new file mode 100644
@@ -0,0 +1,174 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/nxp,imx8mq-mipi-csi2.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX8MQ MIPI CSI-2 receiver
+
+maintainers:
+ - Martin Kepplinger <martin.kepplinger@puri.sm>
+
+description: |-
+ This binding covers the CSI-2 RX PHY and host controller included in the
+ NXP i.MX8MQ SoC. It handles the sensor/image input and process for all the
+ input imaging devices.
+
+properties:
+ compatible:
+ enum:
+ - fsl,imx8mq-mipi-csi2
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: core is the RX Controller Core Clock input. This clock
+ must be exactly equal to or faster than the receive
+ byteclock from the RX DPHY.
+ - description: esc is the Rx Escape Clock. This must be the same escape
+ clock that the RX DPHY receives.
+ - description: ui is the pixel clock (phy_ref up to 333Mhz).
+ See the reference manual for details.
+
+ clock-names:
+ items:
+ - const: core
+ - const: esc
+ - const: ui
+
+ power-domains:
+ maxItems: 1
+
+ resets:
+ items:
+ - description: CORE_RESET reset register bit definition
+ - description: PHY_REF_RESET reset register bit definition
+ - description: ESC_RESET reset register bit definition
+
+ fsl,mipi-phy-gpr:
+ description: |
+ The phandle to the imx8mq syscon iomux-gpr with the register
+ for setting RX_ENABLE for the mipi receiver.
+
+ The format should be as follows:
+ <gpr req_gpr>
+ gpr is the phandle to general purpose register node.
+ req_gpr is the gpr register offset of RX_ENABLE for the mipi phy.
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ items:
+ items:
+ - description: The 'gpr' is the phandle to general purpose register node.
+ - description: The 'req_gpr' is the gpr register offset containing
+ CSI2_1_RX_ENABLE or CSI2_2_RX_ENABLE respectively.
+ maximum: 0xff
+
+ interconnects:
+ maxItems: 1
+
+ interconnect-names:
+ const: dram
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ Input port node, single endpoint describing the CSI-2 transmitter.
+
+ properties:
+ endpoint:
+ $ref: video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ data-lanes:
+ items:
+ minItems: 1
+ maxItems: 4
+ items:
+ - const: 1
+ - const: 2
+ - const: 3
+ - const: 4
+
+ required:
+ - data-lanes
+
+ port@1:
+ $ref: /schemas/graph.yaml#/properties/port
+ description:
+ Output port node
+
+ required:
+ - port@0
+ - port@1
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - power-domains
+ - resets
+ - fsl,mipi-phy-gpr
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/imx8mq-clock.h>
+ #include <dt-bindings/interconnect/imx8mq.h>
+ #include <dt-bindings/reset/imx8mq-reset.h>
+
+ csi@30a70000 {
+ compatible = "fsl,imx8mq-mipi-csi2";
+ reg = <0x30a70000 0x1000>;
+ clocks = <&clk IMX8MQ_CLK_CSI1_CORE>,
+ <&clk IMX8MQ_CLK_CSI1_ESC>,
+ <&clk IMX8MQ_CLK_CSI1_PHY_REF>;
+ clock-names = "core", "esc", "ui";
+ assigned-clocks = <&clk IMX8MQ_CLK_CSI1_CORE>,
+ <&clk IMX8MQ_CLK_CSI1_PHY_REF>,
+ <&clk IMX8MQ_CLK_CSI1_ESC>;
+ assigned-clock-rates = <266000000>, <200000000>, <66000000>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>,
+ <&clk IMX8MQ_SYS2_PLL_1000M>,
+ <&clk IMX8MQ_SYS1_PLL_800M>;
+ power-domains = <&pgc_mipi_csi1>;
+ resets = <&src IMX8MQ_RESET_MIPI_CSI1_CORE_RESET>,
+ <&src IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET>,
+ <&src IMX8MQ_RESET_MIPI_CSI1_ESC_RESET>;
+ fsl,mipi-phy-gpr = <&iomuxc_gpr 0x88>;
+ interconnects = <&noc IMX8MQ_ICM_CSI1 &noc IMX8MQ_ICS_DRAM>;
+ interconnect-names = "dram";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ imx8mm_mipi_csi_in: endpoint {
+ remote-endpoint = <&imx477_out>;
+ data-lanes = <1 2 3 4>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ imx8mm_mipi_csi_out: endpoint {
+ remote-endpoint = <&csi_in>;
+ };
+ };
+ };
+ };
+
+...