2CR_PRIVCFG_DEFAULT;
+			smmu->s2crs[i].cbndx = 0xff;
+			smmu->s2crs[i].count = 0;
+		}
+	}
+
 	return 0;
 }