@@ -62,6 +62,40 @@ reg_aud_1v8: regulator-audio-1v8 {
enable-active-high;
};
+ /*
+ * the pinctrl for reg_csi_1v8 and reg_vcam_1v8 is added to the PMIC
+ * since we can't have it twice in the 2 different regulator nodes.
+ */
+ reg_csi_1v8: regulator-csi-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "CAMERA_VDDIO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <®_vdd_3v3>;
+ gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ /* controlled by the CAMERA_POWER_KEY HKS */
+ reg_vcam_1v2: regulator-vcam-1v2 {
+ compatible = "regulator-fixed";
+ regulator-name = "CAMERA_VDDD_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <®_vdd_1v8>;
+ enable-active-high;
+ };
+
+ reg_vcam_2v8: regulator-vcam-2v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "CAMERA_VDDA_2V8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ vin-supply = <®_vdd_3v3>;
+ gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
reg_gnss: regulator-gnss {
compatible = "regulator-fixed";
pinctrl-names = "default";
@@ -329,6 +363,20 @@ MX8MQ_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x83
>;
};
+ pinctrl_camera_pwr: camerapwrgrp {
+ fsl,pins = <
+ /* CAMERA_PWR_EN_3V3 */
+ MX8MQ_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x83
+ >;
+ };
+
+ pinctrl_csi1: csi1grp {
+ fsl,pins = <
+ /* CSI1_NRST */
+ MX8MQ_IOMUXC_ENET_RXC_GPIO1_IO25 0x83
+ >;
+ };
+
pinctrl_charger_in: chargeringrp {
fsl,pins = <
/* CHRG_INT */
@@ -725,7 +773,7 @@ pmic: pmic@4b {
compatible = "rohm,bd71837";
reg = <0x4b>;
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pmic>;
+ pinctrl-0 = <&pinctrl_pmic>, <&pinctrl_camera_pwr>;
clocks = <&pmic_osc>;
clock-names = "osc";
clock-output-names = "pmic_clk";
CAMERA_PWR_EN controls two different power supplies that cameras will use. The hardware killswitch controls a third one. Describe that appropriately. The pinctrl that describes the gpio that is used in 2 places here is added to the pmic. This is done because pmic is powered early enough to make sure this will work. When we would have put the same pinctrl property into the 2 regulator nodes (instead of the pmic), we'd get: imx8mq-pinctrl 30330000.pinctrl: pin MX8MQ_IOMUXC_GPIO1_IO00 already requested by regulator-csi-1v8; cannot claim for regulator-vcam-2v8 imx8mq-pinctrl 30330000.pinctrl: pin-10 (regulator-vcam-2v8) status -22 imx8mq-pinctrl 30330000.pinctrl: could not request pin 10 (MX8MQ_IOMUXC_GPIO1_IO00) from group camerapwrgrp on device 30330000.pinctrl Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> --- .../boot/dts/freescale/imx8mq-librem5.dtsi | 50 ++++++++++++++++++- 1 file changed, 49 insertions(+), 1 deletion(-)