| Message ID | 20201124172735.981878-1-lukas@mntre.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | dts: add MNT Reform 2.0 | expand |
Hi Lukas, just some general comments, not a full review. Am Dienstag, den 24.11.2020, 18:27 +0100 schrieb Lukas F. Hartmann: > This is the device tree for the MNT Reform 2.0 open hardware laptop > which is based on NXP i.MX8MQ. It is designed around the Boundary Devices > Nitrogen8M SoM. Since this is based on a module the DT should be split in a module dtsi and a baseboard dts. > Technical details: https://mntre.com/reform > > Signed-off-by: Lukas F. Hartmann <lukas@mntre.com> > --- > .../boot/dts/freescale/imx8mq-mnt-reform2.dts | 783 ++++++++++++++++++ > 1 file changed, 783 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts > > diff --git a/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts > new file mode 100644 > index 000000000..c95a22a1e > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts > @@ -0,1 +1,782 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2018 Boundary Devices > + * Copyright 2019-2020 MNT Research GmbH > + */ > + > +/dts-v1/; > + > +#include "dt-bindings/input/input.h" > +#include "dt-bindings/pwm/pwm.h" > +#include "dt-bindings/usb/pd.h" > +#include "dt-bindings/gpio/gpio.h" > +#include "imx8mq.dtsi" > + > +/ { > + model = "MNT Reform 2"; > + compatible = "fsl,imx8mq"; This needs a more specific compatible. > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + // 4GB of RAM > + memory@40000000 { > + device_type = "memory"; > + reg = <0x00000000 0x40000000 0 0xc0000000>; > + }; Do you need this node? Most bootloaders should be able to patch in the correct amount of memory before passing control to the kernel. > + > + reg_vref_0v9: regulator-vref-0v9 { > + compatible = "regulator-fixed"; > + regulator-name = "vref-0v9"; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <900000>; > + regulator-always-on; > + }; > + > + reg_vref_1v2: regulator-vref-1v2 { > + compatible = "regulator-fixed"; > + regulator-name = "vref-1v2"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + }; > + > + reg_vref_1v8: regulator-vref-1v8 { > + compatible = "regulator-fixed"; > + regulator-name = "vref-1v8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + }; > + > + reg_vref_2v5: regulator-vref-2v5 { > + compatible = "regulator-fixed"; > + regulator-name = "vref-2v5"; > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <2500000>; > + regulator-always-on; > + }; > + > + reg_vref_3v3: regulator-vref-3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "vref-3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + reg_vref_5v: regulator-vref-5v { > + compatible = "regulator-fixed"; > + regulator-name = "vref-5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > + > + backlight: backlight { > + compatible = "pwm-backlight"; > + pwms = <&pwm2 0 10000>; > + enable-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; > + brightness-levels = <0 32 64 128 160 200 255>; > + default-brightness-level = <6>; > + }; > + > + panel { > + compatible = "innolux,n125hce-gn1"; > + power = <®_vref_3v3>; > + backlight = <&backlight>; > + no-hpd; > + > + port@0 { > + panel_in: endpoint { > + remote-endpoint = <&edp_bridge_out>; > + }; > + }; > + }; > + > + sound { > + compatible = "simple-audio-card"; > + simple-audio-card,name = "wm8960-audio"; > + simple-audio-card,format = "i2s"; > + simple-audio-card,frame-master = <&dai_cpu_master>; > + simple-audio-card,bitclock-master = <&dai_cpu_master>; > + > + simple-audio-card,widgets = > + "Microphone", "Mic Jack", > + "Line", "Line In", > + "Line", "Line Out", > + "Speaker", "Speaker", > + "Headphone", "Headphone Jack"; > + simple-audio-card,routing = > + "Headphone Jack", "HP_L", > + "Headphone Jack", "HP_R", > + "Speaker", "SPK_LP", > + "Speaker", "SPK_LN", > + "Speaker", "SPK_RP", > + "Speaker", "SPK_RN", > + "Mic Jack", "MICB", > + "LINPUT1", "Mic Jack", > + "LINPUT2", "Line In", > + "RINPUT2", "Line In"; > + > + dai_cpu_master: simple-audio-card,cpu { > + sound-dai = <&sai2>; > + }; > + > + dailink0: simple-audio-card,codec { > + sound-dai = <&codec>; > + }; > + }; > + > + pcie0_refclk: pcie0-refclk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <100000000>; > + }; > + > + pcie1_refclk: pcie1-refclk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <100000000>; > + }; One of those doesn't actually exist, as I know that one of the PCIe interfaces on the BD module