[v3,2/2] ARM: dts: add Protonic MVT board

Message ID	20210106090414.2344-3-o.rempel@pengutronix.de (mailing list archive)
State	New, archived
Headers	show Return-Path: <SRS0=c6Tt=GJ=lists.infradead.org=linux-arm-kernel-bounces+linux-arm-kernel=archiver.kernel.org@kernel.org> DMARC-Filter: OpenDMARC Filter v1.3.2 mail.kernel.org 73B9A2310A From: Oleksij Rempel <o.rempel@pengutronix.de> To: Mark Rutland <mark.rutland@arm.com>, Rob Herring <robh+dt@kernel.org>, Sascha Hauer <s.hauer@pengutronix.de>, Shawn Guo <shawnguo@kernel.org> Subject: [PATCH v3 2/2] ARM: dts: add Protonic MVT board Date: Wed, 6 Jan 2021 10:04:14 +0100 Message-Id: <20210106090414.2344-3-o.rempel@pengutronix.de> In-Reply-To: <20210106090414.2344-1-o.rempel@pengutronix.de> References: <20210106090414.2344-1-o.rempel@pengutronix.de> MIME-Version: 1.0 Precedence: list Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, Oleksij Rempel <o.rempel@pengutronix.de>, NXP Linux Team <linux-imx@nxp.com>, Pengutronix Kernel Team <kernel@pengutronix.de>, David Jander <david@protonic.nl>, Fabio Estevam <festevam@gmail.com>, linux-arm-kernel@lists.infradead.org Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Sender: "linux-arm-kernel" <linux-arm-kernel-bounces@lists.infradead.org> Errors-To: linux-arm-kernel-bounces+linux-arm-kernel=archiver.kernel.org@lists.infradead.org
Series	mainline Protonic MVT board \| expand [v3,0/2] mainline Protonic MVT board [v3,1/2] dt-bindings: arm: fsl: add Protonic MVT board [v3,2/2] ARM: dts: add Protonic MVT board

