| Message ID | 20201016090833.1892-3-thunder.leizhen@huawei.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | eliminate two common errors reported by any yaml on arm64 | expand |
On Fri 16 Oct 04:08 CDT 2020, Zhen Lei wrote: > The scripts/dtc/checks.c requires that the node have empty "dma-ranges" > property must have the same "#address-cells" and "#size-cells" values as > the parent node. Otherwise, the following warnings is reported: > > arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning \ > (dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but \ > its #address-cells (1) differs from / (2) > arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning \ > (dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but \ > its #size-cells (1) differs from / (2) > > Arnd Bergmann figured out why it's necessary: > Also note that the #address-cells=<1> means that any device under > this bus is assumed to only support 32-bit addressing, and DMA will > have to go through a slow swiotlb in the absence of an IOMMU. > > Suggested-by: Arnd Bergmann <arnd@arndb.de> > Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Thanks for fixing this up Zhen! Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> and applied for 5.11. Regards, Bjorn > --- > arch/arm64/boot/dts/qcom/ipq6018.dtsi | 72 +++++++++++++++++------------------ > 1 file changed, 36 insertions(+), 36 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi > index a94dac76bf3fbdd..59e0cbfa2214305 100644 > --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi > +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi > @@ -179,22 +179,22 @@ > }; > > soc: soc { > - #address-cells = <1>; > - #size-cells = <1>; > - ranges = <0 0 0 0xffffffff>; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges = <0 0 0 0 0x0 0xffffffff>; > dma-ranges; > compatible = "simple-bus"; > > prng: qrng@e1000 { > compatible = "qcom,prng-ee"; > - reg = <0xe3000 0x1000>; > + reg = <0x0 0xe3000 0x0 0x1000>; > clocks = <&gcc GCC_PRNG_AHB_CLK>; > clock-names = "core"; > }; > > cryptobam: dma@704000 { > compatible = "qcom,bam-v1.7.0"; > - reg = <0x00704000 0x20000>; > + reg = <0x0 0x00704000 0x0 0x20000>; > interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>; > clocks = <&gcc GCC_CRYPTO_AHB_CLK>; > clock-names = "bam_clk"; > @@ -206,7 +206,7 @@ > > crypto: crypto@73a000 { > compatible = "qcom,crypto-v5.1"; > - reg = <0x0073a000 0x6000>; > + reg = <0x0 0x0073a000 0x0 0x6000>; > clocks = <&gcc GCC_CRYPTO_AHB_CLK>, > <&gcc GCC_CRYPTO_AXI_CLK>, > <&gcc GCC_CRYPTO_CLK>; > @@ -217,7 +217,7 @@ > > tlmm: pinctrl@1000000 { > compatible = "qcom,ipq6018-pinctrl"; > - reg = <0x01000000 0x300000>; > + reg = <0x0 0x01000000 0x0 0x300000>; > interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; > gpio-controller; > #gpio-cells = <2>; > @@ -235,7 +235,7 @@ > > gcc: gcc@1800000 { > compatible = "qcom,gcc-ipq6018"; > - reg = <0x01800000 0x80000>; > + reg = <0x0 0x01800000 0x0 0x80000>; > clocks = <&xo>, <&sleep_clk>; > clock-names = "xo", "sleep_clk"; > #clock-cells = <1>; > @@ -244,17 +244,17 @@ > > tcsr_mutex_regs: syscon@1905000 { > compatible = "syscon"; > - reg = <0x01905000 0x8000>; > + reg = <0x0 0x01905000 0x0 0x8000>; > }; > > tcsr_q6: syscon@1945000 { > compatible = "syscon"; > - reg = <0x01945000 0xe000>; > + reg = <0x0 0x01945000 0x0 0xe000>; > }; > > blsp_dma: dma@7884000 { > compatible = "qcom,bam-v1.7.0"; > - reg = <0x07884000 0x2b000>; > + reg = <0x0 0x07884000 0x0 0x2b000>; > interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; > clocks = <&gcc GCC_BLSP1_AHB_CLK>; > clock-names = "bam_clk"; > @@ -264,7 +264,7 @@ > > blsp1_uart3: serial@78b1000 { > compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; > - reg = <0x078b1000 0x200>; > + reg = <0x0 0x078b1000 0x0 0x200>; > interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>; > clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, > <&gcc