@@ -40,6 +40,33 @@
#define ETH_FINE_DLY_GTXC BIT(1)
#define ETH_FINE_DLY_RXC BIT(0)
+/* Peri Configuration register for mt8195 */
+#define MT8195_PERI_ETH_CTRL0 0xFD0
+#define MT8195_RMII_CLK_SRC_INTERNAL BIT(28)
+#define MT8195_RMII_CLK_SRC_RXC BIT(27)
+#define MT8195_ETH_INTF_SEL GENMASK(26, 24)
+#define MT8195_RGMII_TXC_PHASE_CTRL BIT(22)
+#define MT8195_EXT_PHY_MODE BIT(21)
+#define MT8195_DLY_GTXC_INV BIT(12)
+#define MT8195_DLY_GTXC_ENABLE BIT(5)
+#define MT8195_DLY_GTXC_STAGES GENMASK(4, 0)
+
+#define MT8195_PERI_ETH_CTRL1 0xFD4
+#define MT8195_DLY_RXC_INV BIT(25)
+#define MT8195_DLY_RXC_ENABLE BIT(18)
+#define MT8195_DLY_RXC_STAGES GENMASK(17, 13)
+#define MT8195_DLY_TXC_INV BIT(12)
+#define MT8195_DLY_TXC_ENABLE BIT(5)
+#define MT8195_DLY_TXC_STAGES GENMASK(4, 0)
+
+#define MT8195_PERI_ETH_CTRL2 0xFD8
+#define MT8195_DLY_RMII_RXC_INV BIT(25)
+#define MT8195_DLY_RMII_RXC_ENABLE BIT(18)
+#define MT8195_DLY_RMII_RXC_STAGES GENMASK(17, 13)
+#define MT8195_DLY_RMII_TXC_INV BIT(12)
+#define MT8195_DLY_RMII_TXC_ENABLE BIT(5)
+#define MT8195_DLY_RMII_TXC_STAGES GENMASK(4, 0)
+
struct mac_delay_struct {
u32 tx_delay;
u32 rx_delay;
@@ -58,11 +85,13 @@ struct mediatek_dwmac_plat_data {
int num_clks_to_config;
bool rmii_clk_from_mac;
bool rmii_rxc;
+ bool mac_wol;
};
struct mediatek_dwmac_variant {
int (*dwmac_set_phy_interface)(struct mediatek_dwmac_plat_data *plat);
int (*dwmac_set_delay)(struct mediatek_dwmac_plat_data *plat);
+ void (*dwmac_fix_mac_speed)(void *priv, unsigned int speed);
/* clock ids to be requested */
const char * const *clk_list;
@@ -78,6 +107,10 @@ static const char * const mt2712_dwmac_clk_l[] = {
"axi", "apb", "mac_main", "ptp_ref", "rmii_internal"
};
+static const char * const mt8195_dwmac_clk_l[] = {
+ "axi", "apb", "mac_cg", "mac_main", "ptp_ref", "rmii_internal"
+};
+
static int mt2712_set_interface(struct mediatek_dwmac_plat_data *plat)
{
int rmii_clk_from_mac = plat->rmii_clk_from_mac ? RMII_CLK_SRC_INTERNAL : 0;
@@ -268,6 +301,204 @@ static const struct mediatek_dwmac_variant mt2712_gmac_variant = {
.tx_delay_max = 17600,
};
+static int mt8195_set_interface(struct mediatek_dwmac_plat_data *plat)
+{
+ int rmii_clk_from_mac = plat->rmii_clk_from_mac ? MT8195_RMII_CLK_SRC_INTERNAL : 0;
+ int rmii_rxc = plat->rmii_rxc ? MT8195_RMII_CLK_SRC_RXC : 0;
+ u32 intf_val = 0;
+
+ /* The clock labeled as "rmii_internal" in mt8195_dwmac_clk_l is needed
+ * only in RMII(when MAC provides the reference clock), and useless for
+ * RGMII/MII/RMII(when PHY provides the reference clock).
+ * num_clks_to_config indicates the real number of clocks should be
+ * configured, equals to (plat->variant->num_clks - 1) in default for all the case,
+ * then +1 for rmii_clk_from_mac case.
