| Message ID | 20220915150959.3646702-1-han.xu@nxp.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v2] clk: imx: imx6sx: remove the SET_RATE_PARENT flag for QSPI clocks | expand |
On Thu, Sep 15, 2022 at 12:10 PM Han Xu <han.xu@nxp.com> wrote: > > There is no dedicate parent clock for QSPI so SET_RATE_PARENT flag > should not be used. For instance, the default parent clock for QSPI is > pll2_bus, which is also the parent clock for quite a few modules, such > as MMDC, once GPMI NAND set clock rate for EDO5 mode can cause system > hang due to pll2_bus rate changed. > > Fixes: f1541e15e38e ("clk: imx6sx: Switch to clk_hw based API") > Signed-off-by: Han Xu <han.xu@nxp.com> Tested-by: Fabio Estevam <festevam@denx.de>
On 22-09-15 10:09:59, Han Xu wrote: > There is no dedicate parent clock for QSPI so SET_RATE_PARENT flag > should not be used. For instance, the default parent clock for QSPI is > pll2_bus, which is also the parent clock for quite a few modules, such > as MMDC, once GPMI NAND set clock rate for EDO5 mode can cause system > hang due to pll2_bus rate changed. > > Fixes: f1541e15e38e ("clk: imx6sx: Switch to clk_hw based API") > Signed-off-by: Han Xu <han.xu@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Stephen, will you be picking this? Thanks. > > --- > changes in v2 > - fix the build break due to missing close parenthesis > --- > drivers/clk/imx/clk-imx6sx.c | 4 ++-- > 1 file changed, 2 insertions(+), 2 deletions(-) > > diff --git a/drivers/clk/imx/clk-imx6sx.c b/drivers/clk/imx/clk-imx6sx.c > index 2301d8fb8c76..d9ff831bdf47 100644 > --- a/drivers/clk/imx/clk-imx6sx.c > +++ b/drivers/clk/imx/clk-imx6sx.c > @@ -324,13 +324,13 @@ static void __init imx6sx_clocks_init(struct device_node *ccm_node) > hws[IMX6SX_CLK_SSI3_SEL] = imx_clk_hw_mux("ssi3_sel", base + 0x1c, 14, 2, ssi_sels, ARRAY_SIZE(ssi_sels)); > hws[IMX6SX_CLK_SSI2_SEL] = imx_clk_hw_mux("ssi2_sel", base + 0x1c, 12, 2, ssi_sels, ARRAY_SIZE(ssi_sels)); > hws[IMX6SX_CLK_SSI1_SEL] = imx_clk_hw_mux("ssi1_sel", base + 0x1c, 10, 2, ssi_sels, ARRAY_SIZE(ssi_sels)); > - hws[IMX6SX_CLK_QSPI1_SEL] = imx_clk_hw_mux_flags("qspi1_sel", base + 0x1c, 7, 3, qspi1_sels, ARRAY_SIZE(qspi1_sels), CLK_SET_RATE_PARENT); > + hws[IMX6SX_CLK_QSPI1_SEL] = imx_clk_hw_mux("qspi1_sel", base + 0x1c, 7, 3, qspi1_sels, ARRAY_SIZE(qspi1_sels)); > hws[IMX6SX_CLK_PERCLK_SEL] = imx_clk_hw_mux("perclk_sel", base + 0x1c, 6, 1, perclk_sels, ARRAY_SIZE(perclk_sels)); > hws[IMX6SX_CLK_VID_SEL] = imx_clk_hw_mux("vid_sel", base + 0x20, 21, 3, vid_sels, ARRAY_SIZE(vid_sels)); > hws[IMX6SX_CLK_ESAI_SEL] = imx_clk_hw_mux("esai_sel", base + 0x20, 19, 2, audio_sels, ARRAY_SIZE(audio_sels)); > hws[IMX6SX_CLK_CAN_SEL] = imx_clk_hw_mux("can_sel", base + 0x20, 8, 2, can_sels, ARRAY_SIZE(can_sels)); > hws[IMX6SX_CLK_UART_SEL] = imx_clk_hw_mux("uart_sel", base + 0x24, 6, 1, uart_sels, ARRAY_SIZE(uart_sels)); > - hws[IMX6SX_CLK_QSPI2_SEL] = imx_clk_hw_mux_flags("qspi2_sel", base + 0x2c, 15, 3, qspi2_sels, ARRAY_SIZE(qspi2_sels), CLK_SET_RATE_PARENT); > + hws[IMX6SX_CLK_QSPI2_SEL] = imx_clk_hw_mux("qspi2_sel", base + 0x2c, 15, 3, qspi2_sels, ARRAY_SIZE(qspi2_sels)); > hws[IMX6SX_CLK_SPDIF_SEL] = imx_clk_hw_mux("spdif_sel", base + 0x30, 20, 2, audio_sels, ARRAY_SIZE(audio_sels)); > hws[IMX6SX_CLK_AUDIO_SEL] = imx_clk_hw_mux("audio_sel", base + 0x30, 7, 2, audio_sels, ARRAY_SIZE(audio_sels)); > hws[IMX6SX_CLK_ENET_PRE_SEL] = imx_clk_hw_mux("enet_pre_sel", base + 0x34, 15, 3, enet_pre_sels, ARRAY_SIZE(enet_pre_sels)); > -- > 2.25.1 >