GCC_BLSP1_AHB_CLK>; > @@ -276,7 +276,7 @@ > compatible = "qcom,spi-qup-v2.2.1"; > #address-cells = <1>; > #size-cells = <0>; > - reg = <0x078b5000 0x600>; > + reg = <0x0 0x078b5000 0x0 0x600>; > interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; > spi-max-frequency = <50000000>; > clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>, > @@ -291,7 +291,7 @@ > compatible = "qcom,spi-qup-v2.2.1"; > #address-cells = <1>; > #size-cells = <0>; > - reg = <0x078b6000 0x600>; > + reg = <0x0 0x078b6000 0x0 0x600>; > interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; > spi-max-frequency = <50000000>; > clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>, > @@ -306,7 +306,7 @@ > compatible = "qcom,i2c-qup-v2.2.1"; > #address-cells = <1>; > #size-cells = <0>; > - reg = <0x078b6000 0x600>; > + reg = <0x0 0x078b6000 0x0 0x600>; > interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; > clocks = <&gcc GCC_BLSP1_AHB_CLK>, > <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; > @@ -321,7 +321,7 @@ > compatible = "qcom,i2c-qup-v2.2.1"; > #address-cells = <1>; > #size-cells = <0>; > - reg = <0x078b7000 0x600>; > + reg = <0x0 0x078b7000 0x0 0x600>; > interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; > clocks = <&gcc GCC_BLSP1_AHB_CLK>, > <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>; > @@ -336,24 +336,24 @@ > compatible = "qcom,msm-qgic2"; > interrupt-controller; > #interrupt-cells = <0x3>; > - reg = <0x0b000000 0x1000>, /*GICD*/ > - <0x0b002000 0x1000>, /*GICC*/ > - <0x0b001000 0x1000>, /*GICH*/ > - <0x0b004000 0x1000>; /*GICV*/ > + reg = <0x0 0x0b000000 0x0 0x1000>, /*GICD*/ > + <0x0 0x0b002000 0x0 0x1000>, /*GICC*/ > + <0x0 0x0b001000 0x0 0x1000>, /*GICH*/ > + <0x0 0x0b004000 0x0 0x1000>; /*GICV*/ > interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > }; > > watchdog@b017000 { > compatible = "qcom,kpss-wdt"; > interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; > - reg = <0x0b017000 0x40>; > + reg = <0x0 0x0b017000 0x0 0x40>; > clocks = <&sleep_clk>; > timeout-sec = <10>; > }; > > apcs_glb: mailbox@b111000 { > compatible = "qcom,ipq6018-apcs-apps-global"; > - reg = <0x0b111000 0x1000>; > + reg = <0x0 0x0b111000 0x0 0x1000>; > #clock-cells = <1>; > clocks = <&a53pll>, <&xo>; > clock-names = "pll", "xo"; > @@ -362,7 +362,7 @@ > > a53pll: clock@b116000 { > compatible = "qcom,ipq6018-a53pll"; > - reg = <0x0b116000 0x40>; > + reg = <0x0 0x0b116000 0x0 0x40>; > #clock-cells = <0>; > clocks = <&xo>; > clock-names = "xo"; > @@ -377,68 +377,68 @@ > }; > > timer@b120000 { > - #address-cells = <1>; > - #size-cells = <1>; > + #address-cells = <2>; > + #size-cells = <2>; > ranges; > compatible = "arm,armv7-timer-mem"; > - reg = <0x0b120000 0x1000>; > + reg = <0x0 0x0b120000 0x0 0x1000>; > clock-frequency = <19200000>; > > frame@b120000 { > frame-number = <0>; > interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > - reg = <0x0b121000 0x1000>, > - <0x0b122000 0x1000>; > + reg = <0x0 0x0b121000 0x0 0x1000>, > + <0x0 0x0b122000 0x0 0x1000>; > }; > > frame@b123000 { > frame-number = <1>; > interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > - reg = <0xb123000 0x1000>; > + reg = <0x0 0xb123000 0x0 0x1000>; > status = "disabled"; > }; > > frame@b124000 { > frame-number = <2>; > interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; > - reg = <0x0b124000 0x1000>; > + reg = <0x0 0x0b124000 0x0 0x1000>; > status = "disabled"; > }; > > frame@b125000 { > frame-number = <3>; > interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > - reg = <0x0b125000 0x1000>; > + reg = <0x0 0x0b125000 0x0 0x1000>; > status = "disabled"; > }; > > frame@b126000 { > frame-number = <4>; > interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > - reg = <0x0b126000 0x1000>; > + reg = <0x0 0x0b126000 0x0 0x1000>; > status = "disabled"; > }; > > frame@b127000 { > frame-number = <5>; > interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > - reg = <0x0b127000 0x1000>; > + reg = <0x0 0x0b127000 0x0 0x1000>; > status = "disabled"; > }; > > frame@b128000 { > frame-number = <6>; > interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > - reg = <0x0b128000 0x1000>; > + reg = <0x0 0x0b128000 0x0 0x1000>; > status = "disabled"; > }; > }; > > q6v5_wcss: remoteproc@cd00000 { > compatible = "qcom,ipq8074-wcss-pil"; > - reg = <0x0cd00000 0x4040>, > - <0x004ab000 0x20>; > + reg = <0x0 0x0cd00000 0x0 0x4040>, > + <0x0 0x004ab000 0x0 0x20>; > reg-names = "qdsp6", > "rmb"; > interrupts-extended = <&intc GIC_SPI 325 IRQ_TYPE_EDGE_RISING>, > -- > 1.8.3 > >
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi index a94dac76bf3fbdd..59e0cbfa2214305 100644 --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi @@ -179,22 +179,22 @@ }; soc: soc { - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0 0 0xffffffff>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0 0 0 0x0 0xffffffff>; dma-ranges; compatible = "simple-bus"; prng: qrng@e1000 { compatible = "qcom,prng-ee"; - reg = <0xe3000 0x1000>; + reg = <0x0 0xe3000 0x0 0x1000>; clocks = <&gcc GCC_PRNG_AHB_CLK>; clock-names = "core"; }; cryptobam: dma@704000 { compatible = "qcom,bam-v1.7.0"; - reg = <0x00704000 0x20000>; + reg = <0x0 0x00704000 0x0 0x20000>; interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GCC_CRYPTO_AHB_CLK>; clock-names = "bam_clk"; @@ -206,7 +206,7 @@ crypto: crypto@73a000 { compatible = "qcom,crypto-v5.1"; - reg = <0x0073a000 0x6000>; + reg = <0x0 0x0073a000 0x0 0x6000>; clocks = <&gcc GCC_CRYPTO_AHB_CLK>, <&gcc GCC_CRYPTO_AXI_CLK>, <&gcc GCC_CRYPTO_CLK>; @@ -217,7 +217,7 @@ tlmm: pinctrl@1000000 { compatible = "qcom,ipq6018-pinctrl"; - reg = <0x01000000 0x300000>; + reg = <0x0 0x01000000 0x0 0x300000>; interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; @@ -235,7 +235,7 @@ gcc: gcc@1800000 { compatible = "qcom,gcc-ipq6018"; - reg = <0x01800000 0x80000>; + reg = <0x0 0x01800000 0x0 0x80000>; clocks = <&xo>, <&sleep_clk>; clock-names = "xo", "sleep_clk"; #clock-cells = <1>; @@ -244,17 +244,17 @@ tcsr_mutex_regs: syscon@1905000 { compatible = "syscon"; - reg = <0x01905000 0x8000>; + reg = <0x0 0x01905000 0x0 0x8000>; }; tcsr_q6: syscon@1945000 { compatible = "syscon"; - reg = <0x01945000 0xe000>; + reg = <0x0 0x01945000 0x0 0xe000>; }; blsp_dma: dma@7884000 { compatible = "qcom,bam-v1.7.0"; - reg = <0x07884000 0x2b000>; + reg = <0x0 0x07884000 0x0 0x2b000>; interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "bam_clk"; @@ -264,7 +264,7 @@ blsp1_uart3: serial@78b1000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; - reg = <0x078b1000 0x200>; + reg = <0x0 0x078b1000 0x0 0x200>; interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; @@ -276,7 +276,7 @@ compatible = "qcom,spi-qup-v2.2.1"; #address-cells = <1>; #size-cells = <0>; - reg = <0x078b5000 0x600>; + reg = <0x0 0x078b5000 0x0 0x600>; interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; spi-max-frequency = <50000000>; clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>, @@ -291,7 +291,7 @@ compatible = "qcom,spi-qup-v2.2.1"; #address-cells = <1>; #size-cells = <0>; - reg = <0x078b6000 0x600>; + reg = <0x0 0x078b6000 0x0 0x600>; interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; spi-max-frequency = <50000000>; clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>, @@ -306,7 +306,7 @@ compatible = "qcom,i2c-qup-v2.2.1"; #address-cells = <1>; #size-cells = <0>; - reg = <0x078b6000 0x600>; + reg = <0x0 0x078b6000 0x0 0x600>; interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GCC_BLSP1_AHB_CLK>, <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; @@ -321,7 +321,7 @@ compatible = "qcom,i2c-qup-v2.2.1"; #address-cells = <1>; #size-cells = <0>; - reg = <0x078b7000 0x600>; + reg = <0x0 0x078b7000 0x0 0x600>; interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GCC_BLSP1_AHB_CLK>, <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>; @@ -336,24 +336,24 @@ compatible = "qcom,msm-qgic2"; interrupt-controller; #interrupt-cells = <0x3>; - reg = <0x0b000000 0x1000>, /*GICD*/ - <0x0b002000 0x1000>, /*GICC*/ - <0x0b001000 0x1000>, /*GICH*/ - <0x0b004000 0x1000>; /*GICV*/ + reg = <0x0 0x0b000000 0x0 0x1000>, /*GICD*/ + <0x0 0x0b002000 0x0 0x1000>, /*GICC*/ + <0x0 0x0b001000 0x0 0x1000>, /*GICH*/ + <0x0 0x0b004000 0x0 0x1000>; /*GICV*/ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; }; watchdog@b017000 { compatible = "qcom,kpss-wdt"; interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; - reg = <0x0b017000 0x40>; + reg = <0x0 0x0b017000 0x0 0x40>; clocks = <&sleep_clk>; timeout-sec = <10>; }; apcs_glb: mailbox@b111000 { compatible = "qcom,ipq6018-apcs-apps-global"; - reg = <0x0b111000 0x1000>; + reg = <0x0 0x0b111000 0x0 0x1000>; #clock-cells = <1>; clocks = <&a53pll>, <&xo>; clock-names = "pll", "xo"; @@ -362,7 +362,7 @@ a53pll: clock@b116000 { compatible = "qcom,ipq6018-a53pll"; - reg = <0x0b116000 0x40>; + reg = <0x0 0x0b116000 0x0 0x40>; #clock-cells = <0>; clocks = <&xo>; clock-names = "xo"; @@ -377,68 +377,68 @@ }; timer@b120000 { - #address-cells = <1>; - #size-cells = <1>; + #address-cells = <2>; + #size-cells = <2>; ranges; compatible = "arm,armv7-timer-mem"; - reg = <0x0b120000 0x1000>; + reg = <0x0 0x0b120000 0x0 0x1000>; clock-frequency = <19200000>; frame@b120000 { frame-number = <0>; interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x0b121000 0x1000>, - <0x0b122000 0x1000>; + reg = <0x0 0x0b121000 0x0 0x1000>, + <0x0 0x0b122000 0x0 0x1000>; }; frame@b123000 { frame-number = <1>; interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; - reg = <0xb123000 0x1000>; + reg = <0x0 0xb123000 0x0 0x1000>; status = "disabled"; }; frame@b124000 { frame-number = <2>; interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x0b124000 0x1000>; + reg = <0x0 0x0b124000 0x0 0x1000>; status = "disabled"; }; frame@b125000 { frame-number = <3>; interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x0b125000 0x1000>; + reg = <0x0 0x0b125000 0x0 0x1000>; status = "disabled"; }; frame@b126000 { frame-number = <4>; interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x0b126000 0x1000>; + reg = <0x0 0x0b126000 0x0 0x1000>; status = "disabled"; }; frame@b127000 { frame-number = <5>; interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x0b127000 0x1000>; + reg = <0x0 0x0b127000 0x0 0x1000>; status = "disabled"; }; frame@b128000 { frame-number = <6>; interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x0b128000 0x1000>; + reg = <0x0 0x0b128000 0x0 0x1000>; status = "disabled"; }; }; q6v5_wcss: remoteproc@cd00000 { compatible = "qcom,ipq8074-wcss-pil"; - reg = <0x0cd00000 0x4040>, - <0x004ab000 0x20>; + reg = <0x0 0x0cd00000 0x0 0x4040>, + <0x0 0x004ab000 0x0 0x20>; reg-names = "qdsp6", "rmb"; interrupts-extended = <&intc GIC_SPI 325 IRQ_TYPE_EDGE_RISING>,
The scripts/dtc/checks.c requires that the node have empty "dma-ranges" property must have the same "#address-cells" and "#size-cells" values as the parent node. Otherwise, the following warnings is reported: arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning \ (dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but \ its #address-cells (1) differs from / (2) arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning \ (dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but \ its #size-cells (1) differs from / (2) Arnd Bergmann figured out why it's necessary: Also note that the #address-cells=<1> means that any device under this bus is assumed to only support 32-bit addressing, and DMA will have to go through a slow swiotlb in the absence of an IOMMU. Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> --- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 72 +++++++++++++++++------------------ 1 file changed, 36 insertions(+), 36 deletions(-)