+ */
+ plat->num_clks_to_config = plat->variant->num_clks - 1;
+
+ /* select phy interface in top control domain */
+ switch (plat->phy_mode) {
+ case PHY_INTERFACE_MODE_MII:
+ intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL, PHY_INTF_MII);
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ if (plat->rmii_clk_from_mac)
+ plat->num_clks_to_config++;
+ intf_val |= (rmii_rxc | rmii_clk_from_mac);
+ intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL, PHY_INTF_RMII);
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL, PHY_INTF_RGMII);
+ break;
+ default:
+ dev_err(plat->dev, "phy interface not supported\n");
+ return -EINVAL;
+ }
+
+ /* MT8195 only support external PHY */
+ intf_val |= MT8195_EXT_PHY_MODE;
+
+ regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL0, intf_val);
+
+ return 0;
+}
+
+static void mt8195_delay_ps2stage(struct mediatek_dwmac_plat_data *plat)
+{
+ struct mac_delay_struct *mac_delay = &plat->mac_delay;
+
+ /* 290ps per stage */
+ mac_delay->tx_delay /= 290;
+ mac_delay->rx_delay /= 290;
+}
+
+static void mt8195_delay_stage2ps(struct mediatek_dwmac_plat_data *plat)
+{
+ struct mac_delay_struct *mac_delay = &plat->mac_delay;
+
+ /* 290ps per stage */
+ mac_delay->tx_delay *= 290;
+ mac_delay->rx_delay *= 290;
+}
+
+static int mt8195_set_delay(struct mediatek_dwmac_plat_data *plat)
+{
+ struct mac_delay_struct *mac_delay = &plat->mac_delay;
+ u32 gtxc_delay_val, delay_val = 0, rmii_delay_val = 0;
+
+ mt8195_delay_ps2stage(plat);
+
+ switch (plat->phy_mode) {
+ case PHY_INTERFACE_MODE_MII:
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_ENABLE, !!mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_STAGES, mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_INV, mac_delay->tx_inv);
+
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV, mac_delay->rx_inv);
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ if (plat->rmii_clk_from_mac) {
+ /* case 1: mac provides the rmii reference clock,
+ * and the clock output to TXC pin.
+ * The egress timing can be adjusted by RMII_TXC delay macro circuit.
+ * The ingress timing can be adjusted by RMII_RXC delay macro circuit.
+ */
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_TXC_ENABLE,
+ !!mac_delay->tx_delay);
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_TXC_STAGES,
+ mac_delay->tx_delay);
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_TXC_INV,
+ mac_delay->tx_inv);
+
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_RXC_ENABLE,
+ !!mac_delay->rx_delay);
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_RXC_STAGES,
+ mac_delay->rx_delay);
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_RXC_INV,
+ mac_delay->rx_inv);
+ } else {
+ /* case 2: the rmii reference clock is from external phy,
+ * and the property "rmii_rxc" indicates which pin(TXC/RXC)
+ * the reference clk is connected to. The reference clock is a
+ * received signal, so rx_delay/rx_inv are used to indicate
+ * the reference clock timing adjustment
+ */
+ if (plat->rmii_rxc) {
+ /* the rmii reference clock from outside is connected
+ * to RXC pin, the reference clock will be adjusted
+ * by RXC delay macro circuit.
+ */
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE,
+ !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES,
+ mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV,
+ mac_delay->rx_inv);
+ } else {
+ /* the rmii reference clock from outside is connected
+ * to TXC pin, the reference clock will be adjusted
+ * by TXC delay macro circuit.
+ */
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_ENABLE,
+ !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_STAGES,
+ mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_INV,
+ mac_delay->rx_inv);
+ }
+ }
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_ENABLE, !!mac_delay->tx_delay);
+ gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_STAGES, mac_delay->tx_delay);
+ gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_INV, mac_delay->tx_inv);
+
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV, mac_delay->rx_inv);
+
+ break;
+ default:
+ dev_err(plat->dev, "phy interface not supported\n");
+ return -EINVAL;
+ }
+
+ regmap_update_bits(plat->peri_regmap,
+ MT8195_PERI_ETH_CTRL0,
+ MT8195_RGMII_TXC_PHASE_CTRL |
+ MT8195_DLY_GTXC_INV |
+ MT8195_DLY_GTXC_ENABLE |
+ MT8195_DLY_GTXC_STAGES,
+ gtxc_delay_val);
+ regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL1, delay_val);
+ regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL2, rmii_delay_val);
+
+ mt8195_delay_stage2ps(plat);
+
+ return 0;
+}
+
+static void mt8195_fix_mac_speed(void *priv, unsigned int speed)
+{
+ struct mediatek_dwmac_plat_data *priv_plat = priv;
+
+ if ((phy_interface_mode_is_rgmii(priv_plat->phy_mode))) {
+ /* prefer 2ns fixed delay which is controlled by TXC_PHASE_CTRL,
+ * when link speed is 1Gbps with RGMII interface,
+ * Fall back to delay macro circuit for 10/100Mbps link speed.
+ */
+ if (speed == SPEED_1000)
+ regmap_update_bits(priv_plat->peri_regmap,
+ MT8195_PERI_ETH_CTRL0,
+ MT8195_RGMII_TXC_PHASE_CTRL |
+ MT8195_DLY_GTXC_ENABLE |
+ MT8195_DLY_GTXC_INV |
+ MT8195_DLY_GTXC_STAGES,
+ MT8195_RGMII_TXC_PHASE_CTRL);
+ else
+ mt8195_set_delay(priv_plat);
+ }
+}
+
+static const struct mediatek_dwmac_variant mt8195_gmac_variant = {
+ .dwmac_set_phy_interface = mt8195_set_interface,
+ .dwmac_set_delay = mt8195_set_delay,
+ .dwmac_fix_mac_speed = mt8195_fix_mac_speed,
+ .clk_list = mt8195_dwmac_clk_l,
+ .num_clks = ARRAY_SIZE(mt8195_dwmac_clk_l),
+ .dma_bit_mask = 35,
+ .rx_delay_max = 9280,
+ .tx_delay_max = 9280,
+};
+
static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
{
struct mac_delay_struct *mac_delay = &plat->mac_delay;
@@ -308,6 +539,7 @@ static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
mac_delay->rx_inv = of_property_read_bool(plat->np, "mediatek,rxc-inverse");
plat->rmii_rxc = of_property_read_bool(plat->np, "mediatek,rmii-rxc");
plat->rmii_clk_from_mac = of_property_read_bool(plat->np, "mediatek,rmii-clk-from-mac");
+ plat->mac_wol = of_property_read_bool(plat->np, "mediatek,mac-wol");
return 0;
}
@@ -384,6 +616,7 @@ static int mediatek_dwmac_clks_config(void *priv, bool enabled)
return ret;
}
+
static int mediatek_dwmac_probe(struct platform_device *pdev)
{
struct mediatek_dwmac_plat_data *priv_plat;
@@ -421,7 +654,7 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
return PTR_ERR(plat_dat);
plat_dat->interface = priv_plat->phy_mode;
- plat_dat->use_phy_wol = 1;
+ plat_dat->use_phy_wol = priv_plat->mac_wol ? 0 : 1;
plat_dat->riwt_off = 1;
plat_dat->maxmtu = ETH_DATA_LEN;
plat_dat->addr64 = priv_plat->variant->dma_bit_mask;
@@ -429,7 +662,23 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
plat_dat->init = mediatek_dwmac_init;
plat_dat->exit = mediatek_dwmac_exit;
plat_dat->clks_config = mediatek_dwmac_clks_config;
+ if (priv_plat->variant->dwmac_fix_mac_speed)
+ plat_dat->fix_mac_speed = priv_plat->variant->dwmac_fix_mac_speed;
+ plat_dat->safety_feat_cfg = devm_kzalloc(&pdev->dev,
+ sizeof(*plat_dat->safety_feat_cfg),
+ GFP_KERNEL);
+ if (!plat_dat->safety_feat_cfg)
+ return -ENOMEM;
+ plat_dat->safety_feat_cfg->tsoee = 1;
+ plat_dat->safety_feat_cfg->mrxpee = 0;
+ plat_dat->safety_feat_cfg->mestee = 1;
+ plat_dat->safety_feat_cfg->mrxee = 1;
+ plat_dat->safety_feat_cfg->mtxee = 1;
+ plat_dat->safety_feat_cfg->epsi = 0;
+ plat_dat->safety_feat_cfg->edpp = 1;
+ plat_dat->safety_feat_cfg->prtyen = 1;
+ plat_dat->safety_feat_cfg->tmouten = 1;
mediatek_dwmac_init(pdev, priv_plat);
ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
@@ -444,6 +693,8 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
static const struct of_device_id mediatek_dwmac_match[] = {
{ .compatible = "mediatek,mt2712-gmac",
.data = &mt2712_gmac_variant },
+ { .compatible = "mediatek,mt8195-gmac",
+ .data = &mt8195_gmac_variant },
{ }
};
Add Ethernet support for MediaTek SoCs from the mt8195 family. Signed-off-by: Biao Huang <biao.huang@mediatek.com> --- .../ethernet/stmicro/stmmac/dwmac-mediatek.c | 253 +++++++++++++++++- 1 file changed, 252 insertions(+), 1 deletion(-)