@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
- * Copyright 2014-2020 Toradex
+ * Copyright 2014-2022 Toradex
* Copyright 2012 Freescale Semiconductor, Inc.
* Copyright 2011 Linaro Ltd.
*/
@@ -58,53 +58,6 @@
wakeup-source;
};
};
-
- lcd_display: disp0 {
- compatible = "fsl,imx-parallel-display";
- #address-cells = <1>;
- #size-cells = <0>;
- interface-pix-fmt = "bgr666";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ipu1_lcdif>;
- status = "okay";
-
- port@0 {
- reg = <0>;
-
- lcd_display_in: endpoint {
- remote-endpoint = <&ipu1_di0_disp0>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- lcd_display_out: endpoint {
- remote-endpoint = <&lcd_panel_in>;
- };
- };
- };
-
- panel: panel {
- /*
- * edt,et057090dhu: EDT 5.7" LCD TFT
- * edt,et070080dh6: EDT 7.0" LCD TFT
- */
- compatible = "edt,et057090dhu";
- backlight = <&backlight>;
-
- port {
- lcd_panel_in: endpoint {
- remote-endpoint = <&lcd_display_out>;
- };
- };
- };
-};
-
-&backlight {
- brightness-levels = <0 127 191 223 239 247 251 255>;
- default-brightness-level = <1>;
- status = "okay";
};
/* Colibri SSP */
@@ -122,10 +75,6 @@
};
};
-&hdmi {
- status = "okay";
-};
-
/*
* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board)
*/
@@ -178,10 +127,6 @@
};
};
-&ipu1_di0_disp0 {
- remote-endpoint = <&lcd_display_in>;
-};
-
&pwm1 {
status = "okay";
};
@@ -13,13 +13,59 @@
backlight: backlight {
compatible = "pwm-backlight";
+ brightness-levels = <0 127 191 223 239 247 251 255>;
+ default-brightness-level = <1>;
+ enable-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* Colibri BL_ON */
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio_bl_on>;
+ power-supply = <®_module_3v3>;
pwms = <&pwm3 0 5000000>;
- enable-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* Colibri BL_ON */
status = "disabled";
};
+ lcd_display: disp0 {
+ compatible = "fsl,imx-parallel-display";
+ interface-pix-fmt = "bgr666";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_lcdif>;
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ lcd_display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lcd_display_out: endpoint {
+ remote-endpoint = <&lcd_panel_in>;
+ };
+ };
+ };
+
+ panel_dpi: panel-dpi {
+ /*
+ * edt,et057090dhu: EDT 5.7" LCD TFT
+ * edt,et070080dh6: EDT 7.0" LCD TFT
+ */
+ compatible = "edt,et057090dhu";
+ backlight = <&backlight>;
+ status = "disabled";
+
+ port {
+ lcd_panel_in: endpoint {
+ remote-endpoint = <&lcd_display_out>;
+ };
+ };
+ };
+
reg_module_3v3: regulator-module-3v3 {
compatible = "regulator-fixed";
regulator-name = "+V3.3";
@@ -476,7 +522,7 @@
/* ADC converstion time: 80 clocks */
st,sample-time = <4>;
- stmpe_touchscreen {
+ stmpe_ts: stmpe_touchscreen {
compatible = "st,stmpe-ts";
/* 8 sample average control */
st,ave-ctrl = <3>;
@@ -491,9 +537,10 @@
st,settling = <3>;
/* 5 ms touch detect interrupt delay */
st,touch-det-delay = <5>;
+ status = "disabled";
};
- stmpe_adc {
+ stmpe_adc: stmpe_adc {
compatible = "st,stmpe-adc";
/* forbid to use ADC channels 3-0 (touch) */
st,norequest-mask = <0x0F>;
@@ -514,6 +561,10 @@
status = "disabled";
};
+&ipu1_di0_disp0 {
+ remote-endpoint = <&lcd_display_in>;
+};
+
/* Colibri PWM<B> */
&pwm1 {
pinctrl-names = "default";
The Toradex Colibri family is composed of SoM that can be plugged in various carrier board, with carrier boards allowing multiple optional add-on (e.g. display, camera, ...). Keep all the SoM specific part into the module .dtsi, disabling everything that is not self-contained on the board. The carrier board dts can reuse/enable anything that is defined in the module dtsi. Additional device tree overlays can be used for any accessories that are plugged in the carrier board. Disable parallel RGB: The parallel RGB interface (lcd_display) and all related nodes can be enabled in an overlay if used. Keep all nodes disabled in the module-level device tree. Rename display interface node to match imx6qdl-apalis to make it easier to use overlays. The pwm-backlight binding now requires the power-supply property, add it. Disable stmpe touchscreen: The touchscreen can be enabled in an overlay if used. Add labels to the stmpe sub nodes. Disable hdmi interface: HDMI can be enabled in an overlay if used. Update SPDX-License spelling to latest convention. Update Copyright year. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> --- arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts | 59 +------------------- arch/arm/boot/dts/imx6qdl-colibri.dtsi | 57 ++++++++++++++++++- 2 files changed, 56 insertions(+), 60 deletions(-)