@@ -849,17 +849,13 @@ static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
static int brcm_pcie_setup(struct brcm_pcie *pcie)
{
- struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
u64 rc_bar2_offset, rc_bar2_size;
void __iomem *base = pcie->base;
- struct device *dev = pcie->dev;
+ struct pci_host_bridge *bridge;
struct resource_entry *entry;
- bool ssc_good = false;
- struct resource *res;
- int num_out_wins = 0;
- u16 nlw, cls, lnksta;
- int i, ret, memc;
u32 tmp, burst, aspm_support;
+ int num_out_wins = 0;
+ int ret, memc;
/* Reset the bridge */
pcie->bridge_sw_init_set(pcie, 1);
@@ -935,6 +931,11 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
else
pcie->msi_target_addr = BRCM_MSI_TARGET_ADDR_GT_4GB;
+ if (!brcm_pcie_rc_mode(pcie)) {
+ dev_err(pcie->dev, "PCIe RC controller misconfigured as Endpoint\n");
+ return -EINVAL;
+ }
+
/* disable the PCIe->GISB memory window (RC_BAR1) */
tmp = readl(base + PCIE_MISC_RC_BAR1_CONFIG_LO);
tmp &= ~PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK;
@@ -945,31 +946,27 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
tmp &= ~PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK;
writel(tmp, base + PCIE_MISC_RC_BAR3_CONFIG_LO);
- if (pcie->gen)
- brcm_pcie_set_gen(pcie, pcie->gen);
-
- /* Unassert the fundamental reset */
- pcie->perst_set(pcie, 0);
+ /* Don't advertise L0s capability if 'aspm-no-l0s' */
+ aspm_support = PCIE_LINK_STATE_L1;
+ if (!of_property_read_bool(pcie->np, "aspm-no-l0s"))
+ aspm_support |= PCIE_LINK_STATE_L0S;
+ tmp = readl(base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
+ u32p_replace_bits(&tmp, aspm_support,
+ PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_ASPM_SUPPORT_MASK);
+ writel(tmp, base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
/*
- * Give the RC/EP time to wake up, before trying to configure RC.
- * Intermittently check status for link-up, up to a total of 100ms.
+ * For config space accesses on the RC, show the right class for
+ * a PCIe-PCIe bridge (the default setting is to be EP mode).
*/
- for (i = 0; i < 100 && !brcm_pcie_link_up(pcie); i += 5)
- msleep(5);
-
- if (!brcm_pcie_link_up(pcie)) {
- dev_err(dev, "link down\n");
- return -ENODEV;
- }
-
- if (!brcm_pcie_rc_mode(pcie)) {
- dev_err(dev, "PCIe misconfigured; is in EP mode\n");
- return -EINVAL;
- }
+ tmp = readl(base + PCIE_RC_CFG_PRIV1_ID_VAL3);
+ u32p_replace_bits(&tmp, 0x060400,
+ PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK);
+ writel(tmp, base + PCIE_RC_CFG_PRIV1_ID_VAL3);
+ bridge = pci_host_bridge_from_priv(pcie);
resource_list_for_each_entry(entry, &bridge->windows) {
- res = entry->res;
+ struct resource *res = entry->res;
if (resource_type(res) != IORESOURCE_MEM)
continue;
@@ -998,23 +995,41 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
num_out_wins++;
}
- /* Don't advertise L0s capability if 'aspm-no-l0s' */
- aspm_support = PCIE_LINK_STATE_L1;
- if (!of_property_read_bool(pcie->np, "aspm-no-l0s"))
- aspm_support |= PCIE_LINK_STATE_L0S;
- tmp = readl(base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
- u32p_replace_bits(&tmp, aspm_support,
- PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_ASPM_SUPPORT_MASK);
- writel(tmp, base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
+ /* PCIe->SCB endian mode for BAR */
+ tmp = readl(base + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1);
+ u32p_replace_bits(&tmp, PCIE_RC_CFG_VENDOR_SPCIFIC_REG1_LITTLE_ENDIAN,
+ PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK);
+ writel(tmp, base + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1);
+
+ return 0;
+}
+
+static int brcm_pcie_start_link(struct brcm_pcie *pcie)
+{
+ struct device *dev = pcie->dev;
+ void __iomem *base = pcie->base;
+ u16 nlw, cls, lnksta;
+ bool ssc_good = false;
+ u32 tmp;
+ int ret, i;
+
+ /* Unassert the fundamental reset */
+ pcie->perst_set(pcie, 0);
/*
- * For config space accesses on the RC, show the right class for
- * a PCIe-PCIe bridge (the default setting is to be EP mode).
