| Message ID | 20210517171205.1581938-2-abelvesa@kernel.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: dts: freescale: Add i.MX8DXL support | expand |
On Tue, May 18, 2021 at 1:14 AM <abelvesa@kernel.org> wrote: > > From: Jacky Bai <ping.bai@nxp.com> > > The i.MX8DXL is a device targeting the automotive and industrial > market segments. The flexibility of the architecture allows for > use in a wide variety of general embedded applications. The chip > is designed to achieve both high performance and low power consumption. > The chip relies on the power efficient dual (2x) Cortex-A35 cluster. > > Add the reserved memory node property for dsp reserved memory, > the wakeup-irq property for SCU node, the imx ion, the rpmsg and the > cm4 rproc support. > > Signed-off-by: Jacky Bai <ping.bai@nxp.com> > Signed-off-by: Abel Vesa <abel.vesa@nxp.com> FIrst of all, did you run make dt_binding_check? I wonder there're dt binding missing for a few nodes > --- > arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 286 +++++++++++++++++++++ > 1 file changed, 286 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi > > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > new file mode 100644 > index 000000000000..43e0bcdc2469 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > @@ -0,0 +1,286 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2019-2021 NXP > + */ > + > +#include <dt-bindings/clock/imx8-clock.h> > +#include <dt-bindings/firmware/imx/rsrc.h> > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/pinctrl/pads-imx8dxl.h> this depends on pinctrl driver. Is that upstreamed already? > +#include <dt-bindings/thermal/thermal.h> > + > +/ { > + interrupt-parent = <&gic>; > + #address-cells = <2>; > + #size-cells = <2>; > + > + aliases { > + ethernet0 = &fec1; > + ethernet1 = &eqos; > + gpio0 = &lsio_gpio0; > + gpio1 = &lsio_gpio1; > + gpio2 = &lsio_gpio2; > + gpio3 = &lsio_gpio3; > + gpio4 = &lsio_gpio4; > + gpio5 = &lsio_gpio5; > + gpio6 = &lsio_gpio6; > + gpio7 = &lsio_gpio7; > + i2c2 = &i2c2; > + i2c3 = &i2c3; > + mmc0 = &usdhc1; > + mmc1 = &usdhc2; > + mu1 = &lsio_mu1; > + serial0 = &lpuart0; > + serial1 = &lpuart1; > + serial2 = &lpuart2; > + serial3 = &lpuart3; > + }; > + > + cpus: cpus { > + #address-cells = <2>; > + #size-cells = <0>; > + > + /* We have 1 clusters with 2 Cortex-A35 cores */ > + A35_0: cpu@0 { > + device_type = "cpu"; > + compatible = "arm,cortex-a35"; > + reg = <0x0 0x0>; > + enable-method = "psci"; > + next-level-cache = <&A35_L2>; > + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; > + #cooling-cells = <2>; > + operating-points-v2 = <&a35_opp_table>; > + }; > + > + A35_1: cpu@1 { > + device_type = "cpu"; > + compatible = "arm,cortex-a35"; > + reg = <0x0 0x1>; > + enable-method = "psci"; > + next-level-cache = <&A35_L2>; > + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; > + #cooling-cells = <2>; > + operating-points-v2 = <&a35_opp_table>; > + }; > + > + A35_L2: l2-cache0 { > + compatible = "cache"; > + }; > + }; > + > + a35_opp_table: opp-table { > + compatible = "operating-points-v2"; > + opp-shared; > + > + opp-900000000 { > + opp-hz = /bits/ 64 <900000000>; > + opp-microvolt = <1000000>; > + clock-latency-ns = <150000>; > + }; > + > + opp-1200000000 { > + opp-hz = /bits/ 64 <1200000000>; > + opp-microvolt = <1100000>; > + clock-latency-ns = <150000>; > + opp-suspend; > + }; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + dsp_reserved: dsp@92400000 { > + reg = <0 0x92400000 0 0x2000000>; > + no-map; > + }; > + }; this could be added when enabling DSP in case any changes required in upstream > + > + rpmsg: rpmsg{ > + compatible = "fsl,imx8qxp-rpmsg"; I belive this is still not supported in upstream so drop it first > + /* up to now, the following channels are used in imx rpmsg > + * - tx1/rx1: messages channel. > + * - general interrupt1: remote proc finish re-init rpmsg stack > + * when A core is partition reset. > + */ > + mbox-names = "tx", "rx", "rxdb"; > + mboxes = <&lsio_mu5 0 1 > + &lsio_mu5 1 1 > + &lsio_mu5 3 1>; > + mub-partition = <3>; > + status = "disabled"; > + }; > + > + imx8dxl_cm4: imx8dxl_cm4@0 { > + compatible = "fsl,imx8qxp-cm4"; i'd suggest drop it first and add in separate patch as it's still not supported > + rsc-da = <0x90000000>; > + mbox-names = "tx", "rx", "rxdb"; > + mboxes = <&lsio_mu5 0 1 > + &lsio_mu5 1 1 > + &lsio_mu5 3 1>; > + mub-partition = <3>; > + core-index = <0>; > + core-id = <IMX_SC_R_M4_0_PID0>; > + status = "disabled"; > + power-domains = <&pd IMX_SC_R_M4_0_PID0>, > + <&pd IMX_SC_R_M4_0_MU_1A>; > + }; > + > + gic: interrupt-controller@51a00000 { > + compatible = "arm,gic-v3"; > + reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */ > + <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) */ > + #interrupt-cells = <3>; > + interrupt-controller; > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + pmu { > + compatible = "arm,armv8-pmuv3"; > + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + psci { > + compatible = "arm,psci-1.0"; > + method = "smc"; > + }; > + > + scu { > + compatible = "fsl,imx-scu"; > + mbox-names = "tx0", > + "rx0", > + "gip3"; > + mboxes = <&lsio_mu1 0 0 > + &lsio_mu1 1 0 > + &lsio_mu1 3 3>; > + > + pd: imx8dxl-pd { > + compatible = "fsl,imx8dxl-scu-pd", "fsl,scu-pd"; > + #power-domain-cells = <1>; > + wakeup-irq = <160 163 235 236 237 228 229 230 231 238 > + 239 240 166 169>; drop this property first which is still not supported > + }; > + > + clk: clock-controller { > + compatible = "fsl,imx8dxl-clk", "fsl,scu-clk"; > + #clock-cells = <2>; > + clocks = <&xtal32k &xtal24m>; > + clock-names = "xtal_32KHz", "xtal_24Mhz"; > + }; > + > + iomuxc: pinctrl { > + compatible = "fsl,imx8dxl-iomuxc"; make sure pinctrl upstreamed > + }; > + > + ocotp: imx8qx-ocotp { > + compatible = "fsl,imx8dxl-scu-ocotp", "fsl,imx8qxp-scu-ocotp"; need update binding doc as well > + #address-cells = <1>; > + #size-cells = <1>; > + > + fec_mac0: mac@2c4 { > + reg = <0x2c4 6>; > + }; > + > + fec_mac1: mac@2c6 { > + reg = <0x2c6 6>; > + }; > + }; > + > + rtc: rtc { > + compatible = "fsl,imx8dxl-sc-rtc", "fsl,imx8qxp-sc-rtc"; pls update dt binding as well > + }; > + > + watchdog { > + compatible = "fsl,imx-sc-wdt"; > + timeout-sec = <60>; > + }; > + > + tsens: thermal-sensor { > + compatible = "fsl,imx-sc-thermal"; > + #thermal-sensor-cells = <1>; > + }; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */ > + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */ > + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */ > + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */ > + }; > + > + thermal_zones: thermal-zones { > + cpu-thermal0 { > + polling-delay-passive = <250>; > + polling-delay = <2000>; > + thermal-sensors = <&tsens IMX_SC_R_SYSTEM>; > + > + trips { > + cpu_alert0: trip0 { > + temperature = <107000>; > + hysteresis = <2000>; > + type = "passive"; > + }; > + cpu_crit0: trip1 { > + temperature = <127000>; > + hysteresis = <2000>; > + type = "critical"; > + }; > + }; > + cooling-maps { > + map0 { > + trip = <&cpu_alert0>; > + cooling-device = > + <&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > + }; > + }; > + }; > + }; > + > + clk_dummy: clock-dummy { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <0>; > + clock-output-names = "clk_dummy"; > + }; > + > + xtal32k: clock-xtal32k { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <32768>; > + clock-output-names = "xtal_32KHz"; > + }; > + > + xtal24m: clock-xtal24m { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <24000000>; > + clock-output-names = "xtal_24MHz"; > + }; > + > + imx_ion { > + compatible = "fsl,mxc-ion"; drop this unsupported node Regards Aisheng > + fsl,heap-id = <0>; > + }; > + > + sc_pwrkey: sc-powerkey { > + compatible = "fsl,imx8-pwrkey"; > + linux,keycode = <KEY_POWER>; > + wakeup-source; > + }; > + > + /* sorted in register address */ > + #include "imx8-ss-adma.dtsi" > + #include "imx8-ss-conn.dtsi" > + #include "imx8-ss-ddr.dtsi" > + #include "imx8-ss-lsio.dtsi" > +}; > + > +#include "imx8dxl-ss-adma.dtsi" > +#include "imx8dxl-ss-conn.dtsi" > +#include "imx8dxl-ss-lsio.dtsi" > +#include "imx8dxl-ss-ddr.dtsi" > -- > 2.31.1 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On 21-05-18 15:35:41, Dong Aisheng wrote: > On Tue, May 18, 2021 at 1:14 AM <abelvesa@kernel.org> wrote: > > > > From: Jacky Bai <ping.bai@nxp.com> > > > > The i.MX8DXL is a device targeting the automotive and industrial > > market segments. The flexibility of the architecture allows for > > use in a wide variety of general embedded applications. The chip > > is designed to achieve both high performance and low power consumption. > > The chip relies on the power efficient dual (2x) Cortex-A35 cluster. > > > > Add the reserved memory node property for dsp reserved memory, > > the wakeup-irq property for SCU node, the imx ion, the rpmsg and the > > cm4 rproc support. > > > > Signed-off-by: Jacky Bai <ping.bai@nxp.com> > > Signed-off-by: Abel Vesa <abel.vesa@nxp.com> > > FIrst of all, did you run make dt_binding_check? > I wonder there're dt binding missing for a few nodes > Fixing those in the next version. > > --- > > arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 286 +++++++++++++++++++++ > > 1 file changed, 286 insertions(+) > > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > > new file mode 100644 > > index 000000000000..43e0bcdc2469 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi > > @@ -0,0 +1,286 @@ > > +// SPDX-License-Identifier: GPL-2.0+ > > +/* > > + * Copyright 2019-2021 NXP > > + */ > > + > > +#include <dt-bindings/clock/imx8-clock.h> > > +#include <dt-bindings/firmware/imx/rsrc.h> > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > +#include <dt-bindings/input/input.h> > > +#include <dt-bindings/pinctrl/pads-imx8dxl.h> > > this depends on pinctrl driver. Is that upstreamed already? > It is upstreamed. > > +#include <dt-bindings/thermal/thermal.h> > > + > > +/ { > > + interrupt-parent = <&gic>; > > + #address-cells = <2>; > > + #size-cells = <2>; > > + > > + aliases { > > + ethernet0 = &fec1; > > + ethernet1 = &eqos; > > + gpio0 = &lsio_gpio0; > > + gpio1 = &lsio_gpio1; > > + gpio2 = &lsio_gpio2; > > + gpio3 = &lsio_gpio3; > > + gpio4 = &lsio_gpio4; > > + gpio5 = &lsio_gpio5; > > + gpio6 = &lsio_gpio6; > > + gpio7 = &lsio_gpio7; > > + i2c2 = &i2c2; > > + i2c3 = &i2c3; > > + mmc0 = &usdhc1; > > + mmc1 = &usdhc2; > > + mu1 = &lsio_mu1; > > + serial0 = &lpuart0; > > + serial1 = &lpuart1; > > + serial2 = &lpuart2; > > + serial3 = &lpuart3; > > + }; > > + > > + cpus: cpus { > > + #address-cells = <2>; > > + #size-cells = <0>; > > + > > + /* We have 1 clusters with 2 Cortex-A35 cores */ > > + A35_0: cpu@0 { > > + device_type = "cpu"; > > + compatible = "arm,cortex-a35"; > > + reg = <0x0 0x0>; > > + enable-method = "psci"; > > + next-level-cache = <&A35_L2>; > > + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; > > + #cooling-cells = <2>; > > + operating-points-v2 = <&a35_opp_table>; > > + }; > > + > > + A35_1: cpu@1 { > > + device_type = "cpu"; > > + compatible = "arm,cortex-a35"; > > + reg = <0x0 0x1>; > > + enable-method = "psci"; > > + next-level-cache = <&A35_L2>; > > + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; > > + #cooling-cells = <2>; > > + operating-points-v2 = <&a35_opp_table>; > > + }; > > + > > + A35_L2: l2-cache0 { > > + compatible = "cache"; > > + }; > > + }; > > + > > + a35_opp_table: opp-table { > > + compatible = "operating-points-v2"; > > + opp-shared; > > + > > + opp-900000000 { > > + opp-hz = /bits/ 64 <900000000>; > > + opp-microvolt = <1000000>; > > + clock-latency-ns = <150000>; > > + }; > > + > > + opp-1200000000 { > > + opp-hz = /bits/ 64 <1200000000>; > > + opp-microvolt = <1100000>; > > + clock-latency-ns = <150000>; > > + opp-suspend; > > + }; > > + }; > > + > > + reserved-memory { > > + #address-cells = <2>; > > + #size-cells = <2>; > > + ranges; > > + > > + dsp_reserved: dsp@92400000 { > > + reg = <0 0x92400000 0 0x2000000>; > > + no-map; > > + }; > > + }; > > this could be added when enabling DSP in case any changes required in upstream > Unfortunately, the imx8-ss-adma already depends on it. So it needs to go in now, otherwise it won't build. > > + > > + rpmsg: rpmsg{ > > + compatible = "fsl,imx8qxp-rpmsg"; > > I belive this is still not supported in upstream > so drop it first > Removed in the next version. > > + /* up to now, the following channels are used in imx rpmsg > > + * - tx1/rx1: messages channel. > > + * - general interrupt1: remote proc finish re-init rpmsg stack > > + * when A core is partition reset. > > + */ > > + mbox-names = "tx", "rx", "rxdb"; > > + mboxes = <&lsio_mu5 0 1 > > + &lsio_mu5 1 1 > > + &lsio_mu5 3 1>; > > + mub-partition = <3>; > > + status = "disabled"; > > + }; > > + > > + imx8dxl_cm4: imx8dxl_cm4@0 { > > + compatible = "fsl,imx8qxp-cm4"; > > i'd suggest drop it first and add in separate patch > as it's still not supported > Removed in the next version. > > + rsc-da = <0x90000000>; > > + mbox-names = "tx", "rx", "rxdb"; > > + mboxes = <&lsio_mu5 0 1 > > + &lsio_mu5 1 1 > > + &lsio_mu5 3 1>; > > + mub-partition = <3>; > > + core-index = <0>; > > + core-id = <IMX_SC_R_M4_0_PID0>; > > + status = "disabled"; > > + power-domains = <&pd IMX_SC_R_M4_0_PID0>, > > + <&pd IMX_SC_R_M4_0_MU_1A>; > > + }; > > + > > + gic: interrupt-controller@51a00000 { > > + compatible = "arm,gic-v3"; > > + reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */ > > + <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) */ > > + #interrupt-cells = <3>; > > + interrupt-controller; > > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > > + }; > > + > > + pmu { > > + compatible = "arm,armv8-pmuv3"; > > + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; > > + }; > > + > > + psci { > > + compatible = "arm,psci-1.0"; > > + method = "smc"; > > + }; > > + > > + scu { > > + compatible = "fsl,imx-scu"; > > + mbox-names = "tx0", > > + "rx0", > > + "gip3"; > > + mboxes = <&lsio_mu1 0 0 > > + &lsio_mu1 1 0 > > + &lsio_mu1 3 3>; > > + > > + pd: imx8dxl-pd { > > + compatible = "fsl,imx8dxl-scu-pd", "fsl,scu-pd"; > > + #power-domain-cells = <1>; > > + wakeup-irq = <160 163 235 236 237 228 229 230 231 238 > > + 239 240 166 169>; > > drop this property first which is still not supported > Removed in the next version. > > + }; > > + > > + clk: clock-controller { > > + compatible = "fsl,imx8dxl-clk", "fsl,scu-clk"; > > + #clock-cells = <2>; > > + clocks = <&xtal32k &xtal24m>; > > + clock-names = "xtal_32KHz", "xtal_24Mhz"; > > + }; > > + > > + iomuxc: pinctrl { > > + compatible = "fsl,imx8dxl-iomuxc"; > > make sure pinctrl upstreamed > It is upstreamed. > > + }; > > + > > + ocotp: imx8qx-ocotp { > > + compatible = "fsl,imx8dxl-scu-ocotp", "fsl,imx8qxp-scu-ocotp"; > > need update binding doc as well > Will do in the next version. > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + fec_mac0: mac@2c4 { > > + reg = <0x2c4 6>; > > + }; > > + > > + fec_mac1: mac@2c6 { > > + reg = <0x2c6 6>; > > + }; > > + }; > > + > > + rtc: rtc { > > + compatible = "fsl,imx8dxl-sc-rtc", "fsl,imx8qxp-sc-rtc"; > > pls update dt binding as well > I'll actually remove this in the next version. Will be sent later on as a separate patch. > > + }; > > + > > + watchdog { > > + compatible = "fsl,imx-sc-wdt"; > > + timeout-sec = <60>; > > + }; > > + > > + tsens: thermal-sensor { > > + compatible = "fsl,imx-sc-thermal"; > > + #thermal-sensor-cells = <1>; > > + }; > > + }; > > + > > + timer { > > + compatible = "arm,armv8-timer"; > > + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */ > > + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */ > > + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */ > > + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */ > > + }; > > + > > + thermal_zones: thermal-zones { > > + cpu-thermal0 { > > + polling-delay-passive = <250>; > > + polling-delay = <2000>; > > + thermal-sensors = <&tsens IMX_SC_R_SYSTEM>; > > + > > + trips { > > + cpu_alert0: trip0 { > > + temperature = <107000>; > > + hysteresis = <2000>; > > + type = "passive"; > > + }; > > + cpu_crit0: trip1 { > > + temperature = <127000>; > > + hysteresis = <2000>; > > + type = "critical"; > > + }; > > + }; > > + cooling-maps { > > + map0 { > > + trip = <&cpu_alert0>; > > + cooling-device = > > + <&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > > + <&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > > + }; > > + }; > > + }; > > + }; > > + > > + clk_dummy: clock-dummy { > > + compatible = "fixed-clock"; > > + #clock-cells = <0>; > > + clock-frequency = <0>; > > + clock-output-names = "clk_dummy"; > > + }; > > + > > + xtal32k: clock-xtal32k { > > + compatible = "fixed-clock"; > > + #clock-cells = <0>; > > + clock-frequency = <32768>; > > + clock-output-names = "xtal_32KHz"; > > + }; > > + > > + xtal24m: clock-xtal24m { > > + compatible = "fixed-clock"; > > + #clock-cells = <0>; > > + clock-frequency = <24000000>; > > + clock-output-names = "xtal_24MHz"; > > + }; > > + > > + imx_ion { > > + compatible = "fsl,mxc-ion"; > > drop this unsupported node > Removed in the next version. > Regards > Aisheng > > > + fsl,heap-id = <0>; > > + }; > > + > > + sc_pwrkey: sc-powerkey { > > + compatible = "fsl,imx8-pwrkey"; > > + linux,keycode = <KEY_POWER>; > > + wakeup-source; > > + }; > > + > > + /* sorted in register address */ > > + #include "imx8-ss-adma.dtsi" > > + #include "imx8-ss-conn.dtsi" > > + #include "imx8-ss-ddr.dtsi" > > + #include "imx8-ss-lsio.dtsi" > > +}; > > + > > +#include "imx8dxl-ss-adma.dtsi" > > +#include "imx8dxl-ss-conn.dtsi" > > +#include "imx8dxl-ss-lsio.dtsi" > > +#include "imx8dxl-ss-ddr.dtsi" > > -- > > 2.31.1 > > > > > > _______________________________________________ > > linux-arm-kernel mailing list > > linux-arm-kernel@lists.infradead.org > > https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Flists.infradead.org%2Fmailman%2Flistinfo%2Flinux-arm-kernel&data=04%7C01%7Cabel.vesa%40nxp.com%7C843de7d5f11f49ba992408d919cfafdc%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637569202065001061%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=ZmB%2FXRdAz3Y0q2FFu2C2Y6cqYbfDQkk7Q1SNqESO2zc%3D&reserved=0
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi new file mode 100644 index 000000000000..43e0bcdc2469 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi @@ -0,0 +1,286 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019-2021 NXP + */ + +#include <dt-bindings/clock/imx8-clock.h> +#include <dt-bindings/firmware/imx/rsrc.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/pads-imx8dxl.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + ethernet0 = &fec1; + ethernet1 = &eqos; + gpio0 = &lsio_gpio0; + gpio1 = &lsio_gpio1; + gpio2 = &lsio_gpio2; + gpio3 = &lsio_gpio3; + gpio4 = &lsio_gpio4; + gpio5 = &lsio_gpio5; + gpio6 = &lsio_gpio6; + gpio7 = &lsio_gpio7; + i2c2 = &i2c2; + i2c3 = &i2c3; + mmc0 = &usdhc1; + mmc1 = &usdhc2; + mu1 = &lsio_mu1; + serial0 = &lpuart0; + serial1 = &lpuart1; + serial2 = &lpuart2; + serial3 = &lpuart3; + }; + + cpus: cpus { + #address-cells = <2>; + #size-cells = <0>; + + /* We have 1 clusters with 2 Cortex-A35 cores */ + A35_0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a35"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&A35_L2>; + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; + #cooling-cells = <2>; + operating-points-v2 = <&a35_opp_table>; + }; + + A35_1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a35"; + reg = <0x0 0x1>; + enable-method = "psci"; + next-level-cache = <&A35_L2>; + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; + #cooling-cells = <2>; + operating-points-v2 = <&a35_opp_table>; + }; + + A35_L2: l2-cache0 { + compatible = "cache"; + }; + }; + + a35_opp_table: opp-table { + compatible = "operating-points-v2"; + opp-shared; + + opp-900000000 { + opp-hz = /bits/ 64 <900000000>; + opp-microvolt = <1000000>; + clock-latency-ns = <150000>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <1100000>; + clock-latency-ns = <150000>; + opp-suspend; + }; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + dsp_reserved: dsp@92400000 { + reg = <0 0x92400000 0 0x2000000>; + no-map; + }; + }; + + rpmsg: rpmsg{ + compatible = "fsl,imx8qxp-rpmsg"; + /* up to now, the following channels are used in imx rpmsg + * - tx1/rx1: messages channel. + * - general interrupt1: remote proc finish re-init rpmsg stack + * when A core is partition reset. + */ + mbox-names = "tx", "rx", "rxdb"; + mboxes = <&lsio_mu5 0 1 + &lsio_mu5 1 1 + &lsio_mu5 3 1>; + mub-partition = <3>; + status = "disabled"; + }; + + imx8dxl_cm4: imx8dxl_cm4@0 { + compatible = "fsl,imx8qxp-cm4"; + rsc-da = <0x90000000>; + mbox-names = "tx", "rx", "rxdb"; + mboxes = <&lsio_mu5 0 1 + &lsio_mu5 1 1 + &lsio_mu5 3 1>; + mub-partition = <3>; + core-index = <0>; + core-id = <IMX_SC_R_M4_0_PID0>; + status = "disabled"; + power-domains = <&pd IMX_SC_R_M4_0_PID0>, + <&pd IMX_SC_R_M4_0_MU_1A>; + }; + + gic: interrupt-controller@51a00000 { + compatible = "arm,gic-v3"; + reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */ + <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) */ + #interrupt-cells = <3>; + interrupt-controller; + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + scu { + compatible = "fsl,imx-scu"; + mbox-names = "tx0", + "rx0", + "gip3"; + mboxes = <&lsio_mu1 0 0 + &lsio_mu1 1 0 + &lsio_mu1 3 3>; + + pd: imx8dxl-pd { + compatible = "fsl,imx8dxl-scu-pd", "fsl,scu-pd"; + #power-domain-cells = <1>; + wakeup-irq = <160 163 235 236 237 228 229 230 231 238 + 239 240 166 169>; + }; + + clk: clock-controller { + compatible = "fsl,imx8dxl-clk", "fsl,scu-clk"; + #clock-cells = <2>; + clocks = <&xtal32k &xtal24m>; + clock-names = "xtal_32KHz", "xtal_24Mhz"; + }; + + iomuxc: pinctrl { + compatible = "fsl,imx8dxl-iomuxc"; + }; + + ocotp: imx8qx-ocotp { + compatible = "fsl,imx8dxl-scu-ocotp", "fsl,imx8qxp-scu-ocotp"; + #address-cells = <1>; + #size-cells = <1>; + + fec_mac0: mac@2c4 { + reg = <0x2c4 6>; + }; + + fec_mac1: mac@2c6 { + reg = <0x2c6 6>; + }; + }; + + rtc: rtc { + compatible = "fsl,imx8dxl-sc-rtc", "fsl,imx8qxp-sc-rtc"; + }; + + watchdog { + compatible = "fsl,imx-sc-wdt"; + timeout-sec = <60>; + }; + + tsens: thermal-sensor { + compatible = "fsl,imx-sc-thermal"; + #thermal-sensor-cells = <1>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */ + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */ + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */ + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */ + }; + + thermal_zones: thermal-zones { + cpu-thermal0 { + polling-delay-passive = <250>; + polling-delay = <2000>; + thermal-sensors = <&tsens IMX_SC_R_SYSTEM>; + + trips { + cpu_alert0: trip0 { + temperature = <107000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu_crit0: trip1 { + temperature = <127000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + }; + + clk_dummy: clock-dummy { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "clk_dummy"; + }; + + xtal32k: clock-xtal32k { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "xtal_32KHz"; + }; + + xtal24m: clock-xtal24m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + clock-output-names = "xtal_24MHz"; + }; + + imx_ion { + compatible = "fsl,mxc-ion"; + fsl,heap-id = <0>; + }; + + sc_pwrkey: sc-powerkey { + compatible = "fsl,imx8-pwrkey"; + linux,keycode = <KEY_POWER>; + wakeup-source; + }; + + /* sorted in register address */ + #include "imx8-ss-adma.dtsi" + #include "imx8-ss-conn.dtsi" + #include "imx8-ss-ddr.dtsi" + #include "imx8-ss-lsio.dtsi" +}; + +#include "imx8dxl-ss-adma.dtsi" +#include "imx8dxl-ss-conn.dtsi" +#include "imx8dxl-ss-lsio.dtsi" +#include "imx8dxl-ss-ddr.dtsi"