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b5b2c176947a..b727542c105b 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -467,6 +467,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-pico-pi.dtb \ imx6dl-plybas.dtb \ imx6dl-plym2m.dtb \ + imx6dl-prtmvt.dtb \ imx6dl-prtrvt.dtb \ imx6dl-prtvt7.dtb \ imx6dl-rex-basic.dtb \ diff --git a/arch/arm/boot/dts/imx6dl-prtmvt.dts b/arch/arm/boot/dts/imx6dl-prtmvt.dts new file mode 100644 index 000000000000..a35a1c66e770 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-prtmvt.dts @@ -0,0 +1,852 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (c) 2016 Protonic Holland + * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix + */ + +/dts-v1/; +#include <dt-bindings/display/sdtv-standards.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/media/tvp5150.h> +#include <dt-bindings/sound/fsl-imx-audmux.h> +#include "imx6dl.dtsi" + +/ { + model = "Protonic MVT board"; + compatible = "prt,prtmvt", "fsl,imx6dl"; + + chosen { + stdout-path = &uart4; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_backlight>; + pwms = <&pwm1 0 5000000 0>; + brightness-levels = <0 16 64 255>; + num-interpolated-steps = <16>; + default-brightness-level = <1>; + power-supply = <&reg_3v3>; + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; + }; + + connector { + compatible = "composite-video-connector"; + label = "Composite0"; + sdtv-standards = <SDTV_STD_PAL_B>; + + port { + comp0_out: endpoint { + remote-endpoint = <&tvp5150_comp0_in>; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpiokeys>; + autorepeat; + + power { + label = "Power Button"; + gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + wakeup-source; + }; + + f1 { + label = "GPIO Key F1"; + linux,code = <KEY_F1>; + gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>; + }; + + f2 { + label = "GPIO Key F2"; + linux,code = <KEY_F2>; + gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>; + }; + + f3 { + label = "GPIO Key F3"; + linux,code = <KEY_F3>; + gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>; + }; + + f4 { + label = "GPIO Key F4"; + linux,code = <KEY_F4>; + gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>; + }; + + f5 { + label = "GPIO Key F5"; + linux,code = <KEY_F5>; + gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>; + }; + + cycle { + label = "GPIO Key CYCLE"; + linux,code = <KEY_CYCLEWINDOWS>; + gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>; + }; + + esc { + label = "GPIO Key ESC"; + linux,code = <KEY_ESC>; + gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>; + }; + + up { + label = "GPIO Key UP"; + linux,code = <KEY_UP>; + gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>; + }; + + down { + label = "GPIO Key DOWN"; + linux,code = <KEY_DOWN>; + gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>; + }; + + ok { + label = "GPIO Key OK"; + linux,code = <KEY_OK>; + gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>; + }; + + f6 { + label = "GPIO Key F6"; + linux,code = <KEY_F6>; + gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>; + }; + + f7 { + label = "GPIO Key F7"; + linux,code = <KEY_F7>; + gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>; + }; + + f8 { + label = "GPIO Key F8"; + linux,code = <KEY_F8>; + gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>; + }; + + f9 { + label = "GPIO Key F9"; + linux,code = <KEY_F9>; + gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>; + }; + + f10 { + label = "GPIO Key F10"; + linux,code = <KEY_F10>; + gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>; + }; + + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + led-0 { + label = "debug0"; + function = LED_FUNCTION_HEARTBEAT; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + led-1 { + label = "debug1"; + function = LED_FUNCTION_DISK; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "disk-activity"; + }; + + led-2 { + label = "power_led"; + function = LED_FUNCTION_POWER; + gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + panel { + compatible = "kyo,tcg070wvlq", "lg,lb070wv8"; + backlight = <&backlight>; + power-supply = <&reg_3v3>; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; + + clk50m_phy: phy-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + }; + + reg_1v8: regulator-1v8 { + compatible = "regulator-fixed"; + regulator-name = "1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_h1_vbus: regulator-h1-vbus { + compatible = "regulator-fixed"; + regulator-name = "h1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_otg_vbus: regulator-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "otg-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "prti6q-sgtl5000"; + simple-audio-card,format = "i2s"; + simple-audio-card,widgets = + "Microphone", "Microphone Jack", + "Line", "Line In Jack", + "Headphone", "Headphone Jack", + "Speaker", "External Speaker"; + simple-audio-card,routing = + "MIC_IN", "Microphone Jack", + "LINE_IN", "Line In Jack", + "Headphone Jack", "HP_OUT", + "External Speaker", "LINE_OUT"; + + simple-audio-card,cpu { + sound-dai = <&ssi1>; + system-clock-frequency = <0>; + }; + + simple-audio-card,codec { + sound-dai = <&codec>; + bitclock-master; + frame-master; + }; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; + + mux-ssi1 { + fsl,audmux-port = <0>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN 0 + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0 + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0 + IMX_AUDMUX_V2_PTCR_TFSDIR 0 + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2) + >; + }; + + mux-pins3 { + fsl,audmux-port = <2>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0) + 0 IMX_AUDMUX_V2_PDCR_TXRXEN + >; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can2>; + status = "okay"; +}; + +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>; +}; + +&ecspi1 { + cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rmii"; + clocks = <&clks IMX6QDL_CLK_ENET>, + <&clks IMX6QDL_CLK_ENET>, + <&clk50m_phy>; + clock-names = "ipg", "ahb", "ptp"; + phy-handle = <&rmii_phy>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* Microchip KSZ8081RNA PHY */ + rmii_phy: ethernet-phy@0 { + reg = <0>; + interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <3000>; + }; + }; +}; + +&gpio1 { + gpio-line-names = + "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR", + "CAM2_MIRROR", "", "", "SMBALERT", + "DEBUG_0", "DEBUG_1", "", "", "", "", "", "", + "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK", + "SD1_DATA3", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio2 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4", + "BOARD_ID0", "BOARD_ID1", "BOARD_ID2", + "", "", "", "", "", "", "", "ON_SWITCH", + "POWER_LED", "", "", "", "", "", "", ""; +}; + +&gpio3 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1", + "CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ", + "TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0", + "YACO_RESET"; +}; + +&gpio4 