Quoting Han Xu (2022-09-15 08:09:59) > There is no dedicate parent clock for QSPI so SET_RATE_PARENT flag > should not be used. For instance, the default parent clock for QSPI is > pll2_bus, which is also the parent clock for quite a few modules, such > as MMDC, once GPMI NAND set clock rate for EDO5 mode can cause system > hang due to pll2_bus rate changed. > > Fixes: f1541e15e38e ("clk: imx6sx: Switch to clk_hw based API") > Signed-off-by: Han Xu <han.xu@nxp.com> > > --- Applied to clk-fixes
diff --git a/drivers/clk/imx/clk-imx6sx.c b/drivers/clk/imx/clk-imx6sx.c index 2301d8fb8c76..d9ff831bdf47 100644 --- a/drivers/clk/imx/clk-imx6sx.c +++ b/drivers/clk/imx/clk-imx6sx.c @@ -324,13 +324,13 @@ static void __init imx6sx_clocks_init(struct device_node *ccm_node) hws[IMX6SX_CLK_SSI3_SEL] = imx_clk_hw_mux("ssi3_sel", base + 0x1c, 14, 2, ssi_sels, ARRAY_SIZE(ssi_sels)); hws[IMX6SX_CLK_SSI2_SEL] = imx_clk_hw_mux("ssi2_sel", base + 0x1c, 12, 2, ssi_sels, ARRAY_SIZE(ssi_sels)); hws[IMX6SX_CLK_SSI1_SEL] = imx_clk_hw_mux("ssi1_sel", base + 0x1c, 10, 2, ssi_sels, ARRAY_SIZE(ssi_sels)); - hws[IMX6SX_CLK_QSPI1_SEL] = imx_clk_hw_mux_flags("qspi1_sel", base + 0x1c, 7, 3, qspi1_sels, ARRAY_SIZE(qspi1_sels), CLK_SET_RATE_PARENT); + hws[IMX6SX_CLK_QSPI1_SEL] = imx_clk_hw_mux("qspi1_sel", base + 0x1c, 7, 3, qspi1_sels, ARRAY_SIZE(qspi1_sels)); hws[IMX6SX_CLK_PERCLK_SEL] = imx_clk_hw_mux("perclk_sel", base + 0x1c, 6, 1, perclk_sels, ARRAY_SIZE(perclk_sels)); hws[IMX6SX_CLK_VID_SEL] = imx_clk_hw_mux("vid_sel", base + 0x20, 21, 3, vid_sels, ARRAY_SIZE(vid_sels)); hws[IMX6SX_CLK_ESAI_SEL] = imx_clk_hw_mux("esai_sel", base + 0x20, 19, 2, audio_sels, ARRAY_SIZE(audio_sels)); hws[IMX6SX_CLK_CAN_SEL] = imx_clk_hw_mux("can_sel", base + 0x20, 8, 2, can_sels, ARRAY_SIZE(can_sels)); hws[IMX6SX_CLK_UART_SEL] = imx_clk_hw_mux("uart_sel", base + 0x24, 6, 1, uart_sels, ARRAY_SIZE(uart_sels)); - hws[IMX6SX_CLK_QSPI2_SEL] = imx_clk_hw_mux_flags("qspi2_sel", base + 0x2c, 15, 3, qspi2_sels, ARRAY_SIZE(qspi2_sels), CLK_SET_RATE_PARENT); + hws[IMX6SX_CLK_QSPI2_SEL] = imx_clk_hw_mux("qspi2_sel", base + 0x2c, 15, 3, qspi2_sels, ARRAY_SIZE(qspi2_sels)); hws[IMX6SX_CLK_SPDIF_SEL] = imx_clk_hw_mux("spdif_sel", base + 0x30, 20, 2, audio_sels, ARRAY_SIZE(audio_sels)); hws[IMX6SX_CLK_AUDIO_SEL] = imx_clk_hw_mux("audio_sel", base + 0x30, 7, 2, audio_sels, ARRAY_SIZE(audio_sels)); hws[IMX6SX_CLK_ENET_PRE_SEL] = imx_clk_hw_mux("enet_pre_sel", base + 0x34, 15, 3, enet_pre_sels, ARRAY_SIZE(enet_pre_sels));
There is no dedicate parent clock for QSPI so SET_RATE_PARENT flag should not be used. For instance, the default parent clock for QSPI is pll2_bus, which is also the parent clock for quite a few modules, such as MMDC, once GPMI NAND set clock rate for EDO5 mode can cause system hang due to pll2_bus rate changed. Fixes: f1541e15e38e ("clk: imx6sx: Switch to clk_hw based API") Signed-off-by: Han Xu <han.xu@nxp.com> --- changes in v2 - fix the build break due to missing close parenthesis --- drivers/clk/imx/clk-imx6sx.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)