| Message ID | 20210223041737.171274-1-joel@jms.id.au (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | fsi: aspeed: Emit fewer barriers in opb operations | expand |
Hey Joel,
diff --git a/drivers/fsi/fsi-master-aspeed.c b/drivers/fsi/fsi-master-aspeed.c
index 90dbe58ca1ed..09fff86b2bac 100644
--- a/drivers/fsi/fsi-master-aspeed.c
+++ b/drivers/fsi/fsi-master-aspeed.c
@@ -101,11 +101,11 @@ static int __opb_write(struct fsi_master_aspeed *aspeed, u32 addr,
u32 reg, status;
int ret;
- writel(CMD_WRITE, base + OPB0_RW);
- writel(transfer_size, base + OPB0_XFER_SIZE);
- writel(addr, base + OPB0_FSI_ADDR);
- writel(val, base + OPB0_FSI_DATA_W);
- writel(0x1, base + OPB_IRQ_CLEAR);
+ writel_relaxed(CMD_WRITE, base + OPB0_RW);
+ writel_relaxed(transfer_size, base + OPB0_XFER_SIZE);
+ writel_relaxed(addr, base + OPB0_FSI_ADDR);
+ writel_relaxed(val, base + OPB0_FSI_DATA_W);
+ writel_relaxed(0x1, base + OPB_IRQ_CLEAR);
writel(0x1, base + OPB_TRIGGER);
Future-joel is going to be angry at you if you don't add a comment
about the ordering requirements there.
Otherwise,
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Cheers,
Jeremy
On Tue, 2021-02-23 at 14:47 +1030, Joel Stanley wrote: > When setting up a read or write to the OPB memory space, we must > perform > five or six AHB writes. The ordering of these up until the trigger > write > does not matter, so use writel_relaxed. Reviewed-by: Eddie James <eajames@linux.ibm.com> I have also tested this patch on hardware, so Tested-by: Eddie James <eajames@linux.ibm.com> > > The generated code goes from (Debian GCC 10.2.1-6): > > mov r8, r3 > mcr 15, 0, sl, cr7, cr10, {4} > str sl, [r6, #20] > mcr 15, 0, sl, cr7, cr10, {4} > str r3, [r6, #24] > mcr 15, 0, sl, cr7, cr10, {4} > str r1, [r6, #28] > mcr 15, 0, sl, cr7, cr10, {4} > str r2, [r6, #32] > mcr 15, 0, sl, cr7, cr10, {4} > mov r1, #1 > str r1, [r6, #64] ; 0x40 > mcr 15, 0, sl, cr7, cr10, {4} > str r1, [r6, #4] > > to this: > > str r3, [r7, #20] > str r2, [r7, #24] > str r1, [r7, #28] > str r3, [r7, #64] > mov r8, #0 > mcr 15, 0, r8, cr7, cr10, {4} > str r3, [r7, #4] > > Signed-off-by: Joel Stanley <joel@jms.id.au> > --- > drivers/fsi/fsi-master-aspeed.c | 18 +++++++++--------- > 1 file changed, 9 insertions(+), 9 deletions(-) > > diff --git a/drivers/fsi/fsi-master-aspeed.c b/drivers/fsi/fsi- > master-aspeed.c > index 90dbe58ca1ed..09fff86b2bac 100644 > --- a/drivers/fsi/fsi-master-aspeed.c > +++ b/drivers/fsi/fsi-master-aspeed.c > @@ -101,11 +101,11 @@ static int __opb_write(struct fsi_master_aspeed > *aspeed, u32 addr, > u32 reg, status; > int ret; > > - writel(CMD_WRITE, base + OPB0_RW); > - writel(transfer_size, base + OPB0_XFER_SIZE); > - writel(addr, base + OPB0_FSI_ADDR); > - writel(val, base + OPB0_FSI_DATA_W); > - writel(0x1, base + OPB_IRQ_CLEAR); > + writel_relaxed(CMD_WRITE, base + OPB0_RW); > + writel_relaxed(transfer_size, base + OPB0_XFER_SIZE); > + writel_relaxed(addr, base + OPB0_FSI_ADDR); > + writel_relaxed(val, base + OPB0_FSI_DATA_W); > + writel_relaxed(0x1, base + OPB_IRQ_CLEAR); > writel(0x1, base + OPB_TRIGGER); > > ret = readl_poll_timeout(base + OPB_IRQ_STATUS, reg, > @@ -149,10 +149,10 @@ static int __opb_read(struct fsi_master_aspeed > *aspeed, uint32_t addr, > u32 result, reg; > int status, ret; > > - writel(CMD_READ, base + OPB0_RW); > - writel(transfer_size, base + OPB0_XFER_SIZE); > - writel(addr, base + OPB0_FSI_ADDR); > - writel(0x1, base + OPB_IRQ_CLEAR); > + writel_relaxed(CMD_READ, base + OPB0_RW); > + writel_relaxed(transfer_size, base + OPB0_XFER_SIZE); > + writel_relaxed(addr, base + OPB0_FSI_ADDR); > + writel_relaxed(0x1, base + OPB_IRQ_CLEAR); > writel(0x1, base + OPB_TRIGGER); > > ret = readl_poll_timeout(base + OPB_IRQ_STATUS, reg,
diff --git a/drivers/fsi/fsi-master-aspeed.c b/drivers/fsi/fsi-master-aspeed.c index 90dbe58ca1ed..09fff86b2bac 100644 --- a/drivers/fsi/fsi-master-aspeed.c +++ b/drivers/fsi/fsi-master-aspeed.c @@ -101,11 +101,11 @@ static int __opb_write(struct fsi_master_aspeed *aspeed, u32 addr, u32 reg, status; int ret; - writel(CMD_WRITE, base + OPB0_RW); - writel(transfer_size, base + OPB0_XFER_SIZE); - writel(addr, base + OPB0_FSI_ADDR); - writel(val, base + OPB0_FSI_DATA_W); - writel(0x1, base + OPB_IRQ_CLEAR); + writel_relaxed(CMD_WRITE, base + OPB0_RW); + writel_relaxed(transfer_size, base + OPB0_XFER_SIZE); + writel_relaxed(addr, base + OPB0_FSI_ADDR); + writel_relaxed(val, base + OPB0_FSI_DATA_W); + writel_relaxed(0x1, base + OPB_IRQ_CLEAR); writel(0x1, base + OPB_TRIGGER); ret = readl_poll_timeout(base + OPB_IRQ_STATUS, reg, @@ -149,10 +149,10 @@ static int __opb_read(struct fsi_master_aspeed *aspeed, uint32_t addr, u32 result, reg; int status, ret; - writel(CMD_READ, base + OPB0_RW); - writel(transfer_size, base + OPB0_XFER_SIZE); - writel(addr, base + OPB0_FSI_ADDR); - writel(0x1, base + OPB_IRQ_CLEAR); + writel_relaxed(CMD_READ, base + OPB0_RW); + writel_relaxed(transfer_size, base + OPB0_XFER_SIZE); + writel_relaxed(addr, base + OPB0_FSI_ADDR); + writel_relaxed(0x1, base + OPB_IRQ_CLEAR); writel(0x1, base + OPB_TRIGGER); ret = readl_poll_timeout(base + OPB_IRQ_STATUS, reg,
When setting up a read or write to the OPB memory space, we must perform five or six AHB writes. The ordering of these up until the trigger write does not matter, so use writel_relaxed. The generated code goes from (Debian GCC 10.2.1-6): mov r8, r3 mcr 15, 0, sl, cr7, cr10, {4} str sl, [r6, #20] mcr 15, 0, sl, cr7, cr10, {4} str r3, [r6, #24] mcr 15, 0, sl, cr7, cr10, {4} str r1, [r6, #28] mcr 15, 0, sl, cr7, cr10, {4} str r2, [r6, #32] mcr 15, 0, sl, cr7, cr10, {4} mov r1, #1 str r1, [r6, #64] ; 0x40 mcr 15, 0, sl, cr7, cr10, {4} str r1, [r6, #4] to this: str r3, [r7, #20] str r2, [r7, #24] str r1, [r7, #28] str r3, [r7, #64] mov r8, #0 mcr 15, 0, r8, cr7, cr10, {4} str r3, [r7, #4] Signed-off-by: Joel Stanley <joel@jms.id.au> --- drivers/fsi/fsi-master-aspeed.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-)