uses the SoC internal refclock. > +}; > + > +&A53_0 { > + cpu-supply = <®_arm_dram>; > +}; > + > +&A53_1 { > + cpu-supply = <®_arm_dram>; > +}; > + > +&A53_2 { > + cpu-supply = <®_arm_dram>; > +}; > + > +&A53_3 { > + cpu-supply = <®_arm_dram>; > +}; > + > +/ { > + soc@0 { > + bus@32c00000 { > + dcss: display-controller@32e00000 { > + status = "okay"; > + > + compatible = "nxp,imx8mq-dcss"; > + reg = <0x32e00000 0x2d000>, <0x32e2f000 0x1000>; > + interrupts = <6>, <8>, <9>; > + interrupt-names = "ctxld", "ctxld_kick", "vblank"; > + interrupt-parent = <&irqsteer>; > + clocks = <&clk IMX8MQ_CLK_DISP_APB_ROOT>, > + <&clk IMX8MQ_CLK_DISP_AXI_ROOT>, > + <&clk IMX8MQ_CLK_DISP_RTRM_ROOT>, > + <&clk IMX8MQ_CLK_DC_PIXEL>, > + <&clk IMX8MQ_CLK_DISP_DTRC>; > + clock-names = "apb", "axi", "rtrm", "pix", "dtrc"; > + assigned-clocks = <&clk IMX8MQ_CLK_DISP_AXI>, > + <&clk IMX8MQ_CLK_DISP_RTRM>, > + <&clk IMX8MQ_VIDEO2_PLL1_REF_SEL>, > + <&clk IMX8MQ_VIDEO_PLL1_REF_SEL>, > + <&clk IMX8MQ_CLK_DC_PIXEL>; > + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_800M>, > + <&clk IMX8MQ_SYS1_PLL_800M>, > + <&clk IMX8MQ_CLK_27M>, > + <&clk IMX8MQ_CLK_25M>, > + <&clk IMX8MQ_VIDEO_PLL1_OUT>; > + assigned-clock-rates = <800000000>, > + <400000000>, > + <27000000>, > + <25000000>, > + <594000000>; This whole node shouldn't be in this DT. I hadn't realized that the DCSS DT patch is not yet upstream. Please work with Shawn and Laurentiu to get this node into the imx8mq.dtsi instead. > + port { > + dcss_dsi_out: endpoint { > + remote-endpoint = <&mipi_dsi_in>; > + }; > + }; > + }; > + }; > + }; > +}; > + > +// LCDIF is not used, but has to be active or DCSS won't work This sounds fishy. There is no dependency between the two interfaces, so you shouldn't need to enable the lcdif to get the dcss working. Do you miss some clock assignment in the dcss node? > +&lcdif { > + status = "okay"; > + /delete-node/ port@0; > +}; > + > +&dphy { > + status = "okay"; > +}; > + > +&fec1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_fec1>; > + phy-mode = "rgmii-id"; > + phy-handle = <ðphy0>; > + fsl,magic-packet; > + status = "okay"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethphy0: ethernet-phy@4 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <4>; > + interrupts = <&gpio1 11 IRQ_TYPE_LEVEL_LOW>; > + reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; > + }; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <400000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + status = "okay"; > + > + // I2C Mux on Nitrogen8M_SOM > + i2cmux@70 { > + compatible = "nxp,pca9546"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1_pca9546>; > + reg = <0x70>; > + reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + i2c1a: i2c1@0 { > + reg = <0>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + // Regulator on Nitrogen8M_SOM > + reg_arm_dram: fan53555@60 { > + compatible = "fcs,fan53555"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_reg_arm_dram>; > + reg = <0x60>; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <1000000>; > + regulator-ramp-delay = <8000>; > + regulator-always-on; > + vsel-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + i2c1b: i2c1@1 { > + reg = <1>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + // Regulator on Nitrogen8M_SOM > + reg_dram_1p1v: fan53555@60 { > + compatible = "fcs,fan53555"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_reg_dram_1p1v>; > + reg = <0x60>; > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + regulator-ramp-delay = <8000>; > + regulator-always-on; > + vsel-gpios = <&gpio2 11 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + i2c1c: i2c1@2 { > + reg = <2>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + // Regulator on Nitrogen8M_SOM > + reg_soc_gpu_vpu: fan53555@60 { > + compatible = "fcs,fan53555"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_reg_soc_gpu_vpu>; > + reg = <0x60>; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <1000000>; > + regulator-ramp-delay = <8000>; > + regulator-always-on; > + vsel-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + // No peripheral connected, available on DSI connector > + i2c1d: i2c1@3 { > + reg = <3>; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + }; > +}; > + > +// No peripheral connected, available on CSI connector > +&i2c2 { > + status = "disabled"; > +}; > + > +&i2c3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3>; > + status = "okay"; > + > + // Audio chip on motherboard > + codec: wm8960@1a { > + compatible = "wlf,wm8960"; > + reg = <0x1a>; > + clocks = <&clk IMX8MQ_CLK_SAI2>; > + clock-names = "mclk"; > + #sound-dai-cells = <0>; > + }; > + > + // Realtime clock chip on motherboard > + pcf8523: pcf8523@68 { > + compatible = "nxp,pcf8523"; > + reg = <0x68>; > + }; > +}; > + > +&i2c4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c4>; > + status = "okay"; > + > + // DSI to eDP converter on motherboard > + edp_bridge: sn65dsi86@2c { > + compatible = "ti,sn65dsi86"; > + reg = <0x2c>; > + enable-gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + edp_bridge_in: endpoint { > + remote-endpoint = <&mipi_dsi_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + edp_bridge_out: endpoint { > + remote-endpoint = <&panel_in>; > + }; > + }; > + }; > + }; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog>; > + > + pinctrl_hog: hoggrp { > + fsl,pins = < > + // WL_EN on Nitrogen8M_SOM, pin 38, goes to /EN input of SN65DSI86 > + MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20 0x19 > + MX8MQ_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x56 > + >; > + }; > + > + pinctrl_fec1: fec1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3 > + MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23 > + MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f > + MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f > + MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f > + MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f > + MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f > + MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f > + MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 > + MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 > + MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 > + MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 > + MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 > + MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 > + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 > + MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x59 > + >; > + }; > + > + pinctrl_i2c1: i2c1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f > + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f > + >; > + }; > + > + pinctrl_i2c1_pca9546: i2c1-pca9546grp { > + fsl,pins = < > + MX8MQ_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x46 > + >; > + }; > + > + pinctrl_i2c2: i2c2grp { > + fsl,pins = < > + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f > + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f > + >; > + }; > + > + pinctrl_i2c3: i2c3grp { > + fsl,pins = < > + MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f > + MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f > + >; > + }; > + > + pinctrl_i2c4: i2c4grp { > + fsl,pins = < > + MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x4000007f > + MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x4000007f > + >; > + }; > + > + pinctrl_pcie0: pcie0grp { > + fsl,pins = < > + MX8MQ_IOMUXC_ECSPI1_MOSI_GPIO5_IO7 0x16 > + >; > + }; > + > + pinctrl_pcie1: pcie1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SAI5_RXD2_GPIO3_IO23 0x16 > + >; > + }; > + > + pinctrl_pwm2: pwm2grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SPDIF_RX_PWM2_OUT 0x16 > + >; > + }; > + > + pinctrl_pwm3: pwm3grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SPDIF_TX_PWM3_OUT 0x16 > + >; > + }; > + > + // Backlight > + pinctrl_pwm4: pwm4grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SAI3_MCLK_PWM4_OUT 0x16 > + >; > + }; > + > + pinctrl_reg_arm_dram: reg-arm-dram { > + fsl,pins = < > + MX8MQ_IOMUXC_SAI5_RXD3_GPIO3_IO24 0x16 > + >; > + }; > + > + pinctrl_reg_dram_1p1v: reg-dram-1p1v { > + fsl,pins = < > + MX8MQ_IOMUXC_SD1_STROBE_GPIO2_IO11 0x16 > + >; > + }; > + > + pinctrl_reg_soc_gpu_vpu: reg-soc-gpu-vpu { > + fsl,pins = < > + MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20 0x16 > + >; > + }; > + > + pinctrl_sai2: sai2grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0xd6 /* Pin 166 */ > + MX8MQ_IOMUXC_SAI2_RXFS_SAI2_RX_SYNC 0xd6 /* Pin 168 */ > + MX8MQ_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6 /* Pin 170 */ > + MX8MQ_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6 /* Pin 172 */ > + MX8MQ_IOMUXC_SAI2_RXC_SAI2_RX_BCLK 0xd6 /* Pin 174 */ > + MX8MQ_IOMUXC_SAI2_MCLK_SAI2_MCLK 0xd6 /* Pin 176 */ > + MX8MQ_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6 /* Pin 168 */ > + >; > + }; > + > + pinctrl_uart1: uart1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x45 > + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x45 > + >; > + }; > + > + pinctrl_uart2: uart2grp { > + fsl,pins = < > + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x45 > + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x45 > + >; > + }; > + > + pinctrl_uart3: uart3grp { > + fsl,pins = < > + MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x45 > + MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x45 > + >; > + }; > + > + pinctrl_usdhc1: usdhc1grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83 > + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3 > + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3 > + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3 > + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3 > + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3 > + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3 > + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3 > + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3 > + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3 > + MX8MQ_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x41 > + >; > + }; > + > + pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { > + fsl,pins = < > + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d > + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd > + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd > + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd > + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd > + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd > + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd > + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd > + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd > + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd > + >; > + }; > + > + pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { > + fsl,pins = < > + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f > + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf > + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf > + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf > + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf > + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf > + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf > + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf > + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf > + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf > + >; > + }; > + > + pinctrl_usdhc2: usdhc2grp { > + fsl,pins = < > + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x03 > + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3 > + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3 > + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3 > + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3 > + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc > + >; > + }; > + > + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { > + fsl,pins = < > + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x0d > + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd > + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd > + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd > + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd > + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd > + >; > + }; > + > + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { > + fsl,pins = < > + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x1e > + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xce > + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xce > + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xce > + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xce > + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xce > + >; > + }; > + > + pinctrl_wdog: wdoggrp { > + fsl,pins = < > + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 > + >; > + }; > +}; iomuxc should be the last node in the DT file. Other nodes should be sorted alphabetically. > + > +&mipi_dsi { > + status = "okay"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0>; > + > + // We don't want input from LCDIF > + /delete-node/ endpoint@0; > + > + mipi_dsi_in: endpoint@1 { > + reg = <1>; > + remote-endpoint = <&dcss_dsi_out>; > + }; > + }; > + port@1 { > + reg = <1>; > + mipi_dsi_out: endpoint { > + remote-endpoint = <&edp_bridge_in>; > + }; > + }; > + }; > +}; > + > +&pcie0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pcie0>; > + reset-gpio = <&gpio5 7 GPIO_ACTIVE_LOW>; > + internal-refclk; This property isn't supported in upstream. The proepr solution would be to point the pcie_bus clock handle to the internal clock and add support to the PCIe driver to notice this fact and program the GPR accordingly. > + > + clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>, > + <&clk IMX8MQ_CLK_PCIE1_AUX>, > + <&clk IMX8MQ_CLK_PCIE1_PHY>, > + <&pcie0_refclk>; > + > + clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; > + > + assigned-clocks = <&clk IMX8MQ_CLK_PCIE1_CTRL>, > + <&clk IMX8MQ_CLK_PCIE1_PHY>; > + assigned-clock-parents = <&clk IMX8MQ_SYS2_PLL_250M>, > + <&clk IMX8MQ_SYS2_PLL_100M>; > + > + status = "okay"; > +}; > + > +&pcie1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pcie1>; > + reset-gpio = <&gpio3 23 GPIO_ACTIVE_LOW>; > + > + clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>, > + <&clk IMX8MQ_CLK_PCIE2_AUX>, > + <&clk IMX8MQ_CLK_PCIE2_PHY>, > + <&pcie1_refclk>; > + clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; > + status = "okay"; > +}; > + > +&pwm2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm2>; > + status = "okay"; > +}; > + > +&pwm3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm3>; > + status = "okay"; > +}; > + > +// Backlight control > +&pwm4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm4>; > + status = "okay"; > +}; > + > +&sai2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sai2>; > + assigned-clocks = <&clk IMX8MQ_CLK_SAI2>; > + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL2_OUT>; > + assigned-clock-rates = <12288000>; > + status = "okay"; > +}; > + > +// Don't use i.MX8M internal RTC because we have a dedicated one > +&snvs_rtc { > + status = "disabled"; > +}; > + > +// Console > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1>; > + status = "okay"; > +}; > + > +// Auxiliary serial port on motherboard > +&uart2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2>; > + status = "okay"; > +}; > + > +// connected to LPC11U24 chip on the motherboard > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3>; > + status = "okay"; > +}; > + > +&usb_dwc3_0 { > + status = "okay"; > + dr_mode = "host"; > +}; > + > +&usb_dwc3_1 { > + status = "okay"; > + dr_mode = "host"; > +}; > + > +&usb3_phy0 { > + vbus-supply = <®_vref_5v>; > + status = "okay"; > +}; > + > +&usb3_phy1 { > + vbus-supply = <®_vref_5v>; > + status = "okay"; > +}; > + > +// eMMC on Nitrogen8M_SOM > +&usdhc1 { > + assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>; > + assigned-clock-rates = <400000000>; > + bus-width = <8>; > + no-mmc-hs400; > + non-removable; no-sd maybe, to speed up enumeration? > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc1>; > + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; > + status = "disabled"; > +}; > + > +// SD Card on motherboard > +&usdhc2 { > + assigned-clocks = <&clk IMX8MQ_CLK_USDHC2>; > + assigned-clock-rates = <200000000>; > + bus-width = <4>; > + no-1-8-v; // We don't support 1.8V signaling This should not be necessary if you instead add a vqmmc-supply and point it to the same fixed 3.3V regulator as the vmmc. > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc2>; > + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; > + vmmc-supply = <®_vref_3v3>; > + status = "okay"; > +}; > + > +&wdog1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_wdog>; > + fsl,ext-reset-output; > + status = "okay"; > +}; > -- > 2.28.0 Regards, Lucas
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts new file mode 100644 index 000000000..c95a22a1e --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts @@ -0,1 +1,782 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2018 Boundary Devices + * Copyright 2019-2020 MNT Research GmbH + */ + +/dts-v1/; + +#include "dt-bindings/input/input.h" +#include "dt-bindings/pwm/pwm.h" +#include "dt-bindings/usb/pd.h" +#include "dt-bindings/gpio/gpio.h" +#include "imx8mq.dtsi" + +/ { + model = "MNT Reform 2"; + compatible = "fsl,imx8mq"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + // 4GB of RAM + memory@40000000 { + device_type = "memory"; + reg = <0x00000000 0x40000000 0 0xc0000000>; + }; + + reg_vref_0v9: regulator-vref-0v9 { + compatible = "regulator-fixed"; + regulator-name = "vref-0v9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-always-on; + }; + + reg_vref_1v2: regulator-vref-1v2 { + compatible = "regulator-fixed"; + regulator-name = "vref-1v2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + reg_vref_1v8: regulator-vref-1v8 { + compatible = "regulator-fixed"; + regulator-name = "vref-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + reg_vref_2v5: regulator-vref-2v5 { + compatible = "regulator-fixed"; + regulator-name = "vref-2v5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_vref_3v3: regulator-vref-3v3 { + compatible = "regulator-fixed"; + regulator-name = "vref-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_vref_5v: regulator-vref-5v { + compatible = "regulator-fixed"; + regulator-name = "vref-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm2 0 10000>; + enable-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + brightness-levels = <0 32 64 128 160 200 255>; + default-brightness-level = <6>; + }; + + panel { + compatible = "innolux,n125hce-gn1"; + power = <®_vref_3v3>; + backlight = <&backlight>; + no-hpd; + + port@0 { + panel_in: endpoint { + remote-endpoint = <&edp_bridge_out>; + }; + }; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "wm8960-audio"; + simple-audio-card,format = "i2s"; + simple-audio-card,frame-master = <&dai_cpu_master>; + simple-audio-card,bitclock-master = <&dai_cpu_master>; + + simple-audio-card,widgets = + "Microphone", "Mic Jack", + "Line", "Line In", + "Line", "Line Out", + "Speaker", "Speaker", + "Headphone", "Headphone Jack"; + simple-audio-card,routing = + "Headphone Jack", "HP_L", + "Headphone Jack", "HP_R", + "Speaker", "SPK_LP", + "Speaker", "SPK_LN", + "Speaker", "SPK_RP", + "Speaker", "SPK_RN", + "Mic Jack", "MICB", + "LINPUT1", "Mic Jack", + "LINPUT2", "Line In", + "RINPUT2", "Line In"; + + dai_cpu_master: simple-audio-card,cpu { + sound-dai = <&sai2>; + }; + + dailink0: simple-audio-card,codec { + sound-dai = <&codec>; + }; + }; + + pcie0_refclk: pcie0-refclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + }; + + pcie1_refclk: pcie1-refclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + }; +}; + +&A53_0 { + cpu-supply = <®_arm_dram>; +}; + +&A53_1 { + cpu-supply = <®_arm_dram>; +}; + +&A53_2 { + cpu-supply = <®_arm_dram>; +}; + +&A53_3 { + cpu-supply = <®_arm_dram>; +}; + +/ { + soc@0 { + bus@32c00000 { + dcss: display-controller@32e00000 { + status = "okay"; + + compatible = "nxp,imx8mq-dcss"; + reg = <0x32e00000 0x2d000>, <0x32e2f000 0x1000>; + interrupts = <6>, <8>, <9>; + interrupt-names = "ctxld", "ctxld_kick", "vblank"; + interrupt-parent = <&irqsteer>; + clocks = <&clk IMX8MQ_CLK_DISP_APB_ROOT>, + <&clk IMX8MQ_CLK_DISP_AXI_ROOT>, + <&clk IMX8MQ_CLK_DISP_RTRM_ROOT>, + <&clk IMX8MQ_CLK_DC_PIXEL>, + <&clk IMX8MQ_CLK_DISP_DTRC>; + clock-names = "apb", "axi", "rtrm", "pix", "dtrc"; + assigned-clocks = <&clk IMX8MQ_CLK_DISP_AXI>, + <&clk IMX8MQ_CLK_DISP_RTRM>, + <&clk IMX8MQ_VIDEO2_PLL1_REF_SEL>, + <&clk IMX8MQ_VIDEO_PLL1_REF_SEL>, + <&clk IMX8MQ_CLK_DC_PIXEL>; + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_800M>, + <&clk IMX8MQ_SYS1_PLL_800M>, + <&clk IMX8MQ_CLK_27M>, + <&clk IMX8MQ_CLK_25M>, + <&clk IMX8MQ_VIDEO_PLL1_OUT>; + assigned-clock-rates = <800000000>, + <400000000>, + <27000000>, + <25000000>, + <594000000>; + + port { + dcss_dsi_out: endpoint { + remote-endpoint = <&mipi_dsi_in>; + }; + }; + }; + }; + }; +}; + +// LCDIF is not used, but has to be active or DCSS won't work +&lcdif { + status = "okay"; + /delete-node/ port@0; +}; + +&dphy { + status = "okay"; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + interrupts = <&gpio1 11 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + // I2C Mux on Nitrogen8M_SOM + i2cmux@70 { + compatible = "nxp,pca9546"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_pca9546>; + reg = <0x70>; + reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + #address-cells = <1>; + #size-cells = <0>; + + i2c1a: i2c1@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + // Regulator on Nitrogen8M_SOM + reg_arm_dram: fan53555@60 { + compatible = "fcs,fan53555"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_arm_dram>; + reg = <0x60>; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1000000>; + regulator-ramp-delay = <8000>; + regulator-always-on; + vsel-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; + }; + }; + + i2c1b: i2c1@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + // Regulator on Nitrogen8M_SOM + reg_dram_1p1v: fan53555@60 { + compatible = "fcs,fan53555"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_dram_1p1v>; + reg = <0x60>; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-ramp-delay = <8000>; + regulator-always-on; + vsel-gpios = <&gpio2 11 GPIO_ACTIVE_HIGH>; + }; + }; + + i2c1c: i2c1@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + // Regulator on Nitrogen8M_SOM + reg_soc_gpu_vpu: fan53555@60 { + compatible = "fcs,fan53555"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_soc_gpu_vpu>; + reg = <0x60>; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1000000>; + regulator-ramp-delay = <8000>; + regulator-always-on; + vsel-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>; + }; + }; + + // No peripheral connected, available on DSI connector + i2c1d: i2c1@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; +}; + +// No peripheral connected, available on CSI connector +&i2c2 { + status = "disabled"; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + // Audio chip on motherboard + codec: wm8960@1a { + compatible = "wlf,wm8960"; + reg = <0x1a>; + clocks = <&clk IMX8MQ_CLK_SAI2>; + clock-names = "mclk"; + #sound-dai-cells = <0>; + }; + + // Realtime clock chip on motherboard + pcf8523: pcf8523@68 { + compatible = "nxp,pcf8523"; + reg = <0x68>; + }; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + // DSI to eDP converter on motherboard + edp_bridge: sn65dsi86@2c { + compatible = "ti,sn65dsi86"; + reg = <0x2c>; + enable-gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + edp_bridge_in: endpoint { + remote-endpoint = <&mipi_dsi_out>; + }; + }; + + port@1 { + reg = <1>; + + edp_bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + // WL_EN on Nitrogen8M_SOM, pin 38, goes to /EN input of SN65DSI86 + MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20 0x19 + MX8MQ_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x56 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23 + MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 + MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x59 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f + >; + }; + + pinctrl_i2c1_pca9546: i2c1-pca9546grp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x46 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f + MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x4000007f + MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x4000007f + >; + }; + + pinctrl_pcie0: pcie0grp { + fsl,pins = < + MX8MQ_IOMUXC_ECSPI1_MOSI_GPIO5_IO7 0x16 + >; + }; + + pinctrl_pcie1: pcie1grp { + fsl,pins = < + MX8MQ_IOMUXC_SAI5_RXD2_GPIO3_IO23 0x16 + >; + }; + + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX8MQ_IOMUXC_SPDIF_RX_PWM2_OUT 0x16 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX8MQ_IOMUXC_SPDIF_TX_PWM3_OUT 0x16 + >; + }; + + // Backlight + pinctrl_pwm4: pwm4grp { + fsl,pins = < + MX8MQ_IOMUXC_SAI3_MCLK_PWM4_OUT 0x16 + >; + }; + + pinctrl_reg_arm_dram: reg-arm-dram { + fsl,pins = < + MX8MQ_IOMUXC_SAI5_RXD3_GPIO3_IO24 0x16 + >; + }; + + pinctrl_reg_dram_1p1v: reg-dram-1p1v { + fsl,pins = < + MX8MQ_IOMUXC_SD1_STROBE_GPIO2_IO11 0x16 + >; + }; + + pinctrl_reg_soc_gpu_vpu: reg-soc-gpu-vpu { + fsl,pins = < + MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20 0x16 + >; + }; + + pinctrl_sai2: sai2grp { + fsl,pins = < + MX8MQ_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0xd6 /* Pin 166 */ + MX8MQ_IOMUXC_SAI2_RXFS_SAI2_RX_SYNC 0xd6 /* Pin 168 */ + MX8MQ_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6 /* Pin 170 */ + MX8MQ_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6 /* Pin 172 */ + MX8MQ_IOMUXC_SAI2_RXC_SAI2_RX_BCLK 0xd6 /* Pin 174 */ + MX8MQ_IOMUXC_SAI2_MCLK_SAI2_MCLK 0xd6 /* Pin 176 */ + MX8MQ_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6 /* Pin 168 */ + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x45 + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x45 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x45 + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x45 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x45 + MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x45 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83 + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3 + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3 + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3 + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3 + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3 + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3 + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3 + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3 + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3 + MX8MQ_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x41 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x03 + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3 + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3 + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3 + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3 + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x0d + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x1e + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xce + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xce + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xce + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xce + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xce + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +}; + +&mipi_dsi { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + // We don't want input from LCDIF + /delete-node/ endpoint@0; + + mipi_dsi_in: endpoint@1 { + reg = <1>; + remote-endpoint = <&dcss_dsi_out>; + }; + }; + port@1 { + reg = <1>; + mipi_dsi_out: endpoint { + remote-endpoint = <&edp_bridge_in>; + }; + }; + }; +}; + +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie0>; + reset-gpio = <&gpio5 7 GPIO_ACTIVE_LOW>; + internal-refclk; + + clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>, + <&clk IMX8MQ_CLK_PCIE1_AUX>, + <&clk IMX8MQ_CLK_PCIE1_PHY>, + <&pcie0_refclk>; + + clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + + assigned-clocks = <&clk IMX8MQ_CLK_PCIE1_CTRL>, + <&clk IMX8MQ_CLK_PCIE1_PHY>; + assigned-clock-parents = <&clk IMX8MQ_SYS2_PLL_250M>, + <&clk IMX8MQ_SYS2_PLL_100M>; + + status = "okay"; +}; + +&pcie1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie1>; + reset-gpio = <&gpio3 23 GPIO_ACTIVE_LOW>; + + clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>, + <&clk IMX8MQ_CLK_PCIE2_AUX>, + <&clk IMX8MQ_CLK_PCIE2_PHY>, + <&pcie1_refclk>; + clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + status = "okay"; +}; + +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; + status = "okay"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "okay"; +}; + +// Backlight control +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm4>; + status = "okay"; +}; + +&sai2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai2>; + assigned-clocks = <&clk IMX8MQ_CLK_SAI2>; + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL2_OUT>; + assigned-clock-rates = <12288000>; + status = "okay"; +}; + +// Don't use i.MX8M internal RTC because we have a dedicated one +&snvs_rtc { + status = "disabled"; +}; + +// Console +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +// Auxiliary serial port on motherboard +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +// connected to LPC11U24 chip on the motherboard +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usb_dwc3_0 { + status = "okay"; + dr_mode = "host"; +}; + +&usb_dwc3_1 { + status = "okay"; + dr_mode = "host"; +}; + +&usb3_phy0 { + vbus-supply = <®_vref_5v>; + status = "okay"; +}; + +&usb3_phy1 { + vbus-supply = <®_vref_5v>; + status = "okay"; +}; + +// eMMC on Nitrogen8M_SOM +&usdhc1 { + assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>; + assigned-clock-rates = <400000000>; + bus-width = <8>; + no-mmc-hs400; + non-removable; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + status = "disabled"; +}; + +// SD Card on motherboard +&usdhc2 { + assigned-clocks = <&clk IMX8MQ_CLK_USDHC2>; + assigned-clock-rates = <200000000>; + bus-width = <4>; + no-1-8-v; // We don't support 1.8V signaling + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + vmmc-supply = <®_vref_3v3>; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; --
This is the device tree for the MNT Reform 2.0 open hardware laptop which is based on NXP i.MX8MQ. It is designed around the Boundary Devices Nitrogen8M SoM. Technical details: https://mntre.com/reform Signed-off-by: Lukas F. Hartmann <lukas@mntre.com> --- .../boot/dts/freescale/imx8mq-mnt-reform2.dts | 783 ++++++++++++++++++ 1 file changed, 783 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts 2.28.0