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX", + "", "", "DIP1_FB", "", "", "", "", "", + "CPU_LIGHT_ON", "", "ETH_RESET", "", "BL_EN", + "BL_PWM", "ETH_INTRP", ""; +}; + +&gpio5 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX", + "YACO_AUX_TX", "ITU656_D0", "ITU656_D1"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + codec: audio-codec@a { + compatible = "fsl,sgtl5000"; + reg = <0xa>; + #sound-dai-cells = <0>; + clocks = <&clks 201>; + VDDA-supply = <&reg_3v3>; + VDDIO-supply = <&reg_3v3>; + VDDD-supply = <&reg_1v8>; + }; + + video@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tvp5150_comp0_in: endpoint { + remote-endpoint = <&comp0_out>; + }; + }; + + /* Output port 2 is video output pad */ + port@2 { + reg = <2>; + tvp5151_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + }; + }; + }; + + gpio_pca: gpio@74 { + compatible = "nxp,pca9539"; + reg = <0x74>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pca9539>; + interrupt-parent = <&gpio4>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + gpio-controller; + #gpio-cells = <2>; + }; + + /* additional i2c devices are added automatically by the boot loader */ +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + adc@49 { + compatible = "ti,ads1015"; + reg = <0x49>; + #address-cells = <1>; + #size-cells = <0>; + + channel@4 { + reg = <4>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@5 { + reg = <5>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@6 { + reg = <6>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@7 { + reg = <7>; + ti,gain = <3>; + ti,datarate = <3>; + }; + }; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + + temperature-sensor@70 { + compatible = "ti,tmp103"; + reg = <0x70>; + }; +}; + +&ipu1_csi0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ipu1_csi0>; + status = "okay"; +}; + +&ipu1_csi0_mux_from_parallel_sensor { + remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>; +}; + +&ldb { + status = "okay"; + + lvds-channel@0 { + status = "okay"; + + port@4 { + reg = <4>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&ssi1 { + #sound-dai-cells = <0>; + fsl,mode = "ac97-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <&reg_h1_vbus>; + pinctrl-names = "default"; + phy_type = "utmi"; + dr_mode = "host"; + status = "okay"; +}; + +&usbotg { + vbus-supply = <&reg_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + phy_type = "utmi"; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + no-1-8-v; + disable-wp; + cap-sd-highspeed; + no-mmc; + no-sdio; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + bus-width = <8>; + no-1-8-v; + non-removable; + no-sd; + no-sdio; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + /* SGTL5000 sys_mclk */ + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0 + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_backlight: backlightgrp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0 + >; + }; + + pinctrl_can1: can1grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000 + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008 + /* CAN1_SR */ + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008 + /* CAN1_TERM */ + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088 + >; + }; + + pinctrl_can2: can2grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000 + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008 + /* CAN2_SR */ + MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + /* CS */ + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + /* MX6QDL_ENET_PINGRP4 */ + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0 + /* nINTRP */ + MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0 + >; + }; + + pinctrl_gpiokeys: gpiokeygrp { + fsl,pins = < + /* nON_SWITCH */ + MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0 + >; + }; + + pinctrl_hog: hoggrp { + fsl,pins = < + /* ITU656_nRESET */ + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 + /* CAM1_MIRROR */ + MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0 + /* CAM2_MIRROR */ + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0 + /* CAM_nDETECT */ + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 + /* ISB_IN1 */ + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0 + /* ISB_nIN2 */ + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0 + /* WARN_LIGHT */ + MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0 + /* ON2_FB */ + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0 + /* YACO_nIRQ */ + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0 + /* YACO_BOOT0 */ + MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0 + /* YACO_nRESET */ + MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0 + /* FORCE_ON1 */ + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 + /* AUDIO_nRESET */ + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0 + /* ITU656_nPDN */ + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0 + + /* HW revision detect */ + /* REV_ID0 */ + MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 + /* REV_ID1 */ + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 + /* REV_ID2 */ + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 + /* REV_ID3 */ + MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 + /* REV_ID4 */ + MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 + + /* New in HW revision 1 */ + /* ON1_FB */ + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0 + /* DIP1_FB */ + MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1 + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_ipu1_csi0: ipu1csi0grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0 + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0 + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0 + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0 + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0 + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0 + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0 + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0 + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + /* DEBUG0 */ + MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0 + /* DEBUG1 */ + MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0 + /* POWER_LED */ + MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0 + >; + }; + + pinctrl_pca9539: pca9539 { + fsl,pins = < + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0 + >; + }; + + /* YaCO AUX Uart */ + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + /* YaCO Touchscreen UART */ + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0 + /* power enable, high active */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099 + MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1 + >; + }; +};

[v3,2/2] ARM: dts: add Protonic MVT board

Commit Message

Patch