diff mbox series

[v2,09/14] ARM: dts: imx6dl-colibri: Move common nodes to SoM dtsi

Message ID 20220411152234.12678-10-max.oss.09@gmail.com (mailing list archive)
State New, archived
Headers show
Series ARM: dts: imx6dl-colibri: Misc improvements and newly added carriers | expand

Commit Message

Max Krummenacher April 11, 2022, 3:22 p.m. UTC 
From: Max Krummenacher <max.krummenacher@toradex.com>

The following two nodes define module level functionality, move
them from the carrier board dts file to the SoM file.
While at it, reorder the properties in the gpio-keys node alphabetical.

- gpio-keys defining the wakeup pin
- memory node

The atmel touchscreen node can be used on any carrier board.
Move it from the carrier board to the module-level device tree and
keep it disabled.
Set the default pinmuxing to the dedicated connector available
on newer carrier boards and rename the pinctrl labels specifying
the INT/Reset signal to a common pattern.
  pinctrl_atmel_conn - uses 107/106 pins as used on dedicated connector
  pinctrl_atmel_adap - uses 28/30 pins as used with jumper wires

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
---

(no changes since v1)

 arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts | 49 ------------------
 arch/arm/boot/dts/imx6qdl-colibri.dtsi       | 53 ++++++++++++++++++++
 2 files changed, 53 insertions(+), 49 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
index 535b5c156229..dff2d35e693b 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
@@ -17,12 +17,6 @@ 
 	compatible = "toradex,colibri_imx6dl-eval-v3", "toradex,colibri_imx6dl",
 		     "fsl,imx6dl";
 
-	/* Will be filled by the bootloader */
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0>;
-	};
-
 	aliases {
 		i2c0 = &i2c2;
 		i2c1 = &i2c3;
@@ -44,20 +38,6 @@ 
 		clock-frequency = <16000000>;
 		clock-output-names = "clk16m";
 	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
 };
 
 /* Colibri SSP */
@@ -81,21 +61,6 @@ 
 &i2c3 {
 	status = "okay";
 
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pcap_1>;
-		reg = <0x4a>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 */
-		reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;	/* SODIMM 30 */
-		status = "disabled";
-	};
-
 	/* M41T0M6 real time clock on carrier board */
 	rtc_i2c: rtc@68 {
 		compatible = "st,m41t0";
@@ -111,20 +76,6 @@ 
 		&pinctrl_weim_gpio_5 &pinctrl_weim_gpio_6
 		&pinctrl_usbh_oc_1 &pinctrl_usbc_id_1
 	>;
-
-	pinctrl_pcap_1: pcap1grp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_9__GPIO1_IO09	0x1b0b0 /* SODIMM 28 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10	0x1b0b0 /* SODIMM 30 */
-		>;
-	};
-
-	pinctrl_mxt_ts: mxttsgrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_CS1__GPIO2_IO24	0x130b0 /* SODIMM 107 */
-			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14	0x130b0 /* SODIMM 106 */
-		>;
-	};
 };
 
 &pwm1 {
diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
index 3459bfb5c60b..1c49fd3e6286 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -23,6 +23,20 @@ 
 		status = "disabled";
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
 	lcd_display: disp0 {
 		compatible = "fsl,imx-parallel-display";
 		interface-pix-fmt = "bgr666";
@@ -50,6 +64,12 @@ 
 		};
 	};
 
+	/* Will be filled by the bootloader */
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0>;
+	};
+
 	panel_dpi: panel-dpi {
 		/*
 		 * edt,et057090dhu: EDT 5.7" LCD TFT
@@ -564,6 +584,17 @@ 
 	scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "disabled";
+
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		interrupt-parent = <&gpio2>;
+		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;	/* SODIMM 107 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_atmel_conn>;
+		reg = <0x4a>;
+		reset-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;	/* SODIMM 106 */
+		status = "disabled";
+	};
 };
 
 &ipu1_di0_disp0 {
@@ -682,6 +713,28 @@ 
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbh_oc_1>;
 
+	/* Atmel MXT touchsceen + Capacitive Touch Adapter */
+	/* NOTE: This pin group conflicts with pin groups
+	 * pinctrl_pwm1/pinctrl_pwm4. Don't use them simultaneously.
+	 */
+	pinctrl_atmel_adap: atmeladaptergrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09   0xb0b1  /* SODIMM  28 */
+			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0xb0b1  /* SODIMM  30 */
+		>;
+	};
+
+	/* Atmel MXT touchsceen + boards with built-in Capacitive Touch Connector */
+	/* NOTE: This pin group conflicts with pin groups pinctrl_weim_cs1 and
+	 * pinctrl_weim_cs2. Don't use them simultaneously.
+	 */
+	pinctrl_atmel_conn: atmelconnectorgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24  0xb0b1  /* SODIMM_107 */
+			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0xb0b1  /* SODIMM_106 */
+		>;
+	};
+
 	pinctrl_audmux: audmuxgrp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_COL0__AUD5_TXC	0x130b0