@@ -15,6 +15,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8910.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a3u-eur.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a5u-eur.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-serranove.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8992-bullhead-rev-101.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8992-msft-lumia-octagon-talkman.dtb
new file mode 100644
@@ -0,0 +1,301 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2019 Stephan Gerhold
+
+/dts-v1/;
+
+#include "msm8916-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/*
+ * NOTE: The original firmware from Samsung can only boot ARM32 kernels.
+ * Unfortunately, the firmware is signed and cannot be replaced easily.
+ * There seems to be no way to boot ARM64 kernels on this device at the moment,
+ * even though the hardware would support it.
+ *
+ * However, it is possible to use this device tree by compiling an ARM32 kernel
+ * instead. For clarity and build testing this device tree is maintained next
+ * to the other MSM8916 device trees. However, it is actually used through
+ * arch/arm/boot/dts/qcom-msm8916-samsung-serranove.dts
+ */
+
+/ {
+ model = "Samsung Galaxy S4 Mini Value Edition";
+ compatible = "samsung,serranove", "qcom,msm8916";
+
+ aliases {
+ serial0 = &blsp1_uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0";
+ };
+
+ reserved-memory {
+ /* Additional memory used by Samsung firmware modifications */
+ tz-apps@85500000 {
+ reg = <0x0 0x85500000 0x0 0xb00000>;
+ no-map;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_default>;
+
+ label = "GPIO Buttons";
+
+ volume-up {
+ label = "Volume Up";
+ gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ home {
+ label = "Home";
+ gpios = <&msmgpio 109 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOMEPAGE>;
+ };
+ };
+
+ gpio-hall-sensor {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_hall_sensor_default>;
+
+ label = "GPIO Hall Effect Sensor";
+
+ hall-sensor {
+ label = "Hall Effect Sensor";
+ gpios = <&msmgpio 52 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ linux,can-disable;
+ };
+ };
+
+ i2c-muic {
+ compatible = "i2c-gpio";
+ sda-gpios = <&msmgpio 105 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&msmgpio 106 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&muic_i2c_default>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ muic: extcon@14 {
+ compatible = "siliconmitus,sm5504-muic";
+ reg = <0x14>;
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&muic_irq_default>;
+ };
+ };
+};
+
+&blsp1_uart2 {
+ status = "okay";
+};
+
+&pm8916_resin {
+ status = "okay";
+ linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&pm8916_vib {
+ status = "okay";
+};
+
+&pronto {
+ status = "okay";
+
+ iris {
+ compatible = "qcom,wcn3660b";
+ };
+};
+
+&sdhc_1 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+ pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
+ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
+
+ non-removable;
+
+ /*
+ * FIXME: Disable UHS-I modes since tuning fails with:
+ *
+ * sdhci_msm 7864900.sdhci: mmc1: No tuning point found
+ * mmc1: tuning execution failed: -5
+ * mmc1: error -5 whilst initialising SD card
+ *
+ * This is the quirk used on downstream, which suggests this is
+ * a hardware limitation. However, probing a card using DDR50
+ * (without tuning), so maybe only tuning is broken?
+ */
+ no-1-8-v;
+};
+
+&usb {
+ status = "okay";
+ extcon = <&muic>, <&muic>;
+};
+
+&usb_hs_phy {
+ extcon = <&muic>;
+};
+
+&smd_rpm_regulators {
+ vdd_l1_l2_l3-supply = <&pm8916_s3>;
+ vdd_l4_l5_l6-supply = <&pm8916_s4>;
+ vdd_l7-supply = <&pm8916_s4>;
+
+ s3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2100000>;
+ };
+
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l4 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l8 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l10 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ l11 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-allow-set-load;
+ regulator-system-load = <200000>;
+ };
+
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ l13 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+};
+
+&msmgpio {
+ gpio_keys_default: gpio-keys-default {
+ pins = "gpio107", "gpio109";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ gpio_hall_sensor_default: gpio-hall-sensor-default {
+ pins = "gpio52";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ muic_i2c_default: muic-i2c-default {
+ pins = "gpio105", "gpio106";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ muic_irq_default: muic-irq-default {
+ pins = "gpio12";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
The Samsung Galaxy S4 Mini Value Edition is an updated version of the original S4 Mini based on MSM8916. It is similar to the other Samsung devices based on MSM8916 with only a few minor differences. The device tree contains initial support for the S4 Mini Value Edition with: - UART - eMMC/SD card (needs quirk for some reason) - Buttons - Vibrator - WiFi/Bluetooth (WCNSS) - USB Unfortunately, the S4 Mini VE was released with outdated 32-bit only firmware and never received any update from Samsung. Since the 32-bit TrustZone firmware is signed there seems to be no way currently to actually boot this device tree on arm64 Linux at the moment. :( However, it is possible to use this device tree by compiling an ARM32 kernel instead. The device tree can be easily built on ARM32 with an #include and it works really well there. To avoid confusion for others it is still better to add this device tree on arm64. Otherwise it's easy to forget to update this one when making some changes that affect all MSM8916 devices. Maybe someone finds a way to boot ARM64 Linux on this device at some point. In this case I expect that this device tree can be simply used as-is. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../dts/qcom/msm8916-samsung-serranove.dts | 301 ++++++++++++++++++ 2 files changed, 302 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts