@@ -11,6 +11,18 @@
#include <linux/platform_device.h>
#include <linux/regulator/consumer.h>
+/* USB glue registers */
+#define USB_CTRL0 0x00
+#define USB_CTRL1 0x04
+
+#define USB_CTRL0_PORTPWR_EN BIT(12) /* 1 - PPC enabled (default) */
+#define USB_CTRL0_USB3_FIXED BIT(22) /* 1 - USB3 permanent attached */
+#define USB_CTRL0_USB2_FIXED BIT(23) /* 1 - USB2 permanent attached */
+
+#define USB_CTRL1_OC_POLARITY BIT(16) /* 0 - HIGH / 1 - LOW */
+#define USB_CTRL1_PWR_POLARITY BIT(17) /* 0 - HIGH / 1 - LOW */
+
+/* USB phy registers */
#define PHY_CTRL0 0x0
#define PHY_CTRL0_REF_SSP_EN BIT(2)
#define PHY_CTRL0_FSEL_MASK GENMASK(10, 5)
@@ -35,9 +47,46 @@ struct imx8mq_usb_phy {
struct phy *phy;
struct clk *clk;
void __iomem *base;
+ void __iomem *glue_base;
struct regulator *vbus;
};
+static void imx8mp_configure_glue(struct imx8mq_usb_phy *dwc3_imx)
+{
+ struct device *dev = &dwc3_imx->phy->dev;
+ u32 value;
+
+ if (!dwc3_imx->glue_base)
+ return;
+
+ value = readl(dwc3_imx->glue_base + USB_CTRL0);
+
+ if (device_property_read_bool(dev, "fsl,permanently-attached"))
+ value |= (USB_CTRL0_USB2_FIXED | USB_CTRL0_USB3_FIXED);
+ else
+ value &= ~(USB_CTRL0_USB2_FIXED | USB_CTRL0_USB3_FIXED);
+
+ if (device_property_read_bool(dev, "fsl,disable-port-power-control"))
+ value &= ~(USB_CTRL0_PORTPWR_EN);
+ else
+ value |= USB_CTRL0_PORTPWR_EN;
+
+ writel(value, dwc3_imx->glue_base + USB_CTRL0);
+
+ value = readl(dwc3_imx->glue_base + USB_CTRL1);
+ if (device_property_read_bool(dev, "fsl,over-current-active-low"))
+ value |= USB_CTRL1_OC_POLARITY;
+ else
+ value &= ~USB_CTRL1_OC_POLARITY;
+
+ if (device_property_read_bool(dev, "fsl,power-active-low"))
+ value |= USB_CTRL1_PWR_POLARITY;
+ else
+ value &= ~USB_CTRL1_PWR_POLARITY;
+
+ writel(value, dwc3_imx->glue_base + USB_CTRL1);
+}
+
static int imx8mq_usb_phy_init(struct phy *phy)
{
struct imx8mq_usb_phy *imx_phy = phy_get_drvdata(phy);
@@ -69,6 +118,8 @@ static int imx8mp_usb_phy_init(struct phy *phy)
struct imx8mq_usb_phy *imx_phy = phy_get_drvdata(phy);
u32 value;
+ imx8mp_configure_glue(imx_phy);
+
/* USB3.0 PHY signal fsel for 24M ref */
value = readl(imx_phy->base + PHY_CTRL0);
value &= ~PHY_CTRL0_FSEL_MASK;
@@ -153,6 +204,7 @@ static int imx8mq_usb_phy_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct imx8mq_usb_phy *imx_phy;
const struct phy_ops *phy_ops;
+ struct resource *res;
imx_phy = devm_kzalloc(dev, sizeof(*imx_phy), GFP_KERNEL);
if (!imx_phy)
@@ -168,6 +220,15 @@ static int imx8mq_usb_phy_probe(struct platform_device *pdev)
if (IS_ERR(imx_phy->base))
return PTR_ERR(imx_phy->base);
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!res) {
+ dev_warn(dev, "Base address for glue layer missing. Continuing without, some features are missing though.");
+ } else {
+ imx_phy->glue_base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(imx_phy->glue_base))
+ return PTR_ERR(imx_phy->glue_base);
+ }
+
phy_ops = of_device_get_match_data(dev);
if (!phy_ops)
return -EINVAL;
The i.MX8MP glue layer has support for the following flags: * over-current polarity * PWR pad polarity * controlling PPC flag in HCCPARAMS register * parmanent port attach for usb2 & usb3 port Allow setting these flags by supporting specific flags in the glue node. In order to get this to work an additional IORESOURCE_MEM is necessary actually pointing to the glue layer. For backward compatibility this is purely optional. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> --- drivers/phy/freescale/phy-fsl-imx8mq-usb.c | 61 ++++++++++++++++++++++ 1 file changed, 61 insertions(+)