| Message ID | 20210409082522.625168-1-tudor.ambarus@microchip.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | pinctrl: at91-pio4: Fix slew rate disablement | expand |
On 09.04.2021 11:25, Tudor Ambarus wrote: > The slew rate was enabled by default for each configuration of the > pin. In case the pin had more than one configuration, even if > we set the slew rate as disabled in the device tree, the next pin > configuration would set again the slew rate enabled by default, > overwriting the slew rate disablement. > Instead of enabling the slew rate by default for each pin configuration, > enable the slew rate by default just once per pin, regardless of the > number of configurations. This way the slew rate disablement will also > work for cases where pins have multiple configurations. > > Fixes: 440b144978ba ("pinctrl: at91-pio4: add support for slew-rate") > Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> > --- > drivers/pinctrl/pinctrl-at91-pio4.c | 8 ++++---- > 1 file changed, 4 insertions(+), 4 deletions(-) > > diff --git a/drivers/pinctrl/pinctrl-at91-pio4.c b/drivers/pinctrl/pinctrl-at91-pio4.c > index a5d328808e4c..4c01d8471ffa 100644 > --- a/drivers/pinctrl/pinctrl-at91-pio4.c > +++ b/drivers/pinctrl/pinctrl-at91-pio4.c > @@ -801,6 +801,10 @@ static int atmel_conf_pin_config_group_set(struct pinctrl_dev *pctldev, > > conf = atmel_pin_config_read(pctldev, pin_id); > > + /* Keep slew rate enabled by default. */ > + if (atmel_pioctrl->slew_rate_support) > + conf |= ATMEL_PIO_SR_MASK; > + > for (i = 0; i < num_configs; i++) { > unsigned int param = pinconf_to_config_param(configs[i]); > unsigned int arg = pinconf_to_config_argument(configs[i]); > @@ -808,10 +812,6 @@ static int atmel_conf_pin_config_group_set(struct pinctrl_dev *pctldev, > dev_dbg(pctldev->dev, "%s: pin=%u, config=0x%lx\n", > __func__, pin_id, configs[i]); > > - /* Keep slew rate enabled by default. */ > - if (atmel_pioctrl->slew_rate_support) > - conf |= ATMEL_PIO_SR_MASK; > - > switch (param) { > case PIN_CONFIG_BIAS_DISABLE: > conf &= (~ATMEL_PIO_PUEN_MASK); >
On Fri, Apr 09, 2021 at 11:25:22AM +0300, Tudor Ambarus wrote: > The slew rate was enabled by default for each configuration of the > pin. In case the pin had more than one configuration, even if > we set the slew rate as disabled in the device tree, the next pin > configuration would set again the slew rate enabled by default, > overwriting the slew rate disablement. > Instead of enabling the slew rate by default for each pin configuration, > enable the slew rate by default just once per pin, regardless of the > number of configurations. This way the slew rate disablement will also > work for cases where pins have multiple configurations. > > Fixes: 440b144978ba ("pinctrl: at91-pio4: add support for slew-rate") > Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Thanks. > --- > drivers/pinctrl/pinctrl-at91-pio4.c | 8 ++++---- > 1 file changed, 4 insertions(+), 4 deletions(-) > > diff --git a/drivers/pinctrl/pinctrl-at91-pio4.c b/drivers/pinctrl/pinctrl-at91-pio4.c > index a5d328808e4c..4c01d8471ffa 100644 > --- a/drivers/pinctrl/pinctrl-at91-pio4.c > +++ b/drivers/pinctrl/pinctrl-at91-pio4.c > @@ -801,6 +801,10 @@ static int atmel_conf_pin_config_group_set(struct pinctrl_dev *pctldev, > > conf = atmel_pin_config_read(pctldev, pin_id); > > + /* Keep slew rate enabled by default. */ > + if (atmel_pioctrl->slew_rate_support) > + conf |= ATMEL_PIO_SR_MASK; > + > for (i = 0; i < num_configs; i++) { > unsigned int param = pinconf_to_config_param(configs[i]); > unsigned int arg = pinconf_to_config_argument(configs[i]); > @@ -808,10 +812,6 @@ static int atmel_conf_pin_config_group_set(struct pinctrl_dev *pctldev, > dev_dbg(pctldev->dev, "%s: pin=%u, config=0x%lx\n", > __func__, pin_id, configs[i]); > > - /* Keep slew rate enabled by default. */ > - if (atmel_pioctrl->slew_rate_support) > - conf |= ATMEL_PIO_SR_MASK; > - > switch (param) { > case PIN_CONFIG_BIAS_DISABLE: > conf &= (~ATMEL_PIO_PUEN_MASK); > -- > 2.25.1 >
On Fri, Apr 9, 2021 at 10:25 AM Tudor Ambarus <tudor.ambarus@microchip.com> wrote: > The slew rate was enabled by default for each configuration of the > pin. In case the pin had more than one configuration, even if > we set the slew rate as disabled in the device tree, the next pin > configuration would set again the slew rate enabled by default, > overwriting the slew rate disablement. > Instead of enabling the slew rate by default for each pin configuration, > enable the slew rate by default just once per pin, regardless of the > number of configurations. This way the slew rate disablement will also > work for cases where pins have multiple configurations. > > Fixes: 440b144978ba ("pinctrl: at91-pio4: add support for slew-rate") > Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Patch applied! Yours, Linus Walleij
diff --git a/drivers/pinctrl/pinctrl-at91-pio4.c b/drivers/pinctrl/pinctrl-at91-pio4.c index a5d328808e4c..4c01d8471ffa 100644 --- a/drivers/pinctrl/pinctrl-at91-pio4.c +++ b/drivers/pinctrl/pinctrl-at91-pio4.c @@ -801,6 +801,10 @@ static int atmel_conf_pin_config_group_set(struct pinctrl_dev *pctldev, conf = atmel_pin_config_read(pctldev, pin_id); + /* Keep slew rate enabled by default. */ + if (atmel_pioctrl->slew_rate_support) + conf |= ATMEL_PIO_SR_MASK; + for (i = 0; i < num_configs; i++) { unsigned int param = pinconf_to_config_param(configs[i]); unsigned int arg = pinconf_to_config_argument(configs[i]); @@ -808,10 +812,6 @@ static int atmel_conf_pin_config_group_set(struct pinctrl_dev *pctldev, dev_dbg(pctldev->dev, "%s: pin=%u, config=0x%lx\n", __func__, pin_id, configs[i]); - /* Keep slew rate enabled by default. */ - if (atmel_pioctrl->slew_rate_support) - conf |= ATMEL_PIO_SR_MASK; - switch (param) { case PIN_CONFIG_BIAS_DISABLE: conf &= (~ATMEL_PIO_PUEN_MASK);
The slew rate was enabled by default for each configuration of the pin. In case the pin had more than one configuration, even if we set the slew rate as disabled in the device tree, the next pin configuration would set again the slew rate enabled by default, overwriting the slew rate disablement. Instead of enabling the slew rate by default for each pin configuration, enable the slew rate by default just once per pin, regardless of the number of configurations. This way the slew rate disablement will also work for cases where pins have multiple configurations. Fixes: 440b144978ba ("pinctrl: at91-pio4: add support for slew-rate") Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> --- drivers/pinctrl/pinctrl-at91-pio4.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)