diff mbox series

[v2] ARM: dts: imx6qdl-gw54xx: add CAN regulator

Message ID 20220916153107.1802079-1-tharvey@gateworks.com (mailing list archive)
State Accepted
Headers show
Series [v2] ARM: dts: imx6qdl-gw54xx: add CAN regulator | expand

Commit Message

Tim Harvey Sept. 16, 2022, 3:31 p.m. UTC 
The GW54xx has a transceiver with a STBY pin connected to an IMX6 GPIO.
Configure this as a regulator to drive it low when CAN is in use.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
v2:
- move compatible to start of child node
- fix typo in commit log
---
 arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 18 +++++++++++++++++-
 1 file changed, 17 insertions(+), 1 deletion(-)

Comments

Shawn Guo Sept. 17, 2022, 4:23 a.m. UTC | #1 
On Fri, Sep 16, 2022 at 08:31:07AM -0700, Tim Harvey wrote:
> The GW54xx has a transceiver with a STBY pin connected to an IMX6 GPIO.
> Configure this as a regulator to drive it low when CAN is in use.
> 
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Applied, thanks!
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
index cda48bf2f168..a9b04f9f1c2b 100644
--- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
@@ -137,6 +137,16 @@  reg_3p3v: regulator@1 {
 			regulator-always-on;
 		};
 
+		reg_can1_stby: regulator-can1-stby {
+			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_reg_can1>;
+			regulator-name = "can1_stby";
+			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
 		reg_usb_h1_vbus: regulator@2 {
 			compatible = "regulator-fixed";
 			reg = <2>;
@@ -200,6 +210,7 @@  IMX_AUDMUX_V2_PTCR_SYN
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
 	status = "okay";
 };
 
@@ -687,7 +698,6 @@  pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b1
 			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b1
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
 		>;
 	};
 
@@ -786,6 +796,12 @@  MX6QDL_PAD_SD4_DAT2__PWM4_OUT		0x1b0b1
 		>;
 	};
 
+	pinctrl_reg_can1: regcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1