+ * Give the RC/EP time to wake up, before trying to configure RC.
+ * Intermittently check status for link-up, up to a total of 100ms.
*/
- tmp = readl(base + PCIE_RC_CFG_PRIV1_ID_VAL3);
- u32p_replace_bits(&tmp, 0x060400,
- PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK);
- writel(tmp, base + PCIE_RC_CFG_PRIV1_ID_VAL3);
+ for (i = 0; i < 100 && !brcm_pcie_link_up(pcie); i += 5)
+ msleep(5);
+
+ if (!brcm_pcie_link_up(pcie)) {
+ dev_err(dev, "link down\n");
+ return -ENODEV;
+ }
+
+ if (pcie->gen)
+ brcm_pcie_set_gen(pcie, pcie->gen);
if (pcie->ssc) {
ret = brcm_pcie_set_ssc(pcie);
@@ -1031,12 +1046,6 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
pci_speed_string(pcie_link_speed[cls]), nlw,
ssc_good ? "(SSC)" : "(!SSC)");
- /* PCIe->SCB endian mode for BAR */
- tmp = readl(base + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1);
- u32p_replace_bits(&tmp, PCIE_RC_CFG_VENDOR_SPCIFIC_REG1_LITTLE_ENDIAN,
- PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK);
- writel(tmp, base + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1);
-
/*
* Refclk from RC should be gated with CLKREQ# input when ASPM L0s,L1
* is enabled => setting the CLKREQ_DEBUG_ENABLE field to 1.
@@ -1204,6 +1213,10 @@ static int brcm_pcie_resume(struct device *dev)
if (ret)
goto err_reset;
+ ret = brcm_pcie_start_link(pcie);
+ if (ret)
+ goto err_reset;
+
if (pcie->msi)
brcm_msi_set_regs(pcie->msi);
@@ -1393,6 +1406,10 @@ static int brcm_pcie_probe(struct platform_device *pdev)
if (ret)
goto fail;
+ ret = brcm_pcie_start_link(pcie);
+ if (ret)
+ goto fail;
+
pcie->hw_rev = readl(pcie->base + PCIE_MISC_REVISION);
if (pcie->type == BCM4908 && pcie->hw_rev >= BRCM_PCIE_HW_REV_3_20) {
dev_err(pcie->dev, "hardware revision with unsupported PERST# setup\n");
Currently, the function does the setup for establishing PCIe link-up with the downstream device, and it does the actual link-up as well. The calling sequence is (roughly) the following in the probe: -> brcm_pcie_probe() -> brcm_pcie_setup(); /* Set-up and link-up */ -> pci_host_probe(bridge); This commit splits the setup function in two: brcm_pcie_setup(), which only does the set-up, and brcm_pcie_start_link(), which only does the link-up. The reason why we are doing this is to lay a foundation for subsequent commits so that we can turn on any power regulators, as described in the root port's DT node, prior to doing link-up. We do this by defining an add_bus() callback which is invoked during enumeration. At the end of this patchset the probe function trace will look something like this: -> brcm_pcie_probe() -> brcm_pcie_setup(); /* Set-up only */ -> pci_host_probe(bridge); -> [enumeration] -> pci_alloc_child_bus() -> bus->ops->add_bus(bus); /* We've set this op */ -> brcm_pcie_add_bus() /* Our callback */ -> [turn on regulators] /* Main objective! */ -> brcm_pcie_start_link() /* Link-up */ One final note: some code that was executed after the PCIe linkup is now placed so that it executes prior to linkup, since this code has to run prior to the invocation of pci_host_probe(). Link: https://lore.kernel.org/r/20220106160332.2143-5-jim2101024@gmail.com Signed-off-by: Jim Quinlan <jim2101024@gmail.com> --- drivers/pci/controller/pcie-brcmstb.c | 111 +++++++++++++++----------- 1 file changed, 64 insertions(+), 47 deletions(-)